CONTENTS BEFORE USING THE APPLIANCE PRECAUTIONS AND GENERAL RECOMMENDATIONS DESCRIPTION OF THE APPLIANCE FILLING THE DETERGENT AND ADDITIVES REMOVING THE FILTER DRAINING RESIDUAL WATER CARE AND MAINTENANCE TRANSPORT / HANDLING INSTALLATION ELECTRICAL CONNECTION 35
BEFORE USING THE APPLIANCE 1.Removing the packaging and inspection 5.Drain • After unpacking, make sure that the appliance is undamaged. If in doubt, do not use the appliance. Contact After-Sales Service or your local retailer. • Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach of children, as they are potentially dangerous. • Connect the drain hose to the siphon or hook it over the edge of a sink with the “U” bend (see “Installation/Connect the water drain hose”).
PRECAUTIONS AND GENERAL RECOMMENDATIONS 1.Packing • The packing material is recyclable as indicated by the recycling symbol . Adhere to local regulations when disposing of packaging material. 2.Energy saving tips • Achieve the best use of energy, water, detergent and time by using the recommended maximum load size. • Do not exceed manufacturers’ recommended dosages as shown on the detergent package.
DESCRIPTION OF THE APPLIANCE 1. Worktop 2. Control panel 3. Detergent dispenser 4. Door 5. Door handle • To open the door press the button inside the handle and pull. • Close the door by pushing it firmly (the lock will click into place) 6. Filter (behind cover) 7. After-Sales Service sticker (inside door) 8. Adjustable feet 9.
REMOVING THE FILTER 1. 2. 3. 4. Stop the appliance and unplug it. Open the filter cover. Place a bowl beneath the filter. Slowly turn the filter anticlockwise without extracting it as yet. 5. Wait until all the water has drained. 6. Now unscrew the filter completely and extract it. 7. Remove any foreign items from the foreign body trap. 8. Insert the filter and screw it in clockwise until it locks, making sure it is hermetically closed. 9. Close the cover. 10. Pour 0.
CARE AND MAINTENANCE Appliance exterior and control panel Door seal • Clean using normal household cleaner (do not use abrasive products and no solvents). • Dry with a soft cloth. Filter • Clean with a damp cloth when necessary. • Check the condition of the door seal periodically. • Check and clean the filter two or three times a year (see “Removing the Filter”). Detergent dispenser (depending on model) 1.
INSTALLATION Remove the transport bolts For washing machines: 1. Slacken the three or four bolts (A) (according to model) with the spanner supplied. 2. Unscrew the bolts by hand. A A B B A For washer dryers: 3. Insert a screwdriver into the empty holes and tilt to remove the plastic spacers (C) (transport bolts) and retrieve them. Keep the transport bolts for future use. A B B A A A For washer dryers: 1.
Adjust the feet If the floor is uneven, adjust the levelling feet as required (do not insert pieces of wood, cardboard etc. under the feet): 1. Loosen the locknut using the wrench provided. 2. Adjust the height of the foot, turning it by hand. 3. Tighten the locknut anticlockwise towards the appliance. If the appliance is to be installed on a wooden floor, distribute the weight by placing it on a 60 x 60 (or 40) cm sheet of plywood at least 3 cm in thickness. Secure the plywood sheet to the floor.
ELECTRICAL CONNECTION For Great Britain only Warning - this appliance must be earthed Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows: 1. Remove the fuse cover (A) and fuse (B). 2. Fit replacement 13A fuse into fuse cover. 3. Refit both into plug.
Ecological Paper Printed in Italy 5019 301 20024 S N DK FIN GB 1/0505
