Installation Instruction

28
ELECTRONIC CONTROL SETUP INSTRUCTIONS
Control Setup Procedures
IMPORTANT: Read all instructions before operating.
The fabric setting buttons along with the digital display are used to
set up the dryer controls. The display can contain four numbers
and/or letters and a decimal point. These are used to indicate
the setup codes and related code values available for use in
programming the appliance.
How to Use the Buttons to Program the Controls
1. The WHITES AND COLORS button is used to adjust the values
associated with setup code. Pressing the button will change the
value by increments of one (1). Rapid adjustment is possible by
holding down the button.
2. The PERM. PRESS button will advance through the setup
codes. Pressing the button will advance to the next available
setup code. Holding down the PERM. PRESS button will
automatically advance through the setup codes at a rate faster
than one (1) per second.
3. The DELICATES button is used to select or deselect options.
IMPORTANT: The console must not be opened unless power is first
removed from the dryer. To access connector AA1:
→ Unplug dryer or disconnect power.
→ Open console, disconnect plug on AA1, close console.
→ Plug in dryer or reconnect power.
■
Stacked Coin Models: Insert access panel key and turn
counterclockwise.
■
Stacked Non-Coin / Card-Ready Models: Once the debit card
reader is installed (according to the reader manufacturer’s
instructions), the setup mode can be entered by inserting a
manual setup card (supplied by the reader manufacturer) into the
card slot.
If manual setup card is not available, manual setup mode can be
entered by turning the access panel key.
The dryer is now in the setup mode.
NOTE: This dryer is preset at the factory and does not require any
programming. However, if you want to change the settings, follow the
“Setup Codes” guide below.
■
Coin Units are preset at the factory for fixed cycle price with top
off.
■
Non-Coin / Card-Ready units are preset for free cycle operation
so they can be run without readers or coins.
Setup Codes
■
The PERM. PRESS button will advance you from code to code.
■
The WHITES AND COLORS button will change the code value.
■
The DELICATES button will select or deselect options.
FOR NON-COIN / CARD-READY MODELS: The setup codes are
the same as for the Coin models except where noted.
NOTE: On all stacked dryer models, programming selections apply
to both dryers. Stacked dryer selections are accessed by pressing
the LOWER DRYER buttons.
The setup code is indicated by the one or two left-hand characters.
The setup code value is indicated by the two or three right-hand
characters.
Code Explanation
606
REGULAR CYCLE PRICE
606 Represents the number of quarters (coin 1) needed to
start the dryer; may adjust from 0–39 (See VALUE OF
COIN 1 b.05). Advance from 0–39 by pressing the
WHITES AND COLORS button. Factory default of 6
quarters = $1.50.
NON-COIN / CARD-READY MODELS ONLY: Factory
preset for 0 quarters.
■
Press the PERM. PRESS button once to advance to
next code.
705
REGULAR DRY TIME
705 Represents the number of minutes per quarter (coin 1).
Factory default of 5 minutes per coin.
Example: 6 quarters x 5 minutes = 30 minutes.
By pressing the WHITES AND COLORS button, value
adjusts from 1 to the maximum minutes.
■
Press the PERM. PRESS button once to advance to
next code.
800
TYPE OF DRYER PRICING
800 Fixed Cycle with Top Off. For detailed description, see
“General User Information.”
8FC Fixed Cycle. For detailed description, see “General User
Information.”
Use DELICATES button to make this selection.
NON-COIN / CARD-READY MODELS ONLY: Factory
preset for FC.
■
Press the PERM. PRESS button once to advance to
next code.
9 00 CYCLE COUNTER OPTION
This option is either NOT SELECTED “OFF” or
SELECTED “ON.”
9 00 Not Selected “OFF.”
9 0C Selected “ON” and not able to be deselected.
■
Press the DELICATES button three consecutive
times to select “ON.” Once selected “ON” it cannot
be deselected.
■
Press the PERM. PRESS button once to advance to
next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Cycles in HUNDREDS 1 02 = 200
2 00 Cycles in ONES 2 25 = 25
TOTAL CYCLES = 225
This is “VIEW ONLY” and cannot be cleared.
■
Press the PERM. PRESS button once to advance to next code.