Instruction for Use

EN
21
Use & Care Guide
FUNCTION DESCRIPTIONS
TIMER FUNCTION
Press the Timer button
to switch the timer on
or o. The timer can be
set with 1h (one hour)
increments to between 0 and 24 hours whenever the Timer
button is pressed. After pressing and holding the Timer
button, the time will increase.
Setting the Timer ON function
The Timer ON function can be set when the appliance is in the
OFF status. Press the Timer button: the button background will
light up and "00h" will appear on the display panel (1); within 5
seconds, you can press the Timer button to select the desired
time when the appliance must switch on. Once the timer has
been set, the time will be displayed for 5 sec, the Timer ON/
OFF indicator will be on and the display panel will switch o.
The appliance will switch on automatically at the chosen time.
NOTE: If the time is not set within 5 seconds after pressing the
Timer button, the appliance will exit the Timer function.
Cancelling the Timer ON function
Press the Timer button again to enter the function: after the
button background lights up, press the Timer button until
the appliance displays "00h" and the Timer ON/OFF indicator
disappears. The function will have been cancelled.
Setting the Timer OFF function
The Timer OFF function can be set when the appliance is in
the ON status. Press the Timer button: the button background
lights up and "00h" appears on the display panel (1); within 5
seconds, press the Timer button to select the desired time for
the appliance to switch o. After the timer is set, the time will be
displayed for 5 sec and the Timer ON/OFF indicator turns on.
The appliance will switch o automatically at the chosen time.
RESETTING THE FILTER
When the Clean Filter
indicator lights up, the
lter needs cleaning.
After cleaning the air
lter, press the Fan and Humidity buttons simultaneously and
the lter indicator will turn o.
The air lter should be cleaned whenever the appliance signals
this need, so that the unit’s performance does not deteriorate.
CHILD LOCK FUNCTION
Press the Mode
and Timer buttons
simultaneously to
activate the child lock
function. "LC" will appear on the display panel to signal that
the buttons are locked, and the Mode and Timer buttons
will ash for a few seconds. No functions can be activated by
pressing the buttons.
Press the Mode and Timer buttons simultaneously once again
to unlock this function, the Mode and Timer buttons will ash
for a few seconds.
This function can be used when the appliance is switched
both o and on.
AUTO STOP FUNCTION
When the bucket is full, removed or not correctly inserted in
the unit, or when the humidity level is 5% lower than the set
humidity, the unit will stop operating automatically.
MEMORY FUNCTION
In case of a power failure, all settings will be memorised. Once
the power supply is restored, the unit will resume operating
according to the memorised settings.
WATER BUCKET FULL FUNCTION
If the water bucket is full or has been removed for over 3
minutes, the Water Full indicator will light up and emit a
"beep". The machine will resume operating once the water has
been drained and the bucket has been re-inserted.
AUTO POWER OFF
In Cont mode, the machine stops automatically when the
water bucket is full, the same occurs when the water bucket is
extracted or is incorrectly positioned.
AUTO DEFROST
During operation, the compressor will stop automatically
when frost covers the evaporator. The fan will run continuously
until the defrosting process terminates. The machine will then
restart automatically.
Timer
Timer ON/OFF
Dry
Fan Humidity
+
Timer ON/OFF
Filter Clean
Mode Timer
+
WATER DRAINAGE
DRAINING WATER THROUGH THE WATER BUCKET
The Water Full indicator lights up when the water bucket is full. The machine stops automatically and the water bucket will
have to be emptied.
1. Remove the water bucket
Pull the water bucket out by gripping both of its sides.
► Do not remove the sensor (19) on the water bucket used to measure the water level, as
water may leak out, thus damaging the unit and causing possible electric shock.
► The dirty water bucket can be washed using cold or warm water. Do not use solvents,
abrasiveproducts, petrol, chemicals, cloths or other materials to clean the bucket, as
these may damage it and cause water leakages.