GB User and maintenance manual
IMPORTANT SAFETY INSTRUCTIONS These instructions shall also be available on website: docs.whirlpool.eu. YOUR SAFETY AND THAT OF OTHERS IS HIGHLY IMPORTANT. This manual and the appliance itself provide important safety warnings, to be read and observed at all times. This is the attention symbol, pertaining to safety, which alerts users to potential risks to themselves and others.
• The ventilation ducts must always discharge to the outside. • Exhaust air must not be vented through a flue used for removal of fumes produced by appliances burning gas or other fuels, but must have a separate outlet. All national regulations governing extraction of fumes must be observed. • If the hood is used together with other appliances operating on gas or other fuels, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar). For this reason, make sure the room is adequately ventilated.
INSTALLATION After unpacking the appliance, check for any transport damage. In the event of problems, contact the dealer or your nearest After-sales Service. To prevent any damage, only remove the appliance from its polystyrene foam packaging at the time of installation. PREPARING FOR INSTALLATION WARNING: this is a heavy product; the hood should only be lifted and installed by two or more people.
GENERAL RECOMMENDATIONS Before use Remove cardboard protection pieces, protective film and adhesive labels from accessories. Check the appliance for any transport damage. Use only the fixing screws supplied with the product for installation or, if not supplied, purchase the correct screws type. Use the correct length for the screws which are identified in the Installation Guide. In case of doubt, consult an authorised service assistance centre or similar qualified person.
AFTER-SALES SERVICE Before calling the After-Sales Service: 1. See if you can solve the problem yourself with the help of the suggestions given in the "Troubleshooting guide". 2. Switch the appliance off and back on again it to see if the fault persists. If after the above checks the fault still occurs, get in touch with the nearest After-Sales Service.
Reset filter saturation After carrying out filter maintenance, press and hold button T1, LED L4 switches off. Activation of the LED for charcoal filter saturation The LED for charcoal filter saturation is normally disabled. To activate it, proceed as follows: With the hood off, press and hold for a long time and simultaneously T1 and T4: L1 flashes first then L2 as well, to indicate successful activation.
Replacing lamps The hood is equipped with a lighting system based on LED technology. The LEDs guarantee an optimum lighting, a duration up to 10 times as long as the traditional lamps and allow to save 90% electrical energy. For replacement, contact the technical service. TECHNICAL DATA Model Height (cm) Width (cm) Depth (cm) Ø of exhaust tube (cm) DGIFG 94 AM X 60.9 - 113 72.2 - 113 89.8 59.
1x 44x Ø 3,5x9,5 2x 6x x2 6x Ø 10x70 1x 8x 3x9 1x Ø 6x70 2x 1x x2 1x 1x 6x Ø 3,5x9,5 Ø 120 mm Ø 125 mm Ø 150 mm 1x 2x 2x 1x
R1 SX R1 FRONT SX 1 RX 220-240 V ~50-60Hz SX FRONT 3 2 6 5 4 RX 6 x Ø 10mm FRONT RX R2 4x Ø 10x70 mm RX SX FRONT 4x Ø 6x70mm 2 1 FRONT SX 1cm RX x2 FRONT x1 SX Ø 16cm RX 4 3 min 74 cm 76 cm L min max 103cm ³ 65 cm ³ 50 cm 5 H(cm) = L - 22,4 H
16 x Ø 3,5x9,5mm SX FRONT RX H - 7cm 6 7 ! 8 10 9
11a 11b
16 x Ø 3,5x9,5mm 12 13 x4 x1 14 15 x2
6x Ø 3,5x9,5mm = 17 8x Ø 3,5x9,5mm 18 =
X cm X cm x2 19
4 x Ø 3x9 20
X cm x2 21 22 X cm
23 25 400011235002 2x Ø 3x9mm 26 27 Printed in Italy 03/2018 GB Privileg Registered trademark/TM Trademark of Whirlpool group of companies - © Copyright Whirlpool Europe s.r.l. 2015. All rights reserved - www.whirlpool.