AUTOMATIC ICE MAKER Model ECUOOXP s. Freezers, Refngerator-Freezers. Ice Makers, Dishwashers. Built-In Ovens and Surface Units. Ranges. Microwave Ovens. Trash Compactors. Room Atr Condittoners.
Please read this Use and Care Guide . before you do anything else... This booklet tells you how to use and clean your ice maker. Treat your ice maker with care, use it only to do what ice makers are designed to do. Parts and features -/ CONTROL CYCLE CON-I lROL MODEL AND SERIAL NUMBER PLATE / (not shown) GRILLE Copy your Model and Serial Numbers here... When you need servjce, or call with a question, have this information ready: 1. Complete Model and Serial Numbers (from the plate located as shown].
Contents Page 3 . 4 ............ BEFOREYOUPLUGITIN.. USING YOUR ICE MAKER ............ How the Ice Maker Works ......... Setting the Controls ............... Changing the Bin Door Panel . , CLEANING AND CARING FOR YOUR ICE MAKER ......................... Cleaning Exterior Surfaces. ....... Cleaning the Condenser ......... 1 5 Cleaning the Ice Maker System. Cleaning the Interior Components. Filtering and Treating Water ...... VACATION AND MOVING CARE. . . . . . IF YOU NEED SERVICE OR ASSISTANCE 1.
Using your ice maker How the ice maker works... 3. The water containing the rejected is drained after each freezing cycle. 4. Fresh water enters the machine ice making cycle. minerals for the next 1. Water is constantly circulated over a freezing plate. As the water freezes into ice the minerals in the water are rejected. This produces a clear sheet of ice with a low mineral content bin is full the ice maker shuts off automatically and restarts when more ice is needed. 2.
2. To start the normal ice making the Cycle Control Knob to “ON:’ 3. To stop ice maker operation, Control Knob to “OFF.” cycle, turn turn Cycle The “CLEAN” setting is used whenever solutions are circulated through the ice maker for cleaning. Only the water pump operates at this setting. Changing the bin door panel You can easily change the color of the front panel on the storage bin door. Six colors are available: Black, Almond, Harvest Gold, White, Toast and Platinum. To change panel: _ - 1.
Cleaning and caring for your ice maker Periodically inspect and clean the ice maker to keep it operating at peak efficiency and to prevent premature failure of system components. Both the ice making system and the air cooled condenser need to be cleaned regularly. The minerals rejected from the circulating water during the freezing cycle will eventually form a hard scaly deposit in the water system which prevents a rapid release of the ice from the freezing plate.
1. Place the Cycle position. Control Knob in the “OFF” 2. Remove the two thumb screws and slide the ice cutter grid forward, out of the two slots near the water pan. 3. Unplug the electrical CAUTION: be melted harness. Any ice on the grid should under running warm water. grid may stretch and damage 4. Remove all ice from the storage freezing plate. grid wires. bin and the 6. Pour YZgallon (1.
Cleaning the interior components 1. Turn the Cycle Control Knob to “OFF” and disconnect the electrical power supply to the machine. Open the storage bin door and remove any ice that is in the bin, 2. Remove ice retainer baffle by flexing then slide it off the studs. it and 3. Remove the ice cutter grid by unscrewing the two thumb screws, slidino the arid forward and unplugging the electrical wire harness WATER PAN - INTO nDAl 4. Remove the water pan by unscrewing two thumb screws.
Filtering and treating water In most areas it will be beneficial to filter or treat the water being supplied to the ice machine. It can improve the reliability of the machine, reduce water system maintenance and produce the best quality of ice. The installation of a polyphosphate feeder will generally reduce scale build-up and the ice machine will require less frequent cleaning. Municipal water systems are generally treated with chlorine to maintain a safe potable water supply.
If you need service or assistance, we suggest you follow these four steps: 1. Before calling for assistance... Performance problems often result from little things you can find and fix yourself without tools of any kind. Grid is not cutting ice sheets: Check the grid harness plug to make sure the connection is secure. l Unit does not run: Cycle Control Knob must be in the “ON” position. l Check to see that power cord is plugged in.
2. If you need assistance?.. 4. If you have a problem?.. Call Whlrlpool COOL-LINE@ service asslstance telephone number. Dial free from: Contlnental U.S.. . . . . . . . (800) 253-1301 Michigan . . . . . . . . . . . . . . (800) 632-2243 Alaska & Hawaii . . . . . . . (800) 253-1121 Call our COOL-LINE service assistance telephone number (see Step 2) and talk with one of our Consultants, or if you prefer, write to: Mr. Stephen E.
Home L Appliances Maklng your world a little easier. Part No. 758558 01985 Whirlpool Corporation Printed in U.S.A. Makers, Dishwashers. Built-In Ovens and Surface Units. flanges. Microwave Ovens.