Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 Rebel UI Module (FCC ID: A5UEICHRB01) USER GUIDE Rev 1.
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 Contents Contents .......................................................................................................................... 2 1 2 3 4 Introduction .............................................................................................................. 4 1.1 Purpose and scope ...................................................................................................... 4 1.2 Revision History ...................
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 Figures Figure 1: System Block Diagram ................................................................................ 6 Figure 2: Accessories Details_1 ................................................................................. 7 Figure 3: Accessories Details_2 ................................................................................. 8 Figure 4: PCB Top Side ..........................................................................
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 1 1.1 Introduction Purpose and scope The purpose of this document is to provide details regarding the use of rebel UI Module. This document also describes the application and operation of it. Moreover, it declares the FCC compliance notices, too. 1.2 Revision History Date 16-04-2019 18-04-2019 29-04-2019 Rev 1.0 Change Description Initial release Review comments are implemented Release to TuV Page 4 Revision 0.1 0.2 1.
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 2 Module Overview 2.1 Module Application REBEL UI Module is the platform which will be used across different appliances categories (Refrigeration, Cooking, Laundry, Dishwashers, etc.) based on Qualcomm Snapdragon 660 (SDA 660) processor. The Rebel UI Module is 2.4G/5G Wi-Fi-connected graphical user interface. It supports LCD with touch-screen and audio video interfaces. Rev 1.
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 2.2 System Level Architecture Figure 1: System Block Diagram REBEL UI module consist of the PCBA and Heat Sink, all other external peripherals connected are accessories only. Below is the list of accessories (shown in the images) LCD USB Camera Speaker Plastic cover ( to hold the PCB and LCD) Touch Panel with glass 8MP Camera Sensor PCB Rev 1.
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 Figure 2: Accessories Details_1 Rev 1.
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 Figure 3: Accessories Details_2 2.3 Major Part Details for the PCB Figure 2 shows the major connectors of the peripheral supported by the module that resides on the top side of the PCB. Rev 1.
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 Figure 4: PCB Top Side Figure 3 shows the major connectors of the peripheral supported by the module that resides on the bottom side of the PCB. Figure 5: PCB Bottom Side Rev 1.
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 2.4 Compliance Limits The register value used for FCC compliance is maximum value and cannot be increased by end user. The RF Output Power configuration is not accessible to End User. 2.5 Module Features and Operation The rebel UI module intended to operate with pre-certified power supply of typical voltage 12.7VDC ranging from 11V-13.5V. The Module has the high bandwidth Wi-Fi module (WCN3990) for data and video transfer over Wi-Fi interface.
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 Antenna Type ANT Chain ANT MFG Antenna Part# Maximum Gain (dBi) FPCFlexible printed circuit 0 Molex 1461530050 3.2dBi(2.4 2.5 GHz) Required Impedance – 50 ohms 4.75dBi (5.15 – 5.85 GHz) FPCFlexible printed circuit 1 Molex 1461530150 2.8dBi(2.4 2.5 GHz) – 50 ohms 4.2dBi (5.15 – 5.
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 The antenna(s) used for this transmitter must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and all persons at all times and must not be co-located or operating in conjunction with any other antenna or transmitter.
Whirlpool Corporation 2000 M-63 Benton Harbor, MI 49022 IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the FCC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. 3.