Manual

ManualsBrandsWhirlpool ManualsPlumbing Product50-Gallon 12-Year Regular Electric Water Heater

WATER

HEATERS

Installation

Instructions and

Use & Care Guide

To obstain technical, warranty, or service assistance during or after the

installation of this water heater, visit our website at:

http://www.whirlpoolwaterheatersupport.com

or call tool free

1-877-817-6750

When calling for assistance, please have the following information ready:

1. Model Number 4. Date of Installation

2.7 Digit Product Number 5. Place of Purchase

3. Serial Number

Table Of Contents PAGE

Water Heater Safety ............................................................................ 2

Installing Your Electric Water Heater ................................................... 3-9

Unpacking Instructions ................................................................... 3

Location Requirements .................................................................. 4

Water System Piping ................................................................... 5

Electrical Requirements ................................................................. 7

Installation Checklist ...................................................................... 9

Operating Your Water Heater ............................................................. 10-12

Water Heater Start-Up ................................................................... 10

Water Temperature Regulation ...................................................... 10

Energy Smart _ Module/Operational Modes ................................... 11

Electronic Thermostat .................................................................... 12

Smart Grid Technology .................................................................. 13

Operational Conditions ................................................................... 14

Maintenance of Your Water Heater .................................................... 15-23

Diagnostic Code (ESM) .................................................................. 17-18

Diagnostic Code (ET) .................................................................... 19-20

Trouble Shooting Chart ..................................................................... 21

Repair Parts illustration ................................................................... 22

Thermostat Wiring Diagram ............................................................ 23

LOW LEAD

COMPLIANT

PRINTED IN THE U.S.A 0411 PART NO. 318686-000

Summary of content (24 pages)

PAGE 1
® ol WATER HEATERS Installation Instructions and Use & Care Guide To obstain technical, warranty, or service assistance during or after the installation of this water heater, visit our website at: http://www.whirlpoolwaterheatersupport.com or call tool free 1-877-817-6750 When calling for assistance, 1. Model 2.7 Digit Product 3. Serial Number ................................................................... .................................................................. Water System .....
PAGE 2
WATER HEATER SAFETY Your safety and the safety or others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This symbol alerts you to potential hazards that can kill or hurt you and others. All willsymbol. follow the safety alert symbol and either the word "DANGER" or Thissafety is themessages safety alert "WARNING".
PAGE 3
INSTALLING YOUR WATER HEATER Consumer Information This water heater should be installed in accordance with the local code authority having jurisdiction, the power company or electric utility, and this installation manual. In the absence of local code requirements, follow the regulations set forth in the latest edition of the National Electric Code, NFPA70. This is available from the following: Insulation Blankets The use of an insulation blanket on this water heater is not needed nor recommended.
PAGE 4
Location Requirements Site location Select a location near the center of the water piping system. It must be installed indoors and in a vertical position on a level surface, in an area where water leakage will not cause consequential damage. NOTE: Local codes and requirements in your area may require the water heater to be installed such that the bottom element is elevated from the floor at least 18 inches. The water heater should be located in an area not subject to freezing temperatures.
PAGE 5
Water System Piping Piping Installation Piping, fittings, and valves should be installedaccording to the installation drawing (Figure 3). If the indoor installation area is subject to freezing temperatures, the water piping must be protected by insulation. Water supply pressure should be around 50 to 60 psi and should not exceed 80 psi. If this occurs, a pressure reducing valve should be installed in the cold water inlet line.
PAGE 6
Please note the following: DO NOT install this water heater with iron piping. The system should be installed only with piping that is suitable for potable (drinkable) water such as copper, CPVC, or polyethylene (PEX). DO NOT use PVC water piping. Temperature and Pressure Relief Valve Explosion DO NOT use any pumps, valves, or fittings that are not compatible with potable water. Hazard • Temperature-pressure relief valve must comply with ANSI Z21.22-CSA 4.4 and ASME code.
PAGE 7
The Temperature & Pressure Relief Valve: • Must be connected to an adequate discharge line. • Must not be in contact with any electrical part. • Must not be rated higher than the working pressure shown on the data plate of the water heater. The Discharge Line: • Must not be smaller than the pipe size of the relief valve or have any reducing coupling installed in the discharge line.
PAGE 8
• Wiringisenclosed inapproved conduit(ifrequired bylocalcodes). • Thewaterheaterandelectrical supplyareproperly grounded. Alwaysreference thewiringdiagram forthecorrectelectricalconnection. Thecomplete wiringdiagram canalsobe foundonthetopofthewaterheaternearthejunctionbox cover.
PAGE 9
, , Connect the black power wire from the home's electrical service to the heater's TWO black wires and secure with the appropriate size wire nut. When you are done, you will have THREE black wires under one wire nut. Locate and connect the remaining power wire (usually red, but in your home this wire may be some other color) from the home's electrical service to the water heater's TWO red wires and secure with the appro priate size wire nut.
PAGE 10
OPERATING YOUR WATER HEATER Water Temperature Regulation Water Heater Start-Up 1. Carefully read and understand the section, "Water Temperature Regulation" section of this manual. If the instructions are not clear, contact a qualified person. 2. Make sure the water heater has been properly installed. See "Installing Your Water Heater" section. 3. Completely fill the tank water, Open faucet to allow air to purge (see page 5, step 7). 4.
PAGE 11
Adjusting the Energy Smart ®Module/Operational Modes Water Temperature Adjustment IMPORTANT: Before attempting to adjust the thermostat, read the "Water Temperature Regulation" section on page 10. If the instructions are not clear, contact a qualified person. The water temperature can be adjusted from 80 ° F to 150 ° F. Use the Up and Down Buttons | desired temperature.
PAGE 12
The Electronic Thermostat IMPORTANT: The Energy Smart s Module (ESM) must be removed before attempting to access the thermostat. NOTE: for the Electronic Thermostat (ET) changes to remain in effect the Energy Smart s Module (ESM) must no._[t be reconnected, also read the "Water Temperature Regulation" under the "Operating Your Water Heater" section. If the instructions are not clear, contact a qualified person. Electrical Shock Hazard Do not remove the plactic guard from over wiring.
PAGE 13
Smart Grid Technology The electric Smart Grid will enable significant improvements in electric power reliability and quality through reduction of peak power demand, while providing consumers the knowledge and ability to manage their energy consumption and utility costs. According to the Department of Energy (DOE), since 1982 the growth in peak electricity demand has exceeded power transmission growth.
PAGE 14
Operational Conditions Anode Rod/Water Water Heater Sounds Odor Each water heater contains at least one anode rod, which will slowly deplete (due to electrolysis) prolonging the life of the water heater by protecting the glass-lined tank from corrosion. Adverse water quality, hotter water temperatures, high hot water usage, hydronic heating devices, and water softening methods can increase the rate of anode rod depletion.
PAGE 15
MAINTENANCE OF YOUR WATER HEATER If you lack the necessary skills required to properly service this water heater or you have difficulty following the instructions, you should not proceed but have a qualified person perform the maintenance of this water heater. Draining and Flushing Temperature Relief Valve It is recommended that the tank be drained and flushed every 6 months to remove sediment which may buildup during operation.
PAGE 16
Heating Element Replacement Figure 14 Element and Thermistor Lower Thermistor Sensor (Must Have Good Contact With Tank, Sensor Electrical Disconnect servicing. Shock Hazard 2. Drain the water heater as directed under "Draining and Flushing" section. Remove the access cover(s), then remove the insulation and element cover(s). Remove the plastic guard covering electric wiring. 4. /1 --.
PAGE 17
Diagnostic Code Chart Energy Smart ® Module (ESM) ( IMPORTANT: Before attempting to adjust the thermostat, read the "Water Temperature Regulation" section page 10. ENERGY SMART The Electronic Thermostat (ET) is designed so that it may control the water heater without the Energy SmarP Module (ESM) being operated, see page 12. STANDARD VACATION GR_O E.AB[ED I EI Error Code ! -Alert Icon If the instructions are not clear, contact a qualified person. U.
PAGE 18
INDICATES (ESM) ERROR CODE E51 with an alert Icon flashing. A failure to communicate E71 with an alert Icon flashing. with an alert Icon flashing. CORRECTIVE ACTION* 1. Turn off electrical power at the breaker, check all electrical and wiring for damage. 2. Replace the Electronic Thermostat (ET). 3. Turn on electrical power at breaker. connections, Energy Smart® Module (ESM) is receiving the wrong data from the Electronic Thermostat (ET). 1.
PAGE 19
Diagnostic Code Chart Electronic Thermostat (ET) IMPORTANT: Before attempting to adjust the thermostat, read the "Water Temperature Regulation" section page 10. Setpoint Knob Diag LED Light The Electronic Thermostat (ET) is designed so that it may control the water heater without the Energy Smart_ Module (ESM) being operated, see page 12. Electrical Shock Hazard Do not remove the plactic guard from over wiring. Do not touch electrical wiring.
PAGE 20
(ESM) ERROR CODE (ET) DIAGNOSTIC INDICATES E9 9, 10, 11 or 12 FLASHES El0 (Red) Ell E12 CORRECTIVE ACTION* LED Electronic Thermostat (ET) error 1. 2. 3. 4. Turn off electrical power. Check wiring at Electronic Thermostat (ET) for damage. Turn on electrical power at breaker. If this code flashes condition continues, replace the Electronic Thermostat (ET). *These instructions are brief and intended as guidance for a qualified person.
PAGE 21
Troubleshooting Chart PROBLEM POSSIBLE CAUSE(S) CORRECTIVE ACTION* NO HOT WATER 1. No power to heater. 2. High temperature limit shut-down. 3. Defective sensor. 1. Refer to "E02" of Diagnostic Code Chart- page 17. 2. Refer to "E03 or E07" of Diagnostic Code Chart- page 17. 3. Refer to "No Light" of Diagnostic Code Chart- page 19. INSUFFICIENT 1. 2. 3. 4. 5. 6. 7. Defective lower element. Temperature set too low. Sediment or lime in tank. Defective Dip Tube. Heater too small for job.
PAGE 22
REPAIR PARTS ILLUSTRATION @ ® Repair Parts ITEM PARTS DESCRIPTION No. Repair parts may be ordered through your plumber, local distributor, home improvement center, or by calling 1-877-817-6750. When ordering repair parts, always give the following information: 1. Model, serial and product number 2. Item number 3. Parts description Repair Parts List Legend 4)' Special anode rod (See page 14) • Temperature and Pressure Relief Valve is required, but may not be factory installed.
PAGE 23
THERMOSTAT WIRING DIAGRAM FUSEDDISCONNECT OR CIRCUITBREAKER :.i-'.i BRANCH CIRCUIT g Nj Based on N.E.C. ELECTRONIC THERMOSTAT(ET) ® WATT LOAD ® @ a-- BLUE o_ UPPER_ ELEMENT"_,.#t..1 p,n TEMPERATURE SENSOR Recommend Over Current Protection Rating 120 V 15 20 30 30 B--1500" 2000 2500 3000 3500 4000 4500 5000 5500 SIZING GUIDE NFPA NO. 70 - 1999 208 V 15 15 15 20 20 25 30 30 240 V 15 15 15 15 20 20 25 30 30 Wattages less than 1500 may be wired 15 amp protection. BLUE _ i \ BLACK I I
PAGE 24
® Registered trademark/TM trademark of Whirlpool, U.S.A. © 2011 Whirlpool Corporation. All rights reserved. Energy Smart® is a trademark of American Water Heater Company Manufactured under license by American Water Heater Company, Tennessee. Warranty provided by manufacturer.