Instruction for Use

20
GB
 The first time you switch your appliance on, heat
the empty oven to its maximum temperature for at
least half an hour, making sure the door is kept shut.
Ensure that the room is well ventilated before
switching the oven off and opening the oven door.
The appliance may emit a slightly unpleasant odour
caused by protective substances used during the
manufacturing process burning away.
 Every time the oven is switched on it is set to the
Création menu.
 If the user does not touch any of the buttons after
the oven is switched on, it will switch off again
automatically after 2 minutes.
Switching the oven on for the first time
After connecting the oven to the electricity supply, the
first time it is switched on the user should also switch on
the control panel by pressing the
button. The list of
languages in the SETUP menu will appear. To choose
the desired language select it using the
and
buttons. The character in bold indicates which language
has been chosen. Press the OK button to confirm.
Once the selection has been made, the display will
show the following parameters:
LANGUAGE Choose language
TIME Set the time
SOUND Keypad sounds
CLOCK Display the clock
SAFETY INFO Display the info text
EXIT Exit the setup menu
 After choosing the language in the SETUP menu, if
the display is not used for another 60 seconds it will
automatically revert to the Création menu.
Setting the clock
To set the clock, switch on the oven by pressing the
button, then press the SETUP button and follow
the steps described.
1. Select the TIME command and press OK to
begin modifying the value.
2. Adjust the hour figure using the
or buttons.
3. Press the OK button to confirm.
4. Repeat the process to set the minutes.
Setting the timer
The timer can be set while the oven is switched off
or while it is switched on, when navigating the menu
for a cooking mode. When the set time has elapsed,
the oven will emit a sound signal. This will
automatically stop after one minute or when any
symbol on the control panel is pressed.
To set the timer press the
button and adjust the
minutes using the
or buttons.
Press the OK button to confirm.
 The timer does not switch the oven on or off.
Child Lock
The Child Lock function may be used to lock the
oven door and controls.
To activate the function, press the
button followed
by the "OK" button to confirm the setting.
To deactivate the function, repeat the procedure
described above.
The child lock function can be activated when a
cooking programme is in progress or when the oven
is switched off, or when a cooking end time has
been set and the start button pressed. The child
lock function can also be deactivated in all the
above situations and after the oven has completed
the cooking programme.
Demo mode
The oven can operate in DEMO mode: all heating
elements are deactivated, and controls remain
operative.
To enable the DEMO mode, press the
, button and
the
button in sequence, followed by the "OK"
button, when the oven is switched on. To disable the
mode, press the
button and the button in
sequence when the oven is switched on.
A buzzer sounds and the display shows Demo
Off.
The Demo mode can only be activated when the
oven is switched on and no cooking programme has
been commenced.
Starting the oven
 Every time the oven is switched on it is set to the
Création menu.
1. Switch the control panel on by pressing the
button.
2. Press the button relating to the desired Création
cooking mode
or Succès cooking mode. The
display will show the list of available programmes.
4. Use the
or buttons to select the desired
programme and confirm by pressing OK. The
display will show the temperature and the set duration
(only the duration is shown for Succès modes).
3. Press the START/STOP button to begin cooking.
4. The oven will begin its preheating stage.
5. When the preheating process has finished, a
buzzer sounds and all current preheating indicator
lights show that this stage has been completed:
6. During cooking it is always possible to:
- Modify the temperature by pressing the
button,
adjust the figure using the
or buttons and confirm
Start-up and use