Instructions for use WASHING MACHINE Contents GB English,1 CZ Česky,13 SK Slovensky,25 GB Installation, 2-3 Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data Care and maintenance, 4 RO Română,37 Cutting off the water or electricity supply Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose Precautions and tips, 5 General safety Disposa
Installation GB ! Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance. venness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured in relation to the worktop, must not exceed 2°. Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise and prevent it from shifting while it is operating.
Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a drain duct or a wall drain situated between 65 and 100 cm from the floor; ! Do not use extension cords or multiple sockets. ! The cable should not be bent or compressed. ! The power supply cable must only be replaced by authorised technicians. Warning! The company shall not be held responsible in the event that these standards are not observed.
Care and maintenance GB Cutting off the water and electricity supplies Caring for the door and drum of your appliance • Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washing machine and help to prevent leaks. • Always leave the porthole door ajar in order to prevent unpleasant odours from forming. • Unplug the washing machine when cleaning it and during all maintenance work.
Precautions and tips ! This washing machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully. General safety • This appliance was designed for domestic use only.
Description of the washing machine GB Control panel CLEANING ACTION ON/OFF button button SPIN SPEED button DISPLAY Detergent dispenser drawer WASH CYCLE SELECTOR MY CYCLE button START/PAUSE button with indicator light FUNCTION buttons buttons ANTI ALLERGY RINSE button DELAY TIMER button TEMPERATURE button CHILD LOCK button Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”).
Display GB Z B A X D C E Y F The display is useful when programming the machine and provides a great deal of information. The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all information relating to the progress status of the wash cycle. String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been set, the time remaining until the start of the selected wash cycle.
Running a wash cycle GB 1. SWITCH THE MACHINE ON. Press the On/Off button ; the text POWER ON will appear on the display and the START/PAUSE indicator light will flash slowly in a green colour. 2. LOAD THE LAUNDRY. Open the porthole door. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of programmes on the following page. 3. MEASURE OUT THE DETERGENT.
Wash cycles and functions Fabric softener Max.
Detergents and laundry GB Detergent dispenser drawer Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause a build up on the inside of your appliance and contribute to environmental pollution. ! Use powder detergent for white cotton garments, for pre-washing, and for washing at temperatures over 60°C. ! Follow the instructions given on the detergent packaging.
Troubleshooting Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be solved easily using the following list. GB Problem: Possible causes / Solutions: The washing machine does not switch on. • The appliance is not plugged into the socket fully, or is not making contact. • There is no power in the house. The wash cycle does not start. • • • • • The washing machine door is not closed properly.
Service GB Before calling for Assistance: • Check whether you can solve the problem alone (see “Troubleshooting”); • Restart the programme to check whether the problem has been solved; • If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate. ! Always request the assistance of authorised technicians. Have the following information to hand: • the type of problem; • the appliance model (Mod.); • the serial number (S/N).
Návod k použití PRAČKA Obsah CZ Česky CZ Instalace, 14-15 Rozbalení a vyrovnání do vodorovné polohy Připojení k elektrické a k vodovodní síti První prací cyklus Technické údaje Údržba a péče, 16 Uzavření přívodu vody a vypnutí elektrického napájení Čištění pračky Čištění dávkovače pracích prostředků Péče o dvířka a buben Čištění čerpadla Kontrola přítokové hadice na vod Opatření a rady, 17 Základní bezpečnostní pokyny Likvidace Manuální otevření dvířeku FMSDN 623 Popis pračky, 18-19 Ovládací panel
Instalace CZ ! Je důležité uschovat tento návod tak, abyste jej mohli kdykoli konzultovat. V případě prodeje, darování nebo přestěhování pračky se ujistěte, že zůstane uložen v blízkosti pračky, aby mohl posloužit novému majiteli při seznámení s její činností a s příslušnými upozorněními. ! Pozorně si přečtěte uvedené pokyny: obsahují důležité informace týkající se instalace, použití a bezpečnosti při práci. Rozbalení a vyrovnání do vodorovné polohy Rozbalení 1. Rozbalte pračku. 2.
Připojení vypouštěcí hadice 65 - 100 cm Připojte vypouštěcí hadici, aniž byste ji ohýbali, k odpadovému potrubí nebo k odpadu ve stěně, který se nachází od 65 do 100 cm nad zemí; nebo ji uchyťte k okraji umývadla či vany a připevněte vodicí držák z příslušenství ke kohoutu (viz obrázek). Volný konec vypouštěcí hadice nesmí zůstat ponořený do vody.
Údržba a péče CZ Uzavření přívodu vody a vypnutí elektrického napájení • Po každém praní uzavřete přívod vody. Tímto způsobem dochází k omezení opotřebení pračky a ke snížení nebezpečí úniku vody. • Před zahájením čištění pračky a během operací údržby vytáhněte zástrčku napájecího kabelu z elektrické zásuvky. Čištění pračky • Vnější části a části z gumy se mohou čistit hadrem navlhčeným ve vlažné vodě a saponátu. Nepoužívejte rozpouštědla ani abrazivní látky.
Opatření a rady ! Pračka byla navržena a vyrobena v souladu s platnými mezinárodními bezpečnostním předpisy. Tato upozornění jsou uváděna z bezpečnostních důvodů a je třeba si je pozorně přečíst. skončení jeho životnosti do odděleného sběru. Spotřebitelé by měli kontaktovat příslušné místní úřady nebo svého prodejce ohledně informací týkajících se správné likvidace starého zařízení. Základní bezpečnostní pokyny Manuální otevření dvířek • Toto zařízení bylo navrženo výhradně pro použití v domácnosti.
Popis pračky CZ Ovládací panel Tlačítko ON/OFF Tlačítko Tlačítko TYP PRANÍ ODSTŘEĎOVÁNÍ Displej Tlačítka Dávkovač pracích prostředků VOLBY PROGRAMŮ Tlačítko s kontrolkou START/PAUSE Tlačítko PAMĚŤ FUNKČNÍ tlačítka Tlačítko TYP MÁCHÁNÍ Tlačítko ODLOŽENÉHO STARTU Dávkovač pracích prostředků: slouží k dávkování pracích prostředků a přídavných prostředků (viz „Prací prostředky a prádlo“). Tlačítko ON/OFF : zapněte nebo vypněte pračku krátkým stisknutím tlačítka.
Displej CZ Z B A X D C E Y F Displej slouží k naprogramování zařízení a poskytuje četné informace. Ve dvou horních řetězcích A a B je zobrazen zvolený prací program, probíhající fáze praní a všechny informace o postupu programu. V řetězci C je zobrazena doba zbývající do konce probíhajícího pracího cyklu a v případě nastavení ODLOŽENÉHO STARTU také doba chybějící do zahájení zvoleného programu.
Jak provést prací cyklus CZ 1. ZAPNUTÍ ZAŘÍZENÍ. Stiskněte tlačítko a na displeji se zobrazí nápis ZAPNUTO; kontrolka START/PAUSE bude pomalu blikat zelenou barvou. 2. NAPLŇTE PRAČKU PRÁDLEM. Otevřete dvířka. Naplňte pračku prádlem a dbejte přitom, aby nedošlo k překročení množství náplně, uvedeného v tabulce programů na následující straně. 3. DÁVKOVÁNÍ PRACÍHO PROSTŘEDKU.
Programy a funkce Spotřeba energie kWh Celkové množství vody lt Doba trvání cyklu Max. náplň (kg) Zbytková vlhkost % Aviváž Prací prostředky Praní Max. teplot (°C) Max. rychlost (otácky za minutu) Bělicí prostředek Popis programu CZ Předpírka Programy Tabulka pracích programů - - - 170’ 60’ CLEAN Plus 1 ODSTRAŇOVÁNÍ SKVRN (1° stisknutí tlacítka) 1 ODSTRAŇOVÁNÍ SKVRN RYCHLÝ (2° stisknutí tlacítka) BAVLNA STANDARD 60°C (1) (1° stisknutí tlacítka): mimořádně 2 znečištěné bílé prádlo.
Prací prostředky a prádlo CZ Dávkovač pracích prostředků Dobrý výsledek praní závisí také na správném dávkování pracího prostředku: použití jeho nadměrného množství snižuje efektivitu praní a napomáhá tvorbě vodního kamene na vnitřních částech pračky a zvyšuje znečištění životního prostředí. ! Pro předpírku a praní při teplotě vyšší než 60 °C používejte práškové prací prostředky pro bílé bavlněné prádlo. ! Dodržujte pokyny uvedené na obalu pracího prostředku.
Poruchy a způsob jejich odstranění Může se stát, že pračka nebude fungovat. Dříve, než zatelefonujete na Servisní službu (viz „Servisní služba“), zkontrolujte, zda se nejedná o problém, který lze snadno vyřešit s pomocí následujícího seznamu. Poruchy: Možné příčiny / Způsob jejich odstranění: Pračku nelze zapnout. • Zástrčka není zasunuta v zásuvce nebo není zasunuta natolik, aby došlo ke spojení kontaktů. • V celém domě je vypnutý proud. Nedochází k zahájení pracího cyklu.
Servisní služba CZ Před přivoláním Servisní služby: • Zkontrolujte, zda nejste schopni poruchu odstranit sami (viz „Poruchy a způsob jejich odstranění“); • Opětovně uveďte do chodu prací program, abyste ověřili, zda byla porucha odstraněna; • V opačném případě se obraťte na Centrum servisní služby na telefonním čísle uvedeném na záručním listu. ! Nikdy se neobracejte s žádostí o pomoc na techniky, kteří nejsou k výkonu této činnosti oprávněni.
Návod na použitie PRÁČKA Obsah SK Slovensky SK Inštalácia, 26-27 Rozbalenie a vyrovnanie do vodorovnej polohy Pripojenie k elektrickej a k vodovodnej sieti Prvý prací cyklus Technické údaje Údržba a starostlivosť, 28 Uzavretie prívodu vody a vypnutie elektrického napájania Čistenie práčky Čistenie dávkovača pracích prostriedkov Starostlivosť o dvierka a bubon Čistenie čerpadla Skontrolujte prítokovú hadicu vodu Opatrenia a rady, 29 Základné bezpečnostné pokyny Likvidácia Manuálne otvorenie dvierok F
Inštalácia SK ! Je veľmi dôležité uschovať tento návod kvôli prípadnému ďalšiemu použitiu. V prípade predaja, darovania alebo presťahovania práčky sa uistite, že zostane uložený v jej blízkosti, aby mohol poslúžiť novému majiteľovi pri oboznámení sa s činnosťou a s príslušnými upozorneniami. ! Pozorne si prečítajte uvedené pokyny: obsahujú dôležité informácie, týkajúce sa inštalácie, použitia a bezpečnosti pri práci.
Pripojenie vypúšťacej hadice 65 - 100 cm Pripojte vypúšťaciu hadicu, bez toho aby ste ju ohli, k odpadovému potrubiu alebo k odpadu v stene, ktorý sa nachádza od 65 do 100 cm nad zemou; alebo ju uchyťte k okraju umývadla či vane, a pripevnite vodiaci držiak z príslušenstva ku kohútu (viď obrázok). Voľný koniec vypúšťacej hadice nesmie zostať ponorený do vody.
Údržba a starostlivosť SK Uzavretie prívodu vody a vypnutie elektrického napájania • Po každom praní uzatvorte prívod vody. Týmto spôsobom sa znižuje opotrebenie rozvodu vody zariadenia a znížuje sa nebezpečenstvo úniku vody. • Pred zahájením čistenia práčky a počas údržby je potrebné vytiahnuť zástrčku prívodného kábla zo zásuvky. Čistenie práčky • Vonkajšie časti a časti z gumy môžu byť čistené utierkou navlhčenou vo vlažnej vode a saponáte. Nepoužívajte rozpúšťadlá alebo abrazívne prostriedky.
Opatrenia a rady ! Práčka bola navrhnutá a vyrobená v súlade s platnými medzinárodnými bezpečnostnými predpismi. Tieto upozornenia sú uvádzané z bezpečnostných dôvodov a je potrebné si ich pozorne prečítať. Základné bezpečnostné pokyny • Toto zariadenie bolo navrhnuté výhradne na použitie ako spotrebič.
Popis práčky SK Ovládací panel Tlačidlo Tlačidlo TYP PRANIA ON/OFF Tlačidlo ODSTREĎOVANIA DISPLAY Tlačidlá Dávkovač pracích prostriedkov VOĽBY PROGRAMOV Tlačidlo PAMAŤ Tlačidlo START/PAUSE FUNKČNÉ tlačidlá TYP PLÁKANIA Tlačidlo Tlačidlo s kontrolkou ONESKORENÉHO ŠTARTU Tlačidlo TEPLOTY Tlačidlo ZABLOKOVANIE TLAČIDIEL Dávkovač pracích prostriedkov: slúži na dávkovanie pracích prostriedkov a prídavných prostriedkov (viď „Pracie prostriedky a prádlo“).
Displej SK Z B A X D C E Y F Displej slúži na naprogramovanie zariadenia a poskytuje všetky potrebné informácie. V dvoch horných reťazcoch A a B je zobrazený zvolený prací program, prebiehajúca fáza prania a všetky informácie o postupe programu. V reťazci C je zobrazená doba zostávajúca do konca prebiehajúceho pracieho cyklu, a v prípade nastavenia ONESKORENÉHO ŠTARTU, aj dobu zostávajúcu do zahájenia zvoleného programu.
Ako vykonať prací cyklus SK 1. ZAPNUTIE ZARIADENIA. Stlačte tlačidlo a na displeji sa zobrazí nápis ZAPNUTÉ; kontrolka START/PAUSE bude pomaly blikať zelenou farbou. 2. NAPLŇTE PRAČKU PRÁDLOM. Otvore dvierka. Naplnte prácku prádlom, pricom dbajte, aby nedošlo k prekroceniu množstva náplne, uvedeného v tabulke programov na nasledujúcej strane. 3. DÁVKOVANIE PRACIEHO PROSTRIEDKU.
Programy a funkcie 6 - 6 1200 - 6 60° 800 3 40° 800 3 40° 800 3 30° 800 - - 3 1200 - 6 40° 30° - 800 0 1200 - - - PLÁKANIE (2. stlačenie tlačidla). - 1200 - - VYPÚŠŤANIE VODY (3. stlačenie tlačidla). - 0 - - Doba trvania cyklu 3 2,5 Voda celkom lt - Spotreba energie kWh SK Zvyšková vlhkosť % Max. náplň (kg) (3) Aviváž Bieliaci prostriedok Max.
Pracie prostriedky a prádlo SK Dávkovač pracích prostriedkov Dobrý výsledok prania závisí aj od správneho dávkovania pracieho prostriedku: použitie nadmerného množstva znižuje efektivitu prania a napomáha tvorbe vodného kameňa na vnútorných častiach práčky a zvyšuje znečistenie životného prostredia. ! Používajte práškové pracie prostriedky pre biele bavl- nené prádlo a pre predpieranie a pre pranie pri teplote vyššej ako 60 °C. ! Dodržujte pokyny uvedené na obale pracieho prostriedku.
Poruchy a spôsob ich odstránenia Môže sa stať, že práčka nebude fungovať. Skôr, ako zatelefonujete na Servisnú službu viď „Servisná služba“) skontrolujte, či sa nejedná o problém ľahko odstrániteľný pomocou nasledujúceho zoznamu. Poruchy: Pračku nie je možné zapnúť. Možné príčiny / Spôsob ich odstránenia: • Zástrčka nie je zasunutá v elektrickej zásuvke, alebo nie je zasunutá dostatočne, aby došlo k spojeniu kontaktov. • V celom dome je vypnutý prúd. Nedochádza k zahájeniu pracieho cyklu.
Servisná služba SK Pred obrátením sa na Servisnú službu: • Skontrolujte, či nie ste schopní poruchu odstrániť sami (viď „Poruchy a spôsob ich odstránenia“); • Opätovne uveďte do chodu prací program, s cieľom overiť, či bola porucha odstránená; • V opačnom prípade sa obráťte na Centrum servisnej služby, na telefónnom čísle uvedenom na záručnom liste. ! Nikdy sa neobracajte so žiadosťou o pomoc na technikov, ktorí nie sú na vykonávanie tejto činnosti oprávnení.
Instrucţiuni de folosire MAŞINĂ DE SPĂLAT RUFE Sumar RO Română RO Instalare, 38-39 Despachetare şi punere la nivel Racorduri hidraulice şi electrice Primul ciclu de spălare Date tehnice Întreţinere şi curăţare, 40 Întreruperea alimentării cu apă şi curent electric Curăţarea maşinii de spălat Curăţarea compartimentului pentru detergent Îngrijirea uşii şi a tamburului Curăţarea pompei Controlarea furtunului de alimentare cu apă Precauţii şi sfaturi, 41 FMSDN 623 Norme de protecţie şi siguranţă general
Instalare RO ! Este important să păstraţi acest manual pentru a-l putea consulta în orice moment. În caz de vânzare, de cesiune sau de schimbare a locuinţei, acesta trebuie să rămână împreună cu maşina de spălat pentru a informa noul proprietar cu privire la funcţionare şi la respectivele avertismente. ! Citiţi cu atenţie instrucţiunile: veţi găsi informaţii importante cu privire la instalare, la folosire şi la siguranţă. Despachetare şi punere la nivel Despachetare 1.
Conectarea furtunului de golire 65 - 100 cm Conectaţi furtunul de evacuare, fără al îndoi, la o conductă sau la o gură de evacuare în zid, situate între 65 şi 100 cm de pământ; sau sprijiniţil pe marginea unei chiuvete sau a unei căzi, legând elementul de ghidare la robinet (a se vedea figura). Capătul liber al furtunului de golire nu trebuie să rămână cufundat în apă.
Întreţinere şi curăţire RO Întreruperea alimentării cu apă şi curent electric • Închideţi robinetul de apă după fiecare spălare. Se limitează astfel uzura instalaţiei hidraulice a maşinii de spălat şi se elimină pericolul scurgerilor. • Scoateţi stecherul din priza de curent atunci când curăţaţi maşina de spălat şi când se efectuează lucrări de întreţinere. Curăţarea maşinii de spălat • Partea externă şi părţile din cauciuc pot fi curăţate cu o lavetă înmuiată în apă călduţă şi săpun.
Precauţii şi sfaturi ! Maşina de spălat a fost proiectată şi construită conform normelor internaţionale de protecţie. Aceste avertizări sunt furnizate din motive de siguranţă şi trebuie să fie citite cu atenţie. Siguranţa generală • Acest aparat a fost conceput exclusiv pentru utilizarea în locuinţe.
Descrierea maşinii de spălat RO Panoul de control Tastă Tastă ACŢIUNE CURĂŢARE ON/OFF Tastă CENTRIFUGARE DISPLAY Taste Sertarul detergenţilor SELECTARE PROGRAME Tastă cu led Tastă MY CYCLE Tastă TIP CLĂTIRE Tastă PORNIRE ÎNTÂRZIATĂ START/PAUSE Taste FUNCŢII Tastă TEMPERATURĂ Tastă BLOCARE TASTE Sertarul detergenţilor: pentru a introduce detergenţi sau aditivi (a se vedea “Detergenţi şi rufe albe”).
Display RO Z B A X D C E Y F Ecranul este util pentru a programa maşina şi a furniza numeroase informaţii. Pe cele două rânduri de sus, A şi B, apar programul de spălare ales, faza de spălare în curs de desfăşurare şi toate indicaţiile cu privire la stadiul de avansare a programului. Rândul C este dedicat timpului restant până la încheierea ciclului de spălare sau – dacă aţi programat pornirea maşinii la o anumită oră (PORNIRE ÎNTÂRZIATĂ) – timpul restant până la iniţierea spălării.
Cum se desfăşoară un ciclu de spălare RO 1. PUNEREA ÎN FUNCŢIUNE A MAŞINII. Apăsaţi tasta ; pe ecran va apărea mesajul PORNIRE ÎN CURS. Indicatorul START/PAUSE va emite un semnal intermitent de culoare verde. 2. INTRODUCEREA RUFELOR. Deschideţi uşa. Introduceţi rufele în maşină, fiind atenţi să nu depăşiţi cantitatea indicată în tabelul de programe (vezi pagina următoare). 3. DOZAREA DETERGENTULUI. Extrageţi sertarul şi turnaţi detergent în compartimentele respective, după indicaţiile din cap.
Programe şi funcţii Consum energie kWh Apă totală lt Durata ciclului de spalare - - 170’ 60’ 53 0,78 50 200’ 53 0,65 65 170’ - 170’ 44 0,70 40 105’ 44 0,47 38 95’ - 75’ 39 30’ - - 100’ - - - 65’ 75’ 10’ 36’ - - - 3’ Decolorant Balsam rufe Sarcina Max. (Kg) Umiditate reziduală% Viteza max. (rotaþii pe minut) Detergenþi Spãlare Descrierea Programului Temp. max.
Detergenţi şi rufe albe RO Compartimentul pentru detergenţi Programe optionale Un rezultat bun la spălare depinde şi de dozarea corectă a detergentului: excesul de detergent nu garantează o spălare mai eficientă, ci contribuie la deteriorarea părţilor interne ale maşinii de spălat şi la poluarea mediului înconjurător. ! Utilizaţi detergenţi praf pentru rufele albe de bumbac, pentru prespălare şi pentru spălarea la temperaturi mai mari de 60°C. ! Respectaţi indicaţiile de pe ambalajul detergentului.
Anomalii şi remedii Se poate întâmpla ca maşina de spălat să nu funcţioneze. Înainte de a apela serviciul de Service (a se vedea Asistenţă”), verificaţi dacă nu este vorba de o problemă uşor de rezolvat: Anomalii: Cauze posibile / Rezolvare: Maşina de spălat nu porneşte. • Stecherul nu este introdus în priza de curent, sau nu face contact. • Aveţi o pană de curent la domiciliu. Ciclul de spălare nu porneşte. • • • • • Uşa nu este bine închisă. Tasta ON/OFF nu a fost apăsată.
Asistenţă 195123911.00 04/2014 - Xerox Fabriano RO Înainte de a lua legătura cu Service-ul: • Verificaţi dacă puteţi rezolva singuri problema (a se vedea “Anomalii şi remedii”); • Porniţi din nou programul pentru a controla dacă inconvenientul a fost eliminat; • În caz negativ, luaţi legătura cu asistenţa tehnică autorizată la numărul telefonic indicat pe certificatul de garanţie. ! Nu apelaţi niciodată la persoane neautorizate. Comunicaţi: • tipul de anomalie; • modelul maşinii (Mod.