DAILY REFERENCE GUIDE FSCR80220 Max. Load: 8 kg Max. Spin Speed: 1200 rpm EN THANK YOU FOR BUYING A WHIRLPOOL PRODUCT. In order to receive a more complete assistance, please register your appliance on www.whirlpool.com.hk Before using the appliance, carefully read the Health & Safety, Use & Care and Installation guides. Before using the machine, it is imperative that the transport bolts are removed. For more detailed instructions on how to remove them, see the Installation Guide.
1. Main wash compartment • Detergent for the main wash • Stain remover • Water softener DETERGENT DISPENSER 2. Prewash compartment • Detergent for the prewash. 3. Softener compartment • Fabric softener • Liquid starch Pour in softener or starch solution only up to the “max” mark. 4. Release button (Press to remove the detergent dispenser for cleaning).
EN 3. OPEN THE WATER TAP 4. SWITCH ON THE WASHING MACHINE • Press the “On/Off” button until the programme button lights up. An animation appears on the control panel and the appliance plays a sound. The washing machine is then ready for operation. INDIVIDUAL MODE After you have switched on the washing machine, you are not forced to follow the GUIDED MODE. The order in which you choose to set your programme is up to you.
9. PAUSE A PROGRAMME WHICH IS RUNNING AND 11. SWITCH OFF THE WASHING MACHINE AFTER THE 10. RESET A PROGRAMME WHICH IS RUNNING, IF • Press “On/Off” to switch off the washing machine. The washing machine will switch off automatically after about a quarter of an hour after the programme ends, to save energy. • Leave the door ajar so that the inside of the washing machine can dry. OPEN THE DOOR, IF REQUIRED • Press and hold “Start/Pause” to pause a programme which is running.
EN DOSING AID To enable this function to calculate the detergent amount as precisely as possible, adapt the washing machine to the dosing values of the detergents you use, and also to your local water hardness.
To save these values in the washing machine: 1. Select the programme for which you want to save the detergent value . 3. Turn the knob to adjust the dosing value to the one you have identified before on the detergent pack . Afterwards confirm it by pressing the knob . 2. Press and hold the Dosing Aid button until the bottle symbol on the display lights up . The indicators of all programmes for the detergent group light up . % 4. Do this procedure for all three programme groups .
EN PROGRAMME CHART Cold-60°C 3.0 — DELICATES Cold-40°C 1.5 — — — WOOL Cold-40°C 1.0 — — — COLOURS Cold-60°C 4.0 Cold-30°C 3.0 — — — — RINSE&SPIN — max — — — — SPIN — max — — — — Programme RAPID 30’ 30’ Selectable/optional — — — — Not selectable/applicable With Rapid SYNTHETICS 60° C 06:00 04:00 — 60° C 02:20 01:40 max — Program Duration 4.0 Default Temp.
PROGRAMMES Observe the recommendations on the care labels of your laundry. ECO COTTON Normally soiled cotton laundry. Standard cotton programme. At 40°C and 60°C most favourable programme in terms of combined water and energy consumption for washing cotton laundry. The values on the energy label are based on this programme.
OPTIONS, FUNCTIONS AND INDICATORS OPTIONS which are directly selectable by pressing the dedicated button Colours 15° Helps to preserve the colours of your laundry by washing them with cold water (15°C). Saves energy used in heating the water, while maintaining good wash results. Suitable for lightly soiled coloured laundry without stains. Not selectable for Cotton 95°C. Fresh Care Helps to keep your laundry fresh if you cannot remove it from the machine shortly after the programme ends.
FUNCTIONS Rinse hold (option on Spin button) Avoids automatic spinning of the laundry at the end of the programme. The laundry remains in the last rinse water and the programme does not continue. Suitable for delicate laundry which is not suitable for spinning, or which should be spun with a lower spin speed. Not suitable for silk.
FSCR80220 最大洗衣量: 8 公斤 最高脫水轉速: 1200 轉/分鐘 日常使用參考指引 CH 感謝您購買惠而浦產品 為了獲得更完善的服務, 請於www.whirlpool.com.hk註冊您的產品 使用此產品前,請細心參閱 <產品安全指引、使用說明及安裝指南>。 使用此產品前, 必須拆除運輸螺栓。 有關如何拆除運輸螺栓的詳細說明, 請參閱<安裝指南>。 產品介紹 產品 1. 頂板 2. 洗衣劑盒 3. 控制面板 4. 機門門把 5. 機門 6. 底座後面的過濾器 及緊急排水喉(如有) 7. 底座 (可拆式) 8. 可調機腳 控制面板 1. 13. 12. 電源「開/關」鍵 (長按為「重設/排水」鍵) 2. 「程序」鍵 3. 「護色15°」鍵 4. 「清爽抗皺」鍵 5. 「洗衣劑計量助手」鍵 (長按為「設定」鍵) 6. MAX 30’ 60° 旋鈕 (旋動選擇 / 按壓確定) 7. 「預校開機時間」 鍵 40° 8. 「溫度」鍵 9. 「脫水轉速」鍵 10.「選項」鍵(長按此鍵為 「兒童安全鎖」功能) 11.「啟動/暫停」鍵 12. 顯示屏 1.
1. 主洗格 • 主洗用洗衣劑 • 去污劑 • 軟水劑 2. 預洗格 • 預洗用洗衣劑 3. 柔順劑格 • 衣物柔順劑 • 衣漿 添加劑只能添加到「MAX」標誌。 4.
CH 開啟水龍頭 3. 開啟洗衣機電源 4. • 按「開/關」鍵,直到「程序」鍵亮起。閃燈動畫 將會顯示,並且有聲響,代表該洗衣機已準備好被 使用。 設定所需的程序 5. 引導模式 - 指示燈會按以下順序引導您完成程序設 定:選擇程序/溫度/脫水轉速/選項。只要您按下旋 鈕確認選擇,指示燈會跳轉到下一個步驟。 • 選擇程序: 確保「程序」鍵亮起。 個人模式 當您已經開啟過洗衣機,您可以不用強制性跟著引導模 式使用。可按個人喜好選擇順序來設定程序。要進行設 定,首先按相應的按鍵,然後轉動旋鈕選擇,最後按下 旋鈕確認。 溫度,脫水轉速及選項的範圍取決於所選的程序。 因此,建議先設定所選擇的程序選項。 6.
暫停正在運行的程序及打開機門 (如有需要) 程序結束後關閉洗衣機 • 按下「啟動/暫停」鍵暫停程序。 • 顯示器上顯示程序結束「End」,而「開門」指示燈亦亮起。 – 您可以拿出機內衣物。 • 只要水位不太高,或機內衣物不太熱時,機門指示燈會 亮起。您可以打開機門,以添加或取走衣物。 • 再次關閉機門,並按下「啟動/暫停」鍵繼續運行程序。 重新設定正在運行的程序 (如有需要) • 按下電源「開/關」鍵,直到屏幕顯示 「rES」。 • 按電源「開 / 關」鍵,以關閉洗衣機。如果不將其 關閉,洗衣機將在程序結束的15分鐘後自動關閉, 以節省能源。 • 讓機門半開,使洗衣機的內部可以風乾。 洗衣水會被排走,程序結束及機門會被解鎖。 提示及應用 請根據以下建議分類衣物: 定期清潔濾網 • 衣料類型/護理標籤符號 (棉,混合纖維,合成纖維,羊毛,手洗項目) • 顏色 請將白色衣物與顏色衣物分開,並將簇新的顏色衣物分 開清洗。 • 纖細衣物 (清洗小件衣物,如尼龍絲襪;有鉤扣的衣 物,如胸罩及有拉鍊的布袋或枕套。) • 有助避免堵塞或無法正常排水。請參閱〈使
CH 洗衣劑計量助手 此功能可精確地計算洗衣劑量,將洗衣機對應 您所使用的洗衣劑量,及您居住地的水硬度。 儲存你所使用的洗衣劑的劑量值 洗衣劑類別: 顏色衣物 纖細衣物 通用 程序組別: 顏色衣物 羊毛,纖細衣物 所有其他程序 水硬度 檢查您的洗衣劑的包裝以得知「中度」的髒污 程度及水硬度「中」所需的劑量值。 髒污程度 軟 中 低 中 高 毫升 硬
儲存洗衣劑的劑量值: 根據所選用的洗衣劑的劑量值標示,轉動旋鈕來調整劑量值, 按下旋鈕以確認。 選擇您所需程序以儲存劑量值。 • 長按「洗衣劑計量助手」直至顯示屏上的圖案亮起, 其他所有相關程序組別的程序指示燈亦會亮起。 % 重覆以上步驟以設定三個程序組別,因此每一個程序組別只需 設定一次 - 程序組別內的所有程序便會自動設定。 回復原廠設定:轉動旋鈕來選擇「rES」及按下旋鈕以確認。 將洗衣機對應您居住地的水硬度。 洗衣機的預設水硬度是「軟」。 查詢您居住地區的水硬度,例如諮詢當地主管部 門或通過互聯網查詢。 – 如您居住地區的水硬度不是「軟」,根據下列 方法以設定洗衣機 : 設定水硬度 : 同時按住「程序」鍵及「洗衣劑計量助手」鍵。 轉動旋鈕來選擇水硬度至 2 = 「中」 3 = 「硬」 「1」顯示在顯示屏上,代表水硬度是「軟」。 按下旋鈕以確認。只要您確認水的硬度設定,您將自動 離開設定模式。
CH 程序表 羊毛 / 手洗 冷水-40° C 1.0 _ _ _ 顏色衣物 冷水-60° C 4.0 _ 冷水-30° C 3.0 _ _ _ _ _ _ 程序 使用快速 _ 程序時間 _ 預設 溫度及程序 時間(小時:分鐘) 溫度 冷水-40° C 1.5 柔順劑 纖細衣物 主洗 _ 洗衣劑 和添加劑 預洗 冷水-60° C 3.0 延遲脫水 合成纖維 脫水轉速 轉/分鐘 冷水-60° C 4.
程序 請參閱您的衣物護理標籤上的建議。 棉質節能洗 羊毛 / 手洗 適用於帶有羊毛標籤並標示可機洗的羊毛衣物,以及標 示手洗的絲(留意衣物標籤)、麻、羊毛及黏膠纖維織物。 適用於一般骯髒的棉質衣物。 40° 及 60° 水溫下清洗棉質衣物的最佳耗水 和耗電程序。屬能源標籤的參考程序。 30分鐘速洗 適用於較少污漬而由棉、合成纖維及混棉織物製成 的衣物。屬清新程序。 棉質 適用於一般或非常骯髒的毛巾、內衣褲、棉麻桌布及 床單等。 30’ 顏色衣物 適用於一般由棉、合成纖維或其混合物料及貼身 衣物。有助於保持衣物顏色。 60 分鐘混合洗 適用於由棉、麻、人造纖維及其混合織物製成的輕微 或一般骯髒的厚重衣物。屬高效一小時程序。 合成纖維 適用於一般骯髒的人造纖維衣物(例如滌綸、 綸、黏 膠纖維等)或混棉織物。 過水及脫水 過水及深度脫水程序。適合厚重衣物。 纖細衣物 適用於精緻面料製成,需要溫和呵護的衣物。 脫水 深度脫水程序。適合厚重衣物。 水電消耗資料表 由於不同條件因素(如:入水溫度,供水壓力等),各家庭的能源 消耗值可能會有不同。 程序 60 分鐘混合洗 溫度 (°C) 40
CH 選項,功能及指示燈 選項 - 控制面板的獨立選項 以下選項可按「選項」鍵選擇: 護色 15° 衣物將使用冷水(15° )洗滌,幫助保留衣服的顏色,也 可以節省用於加熱洗衣水的大部分電量,同時保持良好 的洗淨效果。 適用於有輕微骯髒的深色或彩色衣物。不適用於洗滌棉 質 95°。 預洗 在所選的洗衣程序上增加預洗程序,有助潔淨非常骯 髒的衣物。適用於非常骯髒的衣物,例如含有沙石 或顆粒狀污垢的衣物。延長洗衣程序約20分鐘。 需添加洗衣劑於洗衣劑盒的預洗格,或者直接倒入 滾桶。請使用洗衣粉於主洗格,以確保該洗衣粉停 留在洗衣劑盒,直到主洗階段開始。 清爽抗皺 有助於洗衣程序結束後無法即時取走衣物下,仍保持您 的衣服清新。 洗衣機將在程序結束後開始翻滾桶內衣物一段時間。這 翻滾時間可最長達約6小時。 您可以在任何時候任意按鍵停止,門會被解鎖,此時便 可拿出您的衣服。 洗衣劑計量助手 可以讓洗衣機針對您的洗衣量而顯示建議的洗衣劑量。 使用此功能前: 市場上可用的洗衣劑濃度各有不同。因此,把洗衣機設 定到您所使用的洗衣劑的合適劑量。此外,檢查洗衣機 的預設水硬度(軟)是否對應於您的居住地的水硬度, 必要時
功能 延遲脫水 (按「脫水轉速」鍵選擇此功能) 避免在程序結束時自動進行衣物脫水。 衣物留在最後一次過水的水中,顯示屏顯示延遲脫水, 程序不會繼續進行。 適用於不應旋轉清洗或應以低旋轉速清洗的纖細衣物, 但不適用於絲質衣物。結束「延遲脫水」功能,請按需 要選擇: • 排水不脫水 轉動旋鈕以選擇脫水轉速為「0」,然後按「啟動/暫 停」鍵。水會被抽乾排走,程序結束。 • 脫水 預設脫水轉速指示燈閃爍 - 「啟動/暫停」鍵開始脫水 程序。或轉動旋鈕選擇不同轉速,按一下確認,然後 按「啟動/暫停」鍵。 兒童安全鎖 鎖定控制面板,避免不必要的操作鍵和旋 鈕。 注意及操作如下: • 洗衣機必須處於開機狀態。 • 按下「選項」鍵,直到控制面板上的按鍵符號指示燈 亮起。 旋鈕和按鍵即被鎖定。只有「啟動/暫停」鍵可 如常運作。 如果關閉洗衣機後並再次啟動,兒童安全鎖將仍然保持 運作,直到您解開安全鎖才可繼續使用。 解鎖方法: 再次按住「選項」鍵至少3秒鐘,直到鑰匙符號燈熄滅。 指示燈 預校開機時間 將程序延遲至稍後時間開始。 請勿使用洗衣劑。 可以打開機門 • 選擇程序,溫度和選項。 • 按「預校開機時間 」鍵 -