Installation guide

ManualsBrandsWhirlpool ManualsDryerOfficial Whirlpool dryer

Havequestionsaboutyourdryer?

Check your Use and Care Guide for a toll+free number to call, or catl your

dealer. The dealer is listed in the Yellow Pages of your phone directory

under "Appliances -- Household -- Major -- Service and Repair:"

When you call, you will need the dryer model number and serial number:

Both numbers are on the model/serial rating plate located in the door well

behind the dryer door and on front of opening, +_/._

Record the numbers here for handy reference:

ModeB No+

Serial No+

o ?

Moving dryerto a newleeat+en.

Check with a licensed electrician to confirm that supply voltage at new home matches

voltage specified on the model/serial rating plate,

Shut off electrical

supply to dryer.

Unplug power supply

cord and tape it \

securely to dryer. _ _e top

(Or disconnect power \ to cabinet.

supply cable from

dryer,) _e door to

panel

Slide dryer onto cardboard or hardboard

before moving it across the floor to

prevent damaging floor covering.

Read and savethese instmetiens.

installer: Leave Installation Instructions with homeowner.

Hemeewner: Keep Installation Instructions for future reference.

Fer best perfermanee, install dryer according to

Installation Instructions+ Failure to complete installation

as instructed could void warranty.

Save Installation Instructions for local electrical inspector's use.

Summary of content (7 pages)

PAGE 1
Havequestions about yourdryer? Check your Use and Care Guide for a toll+free number to call, or catl your dealer. The dealer is listed in the Yellow Pages of your phone directory under "Appliances -- Household -- Major -- Service and Repair:" When you call, you will need the dryer model number Both numbers are on the model/serial rating plate behind the dryer door and on front of opening, Record the ModeB No+ Serial numbers here for handy and serial number: located in the door well +_/.
PAGE 2
Exhaust dimensieas back exhaast 0 r> 0 strain re[ief The dryer door extends 14" from the front of the dryer when fully opened. 43-1/8" Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer, Place dryer at [east 18 inches above the floorfora garage installation. Faiture to do so can result in death, explosion, or fire, J /r-,_ 14-1/8" 2%1/4"* (models with fluslmounted 30-1/4"* door handle) (models wRh extended door handle) \ _27" bettem at least 5" clearance
PAGE 3
Dura Safe TM venting products and are available from your Fourdnch diameter Use a heavy foil vent. o Do Not hoods vent metal must vent. flexible magnetic M@iie heme [nstaiJatienrequirements be used. Do Not use non°meta[ with are recommended deaJero use plastic vent, or metal Safety Standard, Federal Standard or exhaust Iatches. Do Not exhaust dryer into a chimney, wail, ceiling, furnace, coM air vent, duct, concealed space, attic or craw[ space, or any other vent used for venting.
PAGE 4
I Put on safety Install Connect vent to exhaust hood with 4" clamp. (Exhaust vent MUST fit inside hoodO glasses and gloves. exhaust hood. Run exhaust vent to dryer location. Use the straightest path possible. (See Panel B.) Use clamps to secure vent pieces, Tin snips may be needed to cut vent to required length, Use caulking compound to seal -exterior wall opening around exhaust hood. Excessive Weight Hazard Use two or more people to move and install dryer.
PAGE 5
14-30R Four-wire receptacle (required for 4. Remove center terminal block screw. "X 6. Connect the ground wire (bare) of the power supply cable to the external ground conductor" screw. Tighten _ _ __ n _' n mobile homes) 5. Remove appliance ground wire (green with yellow stripes) from external ground connector screw. Fasten under center, silver-colored terminal block screw. / _ / n d +r) screw, Direct wire cable [ _ / // 8.
PAGE 6
WhereMe€aM codesDoNet permit 5. connecting cabinet=ground conductor to neutral wire: [] []urn Three°wke 4. power suppBy cord must four feet long and have three, NoM copper wires and match a three°wire receptacle of NEMA Type ] 0=30R be Remove center terminal block screw. 6. Connect the other wires to outer terminal block screws. Tighten screws. 0 Remove ground stripes) ground Connect and the the appliance wire (green with yellow from the external connector screw.
PAGE 7
Partssupplied: Your safety and the safety of others is very important. Remove We have provided many important safety messages in this manual and on your appliance=Always read and obey all safety messages= ] parts package dryer drum. Check legs were included.