Installation guide

Before you start...
Proper installation is the installer's
responsibility. A qualified technician should
install this microwave oven hood. Make
sure you have everything necessary for
correct installation. It isthe responsibility of
the installer to comply with the installation
clearances specified either on the
mounting bracket or in the Installation
Instructions.
This microwave oven hood is shipped
assembled for ventless (recirculating)
installation.
I CRITICAL
DIMENSION
Important: Observe all
governing codes and
ordinances.
Remove all
contents from
the upper
cabinet. ,
i
-- 30"rain. cabinet
opening width
16"
i
Electrical ground is
required. See "Electrical
requirements," Panel B.
30" rain. to top of wall
mounting bracket
Excessive Microwave Energy Exposure
Do Not attempt to operate this microwave
oven with the door open.
Do Not tamper with or defeat the safety
interlocks.
Do Not place objects between the
microwave oven front face and the door.
Do Not allow soil or cleaner residue to
accumulate on sealing surface of
microwave oven door.
Do Not operate microwave oven if it is
damaged.
The microwave oven door must close
properly to provide safe operation. Do Not
usa microwave oven if door is bent;
hinges and latches are broken or loose; or
door seals, sealing surfaces or glass is
broken.
The microwave oven should be adjusted
and repaired only by a qualified repair
:)erson.
Have a qualified repair person check for
microwave leakage if a repair is made.
Do Not use microwave oven for
commercial purposes. This microwave
oven is designed for household use only.
Failure to use microwave oven except as
instructed could result in exposure to
excessive microwave energy.
This product issuitable
for use above electric
and gas cooking
products 30" wide
or less,
Wall construction should be a minimum of
2" x 4" wood studding and 3/8" thickness
drywall or plaster/lath.
Check the microwave oven for damage.
Remove all packaging material from inside
microwave oven. See WARNING for
excessive microwave energy exposure. If
any damage is evident, Do Not operate the
microwave oven until it is checked by an
authorized service technician.
Place a portion of carton or another heavy
material over the countertop and range
before installing the microwave oven hood.
Do Not use a plastic cover.
Parts supplied
for installation:
4, I/4" x 3" bolts
4, 1/4"x2"lag screws
2 tapping screws
(bright-colored)
4 spring toggle-heads
I power supply cord
clamp and I
mounting screw
(dark-colored)
00
2 washers
2 filters
I power supply
cord bushing
I lock pin and
I" outside diameter x 5/16"
inside diameter washer
Check location:
• The wall must be strong enough to
support the microwave oven hood
weight of 150 pounds, plus the weight of
any items placed inside the microwave
oven or the upper cabinet.
° The location should be away from draft
areas, such as windows, doors, and strong
heating vents.
° The microwave oven hood should be
located for convenient use in the kitchen.
Tools and materials
needed for
installation:
No. 3 Phillips
screwdriver
carton or another
heavy material
for covering
counteffop
studfinder or
thin nail
electric drill
flat-blade
screwdriver
318" and 314"
wood drill bits
3116" drill bit
gloves
Electrical Shock Hazard
It is the customer's responsibility:
To contact a qualified electrical installer,
To assure that the electrical installation is
adequate and in conformance with
National Electrical Code, ANSI/NFPA 70 --
latest edition*, and all local codas and
ordinances.
To correctly drill holes into the wall.
Electrical wires may be concealed behind
the wall covering and contact with them
could result in electrical shock.
To locate any electrical circuits that could
be affected by the installation of this
_roduct and disconnect power circuit.
Failure to follow these instructions could
result in death or serious injury.
Injury Hazard
Two people are required to lift this
microwave oven hood.
Failure to use more than one person
during installation may result in injury.
This microwave oven hood must be
mounted against and supported by a flat,
vertical wall.
This microwave oven hood must be
attached with two lag screws to a
minimum of one, vertical 2" x 4" wall stud.
Do Not mount microwave oven hood to an
island or peninsula cabinet.
The top and rear supporting structure for
microwave oven hood must be capable of
supporting 150 pounds, plus the weight of
any items placed inside the microwave
oven or upper cabinet.
Failure to mount the microwave oven
hood as instructed could result in injury.
Copies of the standard listed may be
obtained from:
*National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
caulking gun and
weatherproof
caulking
compound
small side
cuttersor
finsnips
Special hardware and tools are required for
brick or masonry walls,
Panel A