Installation guide

D Electricalconnection
Electrical Shock Hazard
Disconnectpower to the junction box before
making connection.
Electrically ground oven.
Connect ground with t0-gauge-minimum solid
copper wire.
Failure tofollow these instructionscould result
in death, fire or electrical shock.
This oven is manufactured with white (neutral)
power supply wire and a cabinet-connected bare
grounding wire twisted together.
Feedoven cablethrough opening in
• the cabinet. Make electrical connection
following the steps neededfor your installation.
1. Disconnectthe power supply.
2. Remove the junction box cover.
3. Connectoven cable to junction box through the
U.L.-listedconduit connector,
4. Connect the two blackwires together with
twist-on connectors,
5. Connect the two red wires together with
twist-on connectors,
6. Complete electrical connection according to
local codes and ordinances.
junction
box
r_h_.2e_
wires
W
wire
grounding oven
cable wires
factory crimped
Figure 1
cablefrom
power supply
cable from conduit
oven connector
If local codes PERMIT
connecting cabinet-grounding
conductor to neutral white
wire in junction box:
7. Connect the factory-crimped bare
and white oven cable wires to
the neutral (white) wire in
junction box. See Figure 1.
8. Replace junction box cover.
cablefrom
junction power supply
box
re; .w,i;:
k wires
bare grounding _ /
w,res _"_U ,L.-listedconduit
Figu re 2 cablefrom connector
oven
If local codes DO NOT PERMIT
connecting cabinet-grounding
conductor to neutral white
wire in junction box:
7. Separate the factory-crimped
bare and white oven cable wires.
8, Connect white oven cable wire to
neutral (white) wire in junction
box. See Figure 2,
9, Connect the bare grounding
oven cable wire to a grounded
wire in the junction box, See
Figure 2.
10. Replace junction box cover,
If connecting to a
four-wire electrical system:
7. Separate bare andwhite
oven cable wires,
8, Connect white oven cable wire to
neutral (white) wire in junction
box. See Figure 2.
9, Connect the bare grounding oven
cable wire to the green grounding
wire in junction box. Do Not
connectbare groundingwire to
neutral (white} wire in junction
box.See Figure 2.
10. Replacejunction box cover.
Attachment
Carefully push against seal area of oven front
frame when pushing oven into cabinet.
Do Not push against outside edges.
• Lift oven into cabinet cutout using the
oven opening as an areato grip.
shL"ogn'
Push against seal area of front frame to push
oven into cabinet until shipping feet almost
contact cabinet. Use a Phillips screwdriver to
remove screws attaching shipping feet, Remove
and discard shipping feet.
Push oven completely into cabinet and center
oven in cabinet cutout,
14screws
• Important: Securely fasten oven to cabinet
using the screws provided (two screws for a single
oven or four screws for a double oven). Insert the
screws through holes in mounting rails. Do Not
overtighten screws.
Pushtrim
into place.Replace
trim screw•
= Slide top end of each trim upward onto oven
side rails. Push each trim into place at bottom of
trim. Use screws to attach each trim to oven. Take
care not to scratch other surfaces with ends of trim.
• Replace oven racks.
oven frame
door
hinge
Replacethe lower oven door by inserting
• ends of hinges into hinge slots in oven
frame. Push behind each hinge so that hinges are
pushed into oven frame as far as they will go. Open
door and remove both door removal pins. Close
and open door to check that door closes and opens
completely. If door does not close or open
completely,you have not pushed hinges
completely into frame. Repeatdoor removal step
and reinsert door into hingeslots again.
D Check operation
0 = Turn on power supply, The display
panel will light up briefly. "PF" should appear in
the temperature display.
Make sure the oven door isclosed and the "ON"
light is shown in the display area. After 2 minutes,
partially open oven door. You should feel heat from
the oven. Press the "CANCEL" pad.
If your oven does not heat or an"F" appears in
the display, contact your dealer or check the "If
you need service..." section of this Installation
Instructions.
IB'KliBOLIICLE'N1
n • Checkthe operation of your lower
1
oven. Pressthe "BROIL" pad, "BROIL" will
appear in the display. Press the "START" pad,
2. Checkthe operation of the
microwave oven.
• Fill a microwave-safe container with one cup of
water and place containerinside microwave oven.
Close doorfirmly.
• Set microwave oven cooktime to "2:00"
minutes,
• Pressthe "START/ENTER" pad. The interior
microwaveoven light shouldbe on and the
remaining cooking time should be displayed.
Page 3
• When display reads "1:00," open microwave
oven door, The microwave should stop cooking.
• Close door firmly. The interior microwave oven
light should turn off.
• Press the "START/ENTER" pad. Microwave oven
should begin cooking and the microwave oven
interior light should be on.
• Let microwave oven complete cooking time. A
tone will sound four times at end of cooking time
and microwave oven will shut off.
• Open microwave oven door and carefully remove
container. Water in container should be hot.
To get the most efficient use
from your new oven, read your
Use and Care Guide. Keep
Installation Instructions
and Guide close to oven
for easy reference.