Installation guide

Beforeyoustart...
Your safety and the safety of
others are very important.
We have provided many important
safety messages in this manual and
on your appliance. Always read and
obey all safety messages.
This is the safety alert
symbol.
This symbol alerts you to
potential hazards that can kilt or hurt
you and others.
All safety messages will
safety alert symbol and either the
word "DANGER" or "WARNING".
These words mean:
You Can be killed or seriously
injured if you don't immediately
follow instructions.
You can be killed or seriously
injured if you don't follow
instructions.
All safety messages will tell you
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen ifthe
instructions are not followed.
Read electrical and carpentry
instructions.
Proper installation is your
responsibility. A qualified technician
must install this range. Make sure you
have everything necessary for correct
installation. It is the customer's
responsibility to make sure that the
countertop has been properly prepared
and that the installation clearances
specified on the model/serial rating
plate are met. The model/serial rating
plate is located on the oven frame
behind the drawer.
Check location where range will be
installed. The range should be located
for convenient use in the kitchen.
Recessed installations must provide
complete enclosure of the sides and
rear of range.
ALL OPENINGS iN THE WALL OR
FLOOR WHERE RANGE iS TO BE
INSTALLED MUST BE SEALED.
IMPORTANT: Some cabinet and
building materials are not designed to
withstand the heat produced by the
oven for baking and self-cleaning.
Check with your builder or cabinet
supplier to make sure that the materials
used will not discolor, delaminate or
sustain other damage.
It is the customer's responsibility:
To contact a qualified electrical
installer.
Mobile home installation
The installationof this range must
conform to the Manufactured Home
Construction and Safety Standards, Title
24 CFR, Part 3280 (formerly the Federal
Standard for Mobile Home Construction
and Safety, Title 24, HUD, Part 280); or
when such standard is not applicable, the
Standard for Manufactured Homes
Installations (Manufactured Home Sites,
Communities and Setups), ANSI
A225.1/NFPA 501A, or with local codes*.
in Canada, the installationof this range
must conform with the current standards
CAN/CSA-Z240 -- latest edition**, or with
local codes.
When this range isinstalled ina mobile
home, it must be secured to the floor
during transit. Any method of securing the
range is adequate as long as it conforms
to the standards listed above.
Four-wire power supply cable must be
used in a mobile home installation. The
appliance wiring will need to be revised.
See four-wire electrical connection,
Page ?.
Copies of the standards listed may be obtained
from:
* National Fire Protection Association
Satterymarch Park
Quincy, Massachusetts 02269
** CSA International
8501 East Pleasant Valley Road
Cleveland, Ohio 44131.5575
Important: Observe all governing
codes and ordinances.
When installinga range under existing
cabinets and the installation does not
meet the minimum cabinet clearances,
install a range hood above the cooktop
to avoid burn hazards.
Grounded electrical outlet is required.
See "Electrical requirements:' Panel B.
Cabinet opening dimensions that are
shown must be used. Given dimensions
are minimum clearances.
Do Not pinch the power supply cord
between the range and the wall.
Do Not seal range to side cabinets.
To assure that the electrical
installation is adiquate and in
conformance with National Electrical
Code, ANSI/NFPA 70 -- latest
edition*, or CSA Standard C22.1,
Canadian Electrical Code, Part 1 --
latest edition**, and all local codes
and ordinances.
Note: The metal chassis of the range
MUST be grounded in order for the
control panel to work. !f the metal chassis
of the range is not grounded, NO keypads
wilt operate. Check with a qualified
electrician if you are in doubt as to
whether the metal chassis of range is
Partssu
• .ppliedfor
installation:
_: bracket
'_ .W_._.'_ . plastic
aec,eo
(#tox1.1/2"1
(Bracket must be securely mounted to sub-
floor. Thickness of flooring may require longer
grounded, screws to anchor the bracket to sub-floor.)
Toolsneededfor installation: _ 'i level hand or electric drill
• wood floor: 1/8" drill bit
_ ruler or .F-_t_ fl -I " _'///_"" • concrete/ceramic floor:
/_ tape measure _ sca_e°wlz_°ever _/_chet 3116" carbide-tipped
Phillips _ _ _ _ _, -l_r/, i/_...Jv safety
screwdriver _ - I "_ glasses
2 gloves