Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersGSI 4619 POWER IN

-1-

Chart

START

DELAY

option

ON/OFF

BUTTON

PROGRAM

SELECTOR

KNOB

(see “Table of

programs”

below).

START BUTTON

The indicator lights up during operation, flashes when a fault occurs, and goes off

at the end of the program.

START BUTTON RESET FUNCTION:

Press this button for at least 2 seconds; the selected program and options will be

cancelled. Main failure displays (repeated flashing of the START indicator lamp) can be

cancelled by RESETTING. Detailed instructions are given in chapter “What to do if...”.

(see at right for options description)

MULTI

ZONE

option

POWER

CLEAN

option

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional

options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of th

appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on th

EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

Table of programs

Deter-

gent

Consumption

Programs

Available

options

Loading instructions

Litres kWh

Minutes

Sensor Intensive 60-70°C

Delay

Multizone

Power Clean

Automatic program recommended for heavily

soiled crockery with dried-on or burnt food, for

example pans and saucepans. Thanks to steam

action, soaking or hand pre treatment is no

longer needed. In addition sanitation is ensured

due to the high temperature steam.

X 13-20 1.10-2.00 100-150

Pre-Wash cold

Delay

Multizone

Crockery to be washed later. — 4.0 0.03 14

Quickwash 45°C

Delay

Multizone

Lightly soiled crockery, with no dried-on food.

* Use of tablets not recommended.

11.0 0.80 30

Bio Normal

50°C

Delay

Multizone

Power Clean

Normally soiled crockery.

Energy-saving program.

X 12.0 1.05 165

Hygienic +

Delay

Multizone

Normally or heavily soiled crockery, with

additional antibacterial wash. Program

interruption (e.g. due to door opening) can

compromise elimination of germs.

X 13.0 1.50 115

Intensive 70°C

Delay

Multizone

Power Clean

Recommended program for heavily soiled

crockery, especially suitable for pots and pans.

X 14.0 1.55 155

5019 496 01653GSI 4619 POWER

DELAYED START

BUTTON

Press the button

(repeatedly) to delay the

start of the program.

Adjustable from 1 to 24

hours. With each press of

the button, the delayed

start indicator increases by

one hour and after 24

restarts from 00. Then

press the START button.

The dishwasher will start

after the set time.

RINSE AID INDICATOR

When lit, the rinse aid dispenser

needs to be refilled.

SALT INDICATOR

When lit, the salt reservoir

needs to be refilled.

FAULT INDICATION AND WASH TIME DISPLAY

In normal operation it indicates the remaining time

(h:mm), whereas with “Delayed start” selected it

indicates the time remaining until program start (hh).

If “F..” appears on the display, see chapter “What to do if...”.

Options and display description

BEFORE USING THE APPLIANCE FOR THE

FIRST TIME CAREFULLY READ THIS QUICK

REFERENCE GUIDE AND THE ASSEMBLY

INSTRUCTIONS! THE GUARANTEE IS NOT

APPLICABLE IF FAULTS ARE CAUSED BY

INCORRECT USE OF THE APPLIANCE.

HALF LOAD/

MULTIZONE

Allows you to choose the

washing zones. Press this

button to select the wash

zones:

both racks

only upper rack

only lower rack

POWER CLEAN

Thanks to the additional

power jets this option

provides a more intensive

and powerful wash in the

lower rack, in the specific

area.This option is

recommended for washing

pots and casseroles

(see

page 4). Press this button

to activate Power Clean

(the indicator lights up).

Quick reference guide

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! THE GUARANTEE IS NOT APPLICABLE IF FAULTS ARE CAUSED BY INCORRECT USE OF THE APPLIANCE. Options and display description PROGRAM SELECTOR KNOB (see “Table of programs” below). START BUTTON The indicator lights up during operation, flashes when a fault occurs, and goes off at the end of the program.
PAGE 2
First time use How to set detergent type: powder/gel/tablet (if option is available) In order to always ensure the best cleaning results, you NEED to set: DETERGENT type and WATER HARDNESS. 1. Select 3rd program (see 2. Press START button 3a. Check your Table of programs - page 1) for 7 seconds detergent type... Detergent types Powder or gel (factory setting) 3b....and set it on your dishwasher using the START button (as per table below) 4.
PAGE 3
Daily check Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!) 1 Visual indicator (depending on model). Unscrew cap. Add salt (never add detergent!). min. 0.8 kg max. 1 kg Fill the salt reservoir with water before the first wash only. (depending on the model) Salt indicator on the control panel The salt level indicator lamp may remain lit for the duration of several wash cycles.
PAGE 4
How to load the racks How to load UPPER RACK 4 (In some models only) A - Multipurpose support: Different positions for long utensils, cups and glasses. B - Adjustable flaps: In horizontal position for cups/long utensils, in raised position for plates and stemware. How to adjust upper rack height (if available) - It could be useful to lift up upper rack to have more space in lower rack or bring it down to load long stem glasses.
PAGE 5
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open.
PAGE 6
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... ...is not working/will not start ...shows “F1” on the display or the START indicator lamp flashes once ...shows “F4” on the display or the START indicator lamp flashes 4 times ...
PAGE 7
What to do if... Crockery and cutlery... ...salt indicator lit ...have deposits: regeneration salt residue ...are not dry Possible causes... Solutions... - Use tablets for soft water. - Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up. - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly.
PAGE 8
Disconnect the mains plug What to do if... If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1.