Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersGSI 5964 IN

EN -1-

Chart

(see at right for options description)

PROGRAM SELECTION

BUTTON

Push “P” button (repeatedly)

until selected program number

is shown on the display

(P1...Px) - see “Table of

programs” below.

START/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the

program.

When the door is opened during a washing cycle,

the cycle is temporarily paused: the Start indicator

blinks. To resume the cycle close the door and

push Start button again.

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on conditions.

Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard

loading comparison test and other tests, contact (only in English) use following address “contact@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

RECYCLING WATER SYSTEM: these programs save water in a dedicated tank.

A TANK CLEANING CYCLE (at least 45 min.) is automatically run every 30 cycles or after every power off, to assure the best product conditions.

* Power consumption in: Left-on mode: 0,70 W. Off-mode: 0.40 W.

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs

Available

options

Loading instructions

Litres kWh

Minutes

Sensor Power

Clean Plus

40°-70°C

Delay

Antibacterial

rinse

Power Clean

Use for normal soiled dishes with dried-on

food. Senses the level of soiling on the

dishes and adjusts the program accordingly.

When the sensor is detecting the soil level

an animation appears in the display and the

cycle duration is updated. The Power Clean

option is activated automatically with this

program. To deactivate, press the Power

Clean button on the control panel.

X 7-15 1.00-1.70 70-172 Full

Pre-Wash cold

Delay Crockery to be washed later. – 4.0 0.01 14-16 NO

Glass 40°C

Delay Light soiling, for example glasses and cups. X 10.5 0.85 105-114 Light

Express 45°C

Delay

Lightly soiled crockery, with no dried-on

food.

X 11.0 0.85 30-50 NO

Eco

50°C

Delay

Antibacterial

rinse

Power Clean

Normally soiled crockery.

Standard program, the most efficient in

terms of its combined energy and water

consumption.

X 6.0 1.03 185 Full

Normal 60°C

Delay

Antibacterial

rinse

Normally soiled crockery. X 11.0 1.30 80-95 Full

Half Load 50°C

Delay

Ideal for washing a half load of lightly or

normally soiled crockery.

X 7.5 1.00 75-80 Full

Intensive 65°C

Delay

Antibacterial

rinse

Power Clean

Recommended program for heavily soiled

crockery, especially suitable for pans and

saucepans.

X 11.0 1.60 165-175 Full

5019 400 00171

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ

THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Options and display description

SALT INDICATOR

When lit (at the end of the cycle),

the salt reservoir needs to be

refilled.

RINSE AID INDICATOR

When lit (at the end of the cycle),

the rinse aid dispenser needs to

be refilled.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates

the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING

ANY BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES

AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

POWER CLEAN

Thanks to the additional power

jets this option provides a more

intensive and powerful wash in

the lower rack, in the specific

area. This option is

recommended for washing pots

and casseroles (see page 4). Press

this button to activate Power

Clean (the indicator lights up).

For non Power Clean loading

to achieve best cleaning

performances and resources

optimization, Power Clean should

be switched off.

TABLET SETTING

This setting allows to

optimize the cycle

performances according

the type of detergent used.

Push the Tablet button for

3 seconds (until the

indicator lights up) if you

are using the combined

detergents in tablet (rinse

aid, salt and detergent in 1

dose).

If you are using powder

detergent or liquid

detergent, the Tablet

indicator on the control

panel has to be off.

DELAYED START

BUTTON

Push the button

(repeatedly) to delay the

start of the program.

Adjustable from 1 to 24

hours. With each press of

the button, the delayed

start indicator increases by

one hour and after

24 restarts from 0. Then

press the START button.

The dishwasher will start

after the set time.

ANTIBACTERIAL RINSE

This function activates an antibacterial rinse

at the end of the wash cycle, guaranteeing

a further reduction of bacteria. Press the

button to activate or deactivate the

function. This function can be used with the

programs indicated in the table of

programs. The dishwasher door must be

kept shut for the entire duration of the

program in order to guarantee reduction of

bacteria. If the door is opened the indicator

lamp starts flashing.

Quick reference guide

Bauknecht is a registered trademark

Summary of content (8 pages)

PAGE 1
Chart Quick reference guide BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS! (see at right for options description) PROGRAM SELECTION BUTTON Push “P” button (repeatedly) until selected program number is shown on the display (P1...Px) - see “Table of programs” below. START/RESUME BUTTON Push this button to start the selected program: the indicator lights up and goes off at the end of the program.
PAGE 2
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only before the first wash or if water hardness has been changed - Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds. - The current water hardness setting will be visible on the display. - Press the PROGRAM Selection button to increase setting.
PAGE 3
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator 2 Visual indicator If required, open the cover B (press the dedicated button). Check the rinse aid indicator to check the level into the dispenser. The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B.
PAGE 4
How to load the racks UPPER RACK - depending on the model 4 A - Adjustable flaps (2 or 4): in horizontal position for cups/long utensils/stemmed glasses. A - CLOSED A - OPEN TO OPEN A: B - Cutlery basket: can be placed in the upper rack when the “Half load/Multizone” option is selected. The Grid (F) should be removed. CLICK! How to adjust upper rack height (if available). It could be useful to lift up the upper rack to have more space in lower rack or bring it down to load long stem glasses.
PAGE 5
Select program 6 Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. Wash cycle 7 The dishwasher door must be closed and the water tap open. To pause the program (e.g.
PAGE 6
What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. How the faults are shown on the display: Function number “F”x - blinking The appliance... ...is not working/will not start - The appliance must be switched on. - Check the household circuit fuse if there is no power supply.
PAGE 7
What to do if... Crockery and cutlery... Possible causes... Solutions... ...salt indicator lit - Use tablets for soft water. - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up. ...have deposits: regeneration salt residue - Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water hardness”). - Salt reservoir cap open. - Close the salt reservoir cap properly. ...
PAGE 8
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side: Precautions and general recommendations 1.