Instruction for Use

1
GB
Before using the dishwasher, read the
installation and maintenance instructions carefully!
5019 496 01102
GSI 5570
1) Program data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g. different loads,
options, different sensor settings (only with sensor programmes), different water supply temperatures, as well as water hardness
and power supply voltage.
2) Energy label programme in compliance with EN 50242. - Information for Test Laboratories:
for more detailed information on
the EN comparison test and other tests, contact the following address: “[e-mail]”.
3) The antibacterial action has been shown in collaboration with the Pasteur Institute, Lille (France), in conformity with.
Standard NF EN 13697 - November 2001.
1. OVERVIEW
Programme selector
START button
Switches “on” when the dishwasher is operating. Flashes when a
fault occurs. Switches off at the end of the programme.
START button RESET function:
Press this button for at least 2 seconds; the selected programme
and options are cancelled. Main failure displays (repeated flashing
of the START indicator lamp) can be cancelled by RESETTING.
Detailed instructions are given in chapter 5 “What to do if...”.
Rinse aid level indicator and salt level indicator
They light up when rinse aid or salt need to be added.
Add just before starting a wash cycle.
Fault indication and wash time display
With normal operation, the display indicates residual time (h:mm),
while with the “Delayed start” function selected it indicates time
remaining until the start of the programme (hh).
If “F..” appears on the display, see chapter 5 “What to do if...”.
Detergent setting upon initial use and when using a different type of detergent
1. Select the third programme in the relative table.
2. Press the START button for approx. 7 sec. to change the display.
3. Using the START button, select the desired detergent:
Display shows: 2 -1 = 2 in 1, 3 -1 = 3 in 1, 4 -1 = other combined action
detergents (in this way, the rinse aid and/or salt indicator is deactivated).
Display shows OFF = Powder detergent (factory setting).
(rinse aid level and salt level indicator activated).
4. Switch the appliance off and then switch it on again. The selected detergent
type will be indicated on the display for approx. 3 seconds.
“Delayed start” button
Press the button as required to delay the start of the programme.
Adjustable from 1 to 24 hours. With each press of the button, the
delayed start indicator increases by one hour and after 24 restarts
from 00. Then press the START button. The dishwasher will start
after the set time.
Half Load / Multizone Button”
The half load cycle can be used for the upper or lower rack. Select
the required programme then press the “Half load” button. The
light comes on and goes off at the end of the programme.
This function can be used with the programmes indicated in table 1.1.
Antibacterial rinse
3)
This function activates an antibacterial rinse at the end of the wash
cycle, guaranteeing a further reduction of bacteria. Press the button to
activate or deactivate the function. This function can be used with
those programmes marked with the relative symbol in table 1.1.
The dishwasher door must be kept shut for the entire duration of
the programme in order to guarantee reduction of bacteria. If the
door is opened the indicator lamp starts flashing.
On / Off Button
Table 1.1.
Table of programmes
Detergent
dispenser
Consumption
1)
P
Programmes
Available
options
Loading instructions
large small Litres kWh Minutes
1
Pre-Rinse cold
— Crockery to be washed later. — — 4.0 0.03 14 ±
1)
2
Quickwash 40°C
—
Lightly soiled crockery, without dry
residuals.
X — 10.0 0.65 30 ±
1)
3
Bio
2)
50°C
Normally soiled crockery. Energy-saving
programme.
X X 12.0 1.05 165 ±
1)
4
Daily 60°C
Normally or heavily soiled crockery. X X 13.0 1.25 120 ±
1)
5
Intensive 70°C
Recommended programme for heavily
soiled crockery, especially suitable for
pans and saucepans.
X X 14.0 1.55 155 ±
1)