Instruction for Use

ManualsBrandsWhirlpool ManualsDomestic AppliancesGSI 5991/1 IN LCD

5019 496 01099

GSI 5991

Before using the dishwasher, read the

installation and maintenance instructions carefully!

1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to different loads, extra

functions, sensor settings (only with sensor programmes), water supply temperatures, water hardness and power supply voltage.

2) Energy label programme in compliance with EN 50242. - Information for Test Laboratories:

for more detailed information on the EN comparison test and

other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on Standard NF EN 13697 - November 2001.

1. OVERVIEW

Programme selector

START button

The indicator lights up during operation, flashes when a fault

occurs, and goes off at the end of the programme.

START button RESET function:

Press this button for at least 2 seconds; the selected programme

and options are cancelled. Main failure displays (repeated flashing

of the START indicator lamp) can be cancelled by RESETTING.

Detailed instructions are given in chapter 5 “What to do if...”.

Power Clean

High pressure with an additional jet for better washing results and

greater bottom rack load flexibility.

When this option is selected, the display shows the corresponding

symbol.

Detergent setting upon initial use and when using a different type of detergent

1. Select the third programme in the relative table.

2. Press the START button for approx. 7 sec. to change the display.

3. Using the START button, select the desired detergent:

Display shows: no symbol = powder detergent (factory setting)

(rinse aid and/or salt indicator on)

= 2 in 1

= 3 in 1 or other combined action detergents

(In this way, the rinse aid and/or salt indicator is deactivated)

4. Switch the appliance off and then switch it on again. The type of detergent

selected will be shown on the display.

Fault indication and wash time display

In normal operation it indicates the remaining time (h:mm),

whereas with “Delayed start” selected it indicates the time

remaining until programme start (hh).

If “F..” appears on the display, see chapter 5 “What to do if...”.

Delayed Start button

Press the button (repeatedly) to delay the start of the programme.

Adjustable from 1 to 24 hours. With each press of the button, the

delayed start indicator increases by one hour and after 24 restarts

from 00. Then press the START button. The dishwasher will start

after the set time.

Programme sequence indicator

Rinse aid level indicator and salt level indicator

These indicator lamps light up when rinse aid or salt need to be added.

Add just before starting a wash cycle.

Half Load/Multizone button

Load the upper or lower rack only.

Press once = wash upper rack (the indicator/symbol lights up)

Press twice = wash lower rack (the indicator/symbol lights up)

Press 3 times = Off (Half load/Multizone deactivated).

When washing without the upper rack, press the “Half load” (i.e.

“wash lower rack”) button twice, (the corresponding indicator/

symbol lights up).

On / Off button

Prewash Washing Drying

Table 1.1.

Programme chart

Detergent

dispenser

Consumption

Programmes

Available

options

Loading instructions

large small Litres kWh Minutes

40-70°C

Normally or heavily soiled crockery, including pots

and pans.

X X 7-17 0.99-1.75 65-220 ±

Pre-Rinse cold

Crockery to be washed later.

— — 4.0 0.03 14 ±

Glasses 40°C

Lightly soiled, e.g. glasses and cups, with a lower

pressure jet.

X — 10.0 0.85 100 ±

Quickwash 40°C

Lightly soiled crockery, with no dried-on food.

X — 10.0 0.65 30 ±

Bio

50°C

Normally soiled crockery. Energy-saving

programme with prolonged drying.

X X 13.0 0.93 200 ±

Hygienic +

Normally or heavily soiled crockery, with

additional antibacterial wash. Programme

interruption (e.g. due to door opening) can

compromise elimination of germs.

X X 13.0 1.50 115 ±

Overnight 55°C

Normally soiled crockery, gentle and quiet (39

dbA) thanks to the lower pressure jet.

X X 13.0 1.20 290 ±

Summary of content (8 pages)

PAGE 1
Before using the dishwasher, read the installation and maintenance instructions carefully! GB GSI 5991 1. OVERVIEW Fault indication and wash time display In normal operation it indicates the remaining time (h:mm), whereas with “Delayed start” selected it indicates the time remaining until programme start (hh). If “F..” appears on the display, see chapter 5 “What to do if...”. Delayed Start button Press the button (repeatedly) to delay the start of the programme. Adjustable from 1 to 24 hours.
PAGE 2
. QUICK REFERENCE GUIDE Detailed instructions are given on the following pages; also see section “5. What to do, in case of...” 1. Switch on the appliance Press the ON/OFF button. 2. Select a programme Press the button “Select programme” or the programme selector to display the selected programme. If required, select possible options. 3. Select the type of detergent The detergent selection procedure varies depending on the dishwasher model. Chapter “1.
PAGE 3
. HOW TO USE THE APPLIANCE PROGRAMME SELECTION Press the button “Select programme” or the programme selector to display the selected programme. The appliance must be switched on. If required, select possible options. The corresponding indicator lights up. The correct programme and the selectable functions are given in table 1.1 on page 1. Programme times stated in the table were obtained under normal conditions and may vary depending on conditions.
PAGE 4
3. HOW TO USE THE APPLIANCE c. How to adjust the rinse aid dosage regulator The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button 2 to open the cover. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again. If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3).
PAGE 5
3. HOW TO USE THE APPLIANCE HOW TO LOAD THE RACKS UPPER RACK - depending on model Dish holder A In horizontal position for cups and long utensils. In raised position for plates and stemware. B Depending on the position, for small glasses or stemware. Glass holder Long-handled utensils (kitchen knives) must be arranged with the sharp end facing in towards the appliance. C It can be placed on the upper rack when the “Half load/Multizone” function is selected.
PAGE 6
4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. . 2. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. 3. Before using the dishwasher for the first time - The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
PAGE 7
5. WHAT TO DO IF... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes/solutions ...is not working/will not start - The appliance must be switched on. Check the household circuit fuse if there is no power supply. The dishwasher door must be closed.
PAGE 8
5. WHAT TO DO IF... Crockery and cutlery ... Possible causes/solutions ...are not perfectly clean/have food residues - ...have deposits: - regeneration salt residue - In the event of frequent use of low temperature programmes (50°C or lower) (if available), every now and again select a higher temperature programme The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”).