Instruction for Use

ManualsBrandsWhirlpool ManualsDishwashersGSIP 300 POWER PT

5019 496 01081

GSIP 300 POWER

Before using the dishwasher, read the

installation and maintenance instructions carefully!

1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to different loads, extra

functions, sensor settings (only with sensor programmes), water supply temperatures, water hardness and power supply voltage.

2) Energy label programme in compliance with EN 50242. - Information for Test Laboratories: for more detailed information on the conditions of the EN

comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been shown in collaboration with the Pasteur Institute, Lille (France), in conformity with Standard NF EN 13697 - November 2001.

1. OVERVIEW

Programme selector

START button

The indicator lights up during operation, flashes when a fault

occurs, and goes off at the end of the programme.

START button RESET function:

Press this button for at least 2 seconds to cancel a started

programme and selected extra functions. The main fault

indications (repeated flashing of the START indicator) can be

cancelled by RESETTING. Also refer to section 5 “What to do, in

case of...”.

Power Clean

High pressure with an additional jet for better washing results and

greater bottom rack load flexibility.

With this extra function selected the corresponding symbol

appears on the display.

Detergent setting at first startup and when using a different type of detergent

1. Select the third programme in the relevant table.

2. Press the START button for approx. 7 sec. to change the display.

3. Using the START button, set the required detergent:

The display shows: no symbol = powder detergent (standard supply)

(rinse aid and/or salt indicator active)

= 2 in 1

= 3 in 1 or other combined detergents

(In this way the rinse aid and/or salt indicator is deactivated)

4. Switch the appliance off and then on again. The type of detergent set is shown

on the display.

Fault indication and wash time display

In normal operation it indicates the remaining time (h:mm),

whereas with “Delayed start” selected it indicates the time

remaining until programme start (hh).

With indication “F..”, refer to section 5 “What to do, in case of …”.

Delayed start button

Press the button (repeatedly) to delay the start of the programme.

Adjustable from 1 to 24 hours. With each press of the button, the

delayed start indicator increases by one hour and after 24 restarts

from 00. Then press the START button. The dishwasher will start

after the set time.

Programme progress indicator

Rinse aid level indicator and salt level indicator

They light up when rinse aid or salt need to be added.

Add just before starting a wash cycle.

Half Load/Multizone button

Only load the upper rack or lower rack.

Press once = wash top rack (the indicator/symbol lights up)

Press twice = wash bottom rack (the indicator/symbol lights up)

Press 3 times = Off (Half load/Multizone deactivated).

When washing without the top rack, press the “Half load” (i.e.

“wash bottom rack”) button twice; the indicator /corresponding

symbol lights up.

On / Off button

Prewash Wash Dry

Table 1.1.

Table of programmes

Detergent

dispenser

Consumption

Programmes

Selectable

extra functions

Loading instructions large small Litres kWh Minutes

Steam Sensor + 40-70°C

Normally or very dirty dishes,

including pots and pans.

X X 7-17 0.99-1.75 65-220 ±

Pre-Rinse cold

Dishes to be washed later. — — 4.0 0.03 14 ±

Handwashing 40°C

Slightly dirty items, e.g. glasses

and cups, with a lower pressure

jet.

X — 10.0 0.85 125 ±

Quickwash 40°C

Slightly dirty dishes, without dry

residuals.

X — 10.0 0.65 30 ±

Bio Normal

50°C

Normally dirty dishes.

Energy-saving programme.

X X 11.0 0.98 170 ±

Hygienic +

Normally or very dirty dishes, with

additional antibacterial action. A

programme interruption (e.g. due to

door opening) can compromise

elimination of germs.

X X 13.0 1.50 115 ±

Overnight 55°C

Normally dirty dishes, gentle and

quiet (39 dbA) thanks to the lower

pressure jet.

X X 13.0 1.20 290 ±

Summary of content (8 pages)

PAGE 1
Before using the dishwasher, read the installation and maintenance instructions carefully! GB GSIP 300 POWER 1. OVERVIEW Fault indication and wash time display In normal operation it indicates the remaining time (h:mm), whereas with “Delayed start” selected it indicates the time remaining until programme start (hh). With indication “F..”, refer to section 5 “What to do, in case of …”. Delayed start button Press the button (repeatedly) to delay the start of the programme. Adjustable from 1 to 24 hours.
PAGE 2
. QUICK REFERENCE GUIDE Detailed instructions are given on the following pages; also see section “5. What to do, in case of...” 1. Switch on the appliance Press the ON/OFF button. 2. Select a programme Press the button “Select programme” or the programme selector to display the selected programme. If required, select possible options. 3. Select the type of detergent The detergent selection procedure varies depending on the dishwasher model. Chapter “1.
PAGE 3
. HOW TO USE THE APPLIANCE PROGRAMME SELECTION Press the button “Select programme” or the programme selector to display the selected programme. The appliance must be switched on. If required, select possible options. The corresponding indicator lights up. The correct programme and the selectable functions are given in table 1.1 on page 1. Programme times stated in the table were obtained under normal conditions and may vary depending on conditions.
PAGE 4
3. HOW TO USE THE APPLIANCE c. How to adjust the rinse aid dosage regulator The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button 2 to open the cover. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again. If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3).
PAGE 5
3. HOW TO USE THE APPLIANCE HOW TO LOAD THE RACKS CUTLERY RACK: May be used in two different positions. Position 1 Position 2 In position 2 the upper rack must be lowered (see “Upper rack height adjustment” C below). For optimum washing results, position cutlery as shown (handles of spoons facing inwards). Beware of sharp/pointed items. Risk of injury! Cutlery holder A A May be removed individually, depending on upper rack load.
PAGE 6
4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. . 2. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. 3. Before using the dishwasher for the first time - The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
PAGE 7
5. WHAT TO DO IF... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes/solutions ...is not working/will not start - The appliance must be switched on. Check the household circuit fuse if there is no power supply. The dishwasher door must be closed.
PAGE 8
5. WHAT TO DO IF... Crockery and cutlery ... Possible causes/solutions ...are not perfectly clean/have food residues - ...have deposits: - regeneration salt residue - In the event of frequent use of low temperature programmes (50°C or lower) (if available), every now and again select a higher temperature programme The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”).