TWOANDTHREE SPEED AUTOMATIC WASHERS Table of Contents ............. 2 Appliances 3950319 www.whirlpool.
TABLEOF CONTENTS WASHER SAFETY ............................................................... PARTS AND FEATURES USING YOUR WASHER 3 .................................................... 4 ...................................................... 5 UnderstandingWasher Cycles........................................ 5 Loading ............................................................................. 5 Normal Washer Sounds ................................................... 6 Starting Your Washer .......
WASHERSAFETY Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This symbol alerts you to hazards that can kill or hurt you and others. All willsymbol. be preceded by the safety alert symbol and the word "DANGER" or Thissafety is themessages safety alert "WARNING." These words mean: You will be killed or seriously injured if you don't follow instructions.
PARTSAND FEATURES This manual covers several different models. The washer you have purchased may have some or all of the parts and features listed below. ..... 6 1. Control panel Other features your washer may have: 2. Model and serial number label MAGIC CLEAN* lint filter 3. Liquid fabric softener dispenser XTRA ROLL ACTION PLUS _ agitator 4. Agitator ACCUWASH* temperature 5. Lid CLEAN TOUCH* control panel 6. Liquid bleach dispenser White porcelain basket control system 7. Basket 8.
USINGYOUR WASHER WASH RINSE 2. Rinse r_l When the Cycle Control knob is set to a number and pulled out, the washer fills (to the selected load size) before agitation and timing start. The washer begins agitating immediately after filling; agitation occurs with the washer lid up or down. selected 2. time Wash No agitation 3. Drain' During agitation, the agitator (on some models) creates a continuous rollover action that provides a thorough cleaning of the wash load. h_J No agitation 3.
Your new washer may make sounds your old one didn't. Because the sounds might be unfamiliar, you may be concerned about them. These sounds are normal. During washing When you select a small load size setting, your washer has a lower water level. This can cause a clicking sound from the upper part of the agitator. Electrical Shock Hazard During drain Plug into a grounded 3 prong outlet.
. (OPTIONAL STEP) Pour measured liquid chlorine bleach into the liquid chlorine bleach dispenser. Bleach will be diluted automatically during the wash part of the cycle. . Turn the LOAD SIZE selector to the correct setting for your wash load and the type of fabric being washed. • Choose a load size that allows the load to move freely for best fabric care. See "Loading." • You may change the load size selection after the washer has started filling by turning the selector to a different setting.
10, Push in the Cycle Control knob and turn it clockwise to the wash cycle you want. Reduce the wash time when using a small load size setting. See "Selecting a Cycle and Time." Normal cycle The Normal cycle features high-speed agitation for cleaning cottons and linens, and high spin times to shorten drying time. Select up to 1 5 minutes of wash time, depending on whether your load is lightly, moderately or heavily soiled. For lightly soiled cotton and linen fabrics, use the shortest time setting.
When using extra detergent for heavily soiled clothes, or washing speciahcare items, you may find an extra rinse and spin is needed. CARINGFORYOUR WASHER 1. Push in the Cycle Control knob and turn it clockwise to any of the Rinse settings 2, Pull out the Cycle Control knob. The washer fills to the selected load size, agitates, drains, and spins. NOTE: An EXTRA RINSE option is available (on some models). See "Starting your washer.
Your washer has a self-cleaning lint filter at the bottom of the basket. Wash and rinse water flow over the filter during agitation, separating the lint from the water. The lint spins out of the system during the spin part of the cycle. If your washer drains into a tub, remove any lint collected in the tub or strainer. Install and store your washer where it will not freeze. Because some water may stay in the hoses, freezing can damage your washer.
TROUBLESHOOTING First try the solutions suggested here and possibly avoid the cost of a service call... Washer won't fill, rinse or agitate Check the following: Is the power cord plugged in? Is the indicator on the Cycle Control knob properly lined up with a cycle? Turn the Cycle Control knob to the right slightly and pull to start.
Washer leaks Check the following: Are the fill hoses tight? Are the fill hose washers properly seated? Is the drain hose clamp properly installed? See the Installation Instructions. Is the sink or drain clogged? Sink and standpipe must be able to handle 17 gallons (64 L) of water per minute. Is water deflecting off the tub ring or the load? Center the tub before starting the washer. The wash load should be balanced and not overloaded. The fill or spray rinses can deflect off the load.
Load is wrinkled Did you unload the washer promptly? Unload the washer as soon as it stops. Garment damage • Did you use the right cycle for the load being washed? Use the Permanent Press cycle or another cycle with low spin speeds (if available) to reduce wrinkling. Did you overload the machine? The wash load must be balanced and not overloaded. Loads should move freely during washing.
For further assistance ASSISTANCE OR SERVICE If you need further assistance, you can write to Whirlpool with any questions or concerns at: Before calling for assistance or service, please check "Troubleshooting". It may save you the cost of a service call. If you still need help, follow the instructions below. When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request.
WHIRLPOOL* WASHERWARRANTY ONE-YEAR FULL WARRANTY For one year from the date of purchase, when this washer is operated and maintained according to instructions attached to or furnished with the product, Whirlpool will pay for FSP* replacement parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.
