Instruction for Use

ManualsBrandsWhirlpool ManualsDomestic AppliancesGSX 5520/1

Before using the dishwasher, read the

installation and maintenance instructions carefully!

5019 496 01103

GSX 5520

1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to

different loads, extra functions, sensor settings (only with sensor programmes), water supply temperatures, water hardness

and power supply voltage.

2) Energy label programme in compliance with EN 50242. - Information for Test Laboratories:

for more detailed information on the

EN comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on. Standard NF EN 13697 - November 2001.

1. OVERVIEW

On button

Off button

Delayed start button

Press the button repeatedly to delay the

start of the programme by 3, 6 or 9 hours.

Then press the START button. The

dishwasher will start at the set time.

Detergent setting upon initial use and when using a different type of detergent

1. Select the third programme in the relative table.

2. Press the START button for approx. 7 sec. to change the display.

3. Using the START button, select the desired detergent:

“3h” = 2in1, “6h” = 3in1, “9h” = other combined action detergents

(in this way, the rinse aid and/or salt indicator is deactivated). All 3

LEDs light up = Powder detergent (factory setting).

4. Switch the appliance off and then switch it on again. The selected

detergent type will be indicated on the display by the

corresponding LEDs for approx. 3 seconds.

Programme selection button

Press the button repeatedly until the desired programme

indicator lights up.

START

button

The indicator lights up during operation, flashes when a

fault occurs, and goes off at the end of the programme.

START

button reset function:

Press this button for at least 2 seconds; the selected

programme and options are cancelled. Main failure

displays (repeated flashing of the START indicator lamp)

can be cancelled by RESETTING. Detailed instructions

are given in chapter “What to do if...”.

An acoustic signal continues to sound as long as the error

persists.

Rinse aid level indicator and salt level indicator

These indicator lamps light up when rinse aid or salt

need to be added.

Add just before starting a wash cycle.

Table 1.1.

Table of programmes

Detergent

dispenser

Consumption

Programmes

Available

options

Description of programme large small Litres kWh Minutes

Pre-Rinse cold

Crockery to be washed later. — — 4.0 0.03 14 ±

Quickwash 40°C

Lightly soiled crockery, with no dried-

on food.

X — 10.0 0.65 30 ±

Bio

50°C

Normally soiled crockery.

Energy Saving Programme.

X X 12.0 1.05 165 ±

Hygienic +

Normally or heavily soiled crockery,

with additional antibacterial wash.

Programme interruption (e.g. due to

door opening) can compromise

elimination of germs.

X X 13.0 1.50 115 ±

Intensive 70°C

Recommended programme for heavily

soiled crockery, especially suitable for

pans and saucepans.

X X 14.0 1.55 155 ±

Summary of content (8 pages)

PAGE 1
Before using the dishwasher, read the installation and maintenance instructions carefully! GB GSX 5520 1. OVERVIEW Programme selection button Press the button repeatedly until the desired programme indicator lights up. On button START button The indicator lights up during operation, flashes when a fault occurs, and goes off at the end of the programme. START button reset function: Press this button for at least 2 seconds; the selected programme and options are cancelled.
PAGE 2
. QUICK REFERENCE GUIDE Detailed instructions are given in the following pages, see also chapter “5. What to do if...” 1. Switch on the appliance Open the dishwasher door. Press the ON button. 2. Select a programme Press the button or to bring up the desired programme on the display. Select options, if available. 3. Select the type of detergent The detergent selection procedure varies depending on the dishwasher model. Chapter “1. Overview” provides instructions for selecting detergent type. 4.
PAGE 3
. HOW TO USE THE APPLIANCE PROGRAMME SELECTION Press the button or to bring up the desired programme on the display. The appliance must be switched on. If required, select options (if supplied). The corresponding indicator lamp switches on. Appropriate programmes and relative available options are detailed in table 1.1 on page 1. Programme times stated in the table were obtained under normal conditions and may vary depending on conditions.
PAGE 4
3. HOW TO USE THE APPLIANCE c. How to adjust the rinse aid dosage regulator The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button 2 to open the cover. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again. If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3).
PAGE 5
3. HOW TO USE THE APPLIANCE HOW TO LOAD THE RACKS UPPER RACK - depending on model Crockery holder A Horizontal for cups and long-handled utensils. Vertical for plates and long-stemmed glasses. B Depending on the position, for small or long-stemmed glasses. Glass holder Long-handled utensils (kitchen knives) must be arranged with the sharp end facing in towards the appliance. Cutlery basket B A C C It can be placed on the upper rack when the “Half load/Multizone” function is selected.
PAGE 6
4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. . 2. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. 3. Before using the dishwasher for the first time - The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
PAGE 7
5. WHAT TO DO IF... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes/solutions ...is not working/will not start - The appliance must be switched on. Check the household circuit fuse if there is no power supply. The dishwasher door must be closed.
PAGE 8
5. WHAT TO DO IF... Crockery and cutlery ... Possible causes/solutions ...are not perfectly clean/have food residues - ...have deposits: - regeneration salt residue - In the event of frequent use of low temperature programmes (50°C or lower) (if available), every now and again select a higher temperature programme The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”).