Health & Safety, Use & Care and Installation guide www.whirlpool.
ENGLISH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EN ENGLISH HEALTH & SAFETY, USE & CARE and INSTALLATION GUIDES THANK YOU FOR BUYING A WHIRLPOOL PRODUCT. In order to receive a more complete assistance, please register your appliance on www.whirlpool.eu/register Index Health and Safety guide SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6th SENSE LIVE REMOTE CONTROL / DAILY USE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 6th SENSE LIVE FEATURE / FAQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 ENERGY SAVING . . . . . . . . . . . . .
EN Health and Safety guide SAFETY INSTRUCTIONS IMPORTANT TO BE READ AND OBSERVED Before using the dryer carefully read, Health and Safety and Use and Care guides. Keep these instructions close at hand for future reference. YOUR SAFETY AND SAFETY OF OTHERS IS VERY IMPORTANT. This manual and the dryer itself provide important safety warnings, to be read and observed at all times. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
out so that the heat is dissipated. The last phase of the drying cycle is done without heat (cool down phase), to assure that the laundry stays at a temperature level which is not leading to a damaging of the laundry. If you want to stack the dryer on a washing machine, first contact our After-Sales Service to verify if this is possible. Stacking of a dryer is only admitted if the dryer is safely fixed on the washing machine by using an appropriate stacking kit.
EN If, due to lack of space, the dryer must be installed directly next to a gas or coal stove, a heat insulating plate (85 x 57 cm) must be installed in between and the side of the plate facing the stove must be covered with aluminium foil. The dryer is not designed for built-in installation. The dryer can be installed under a worktop, provided that adequate ventilation of the dryer is assured.
Do not overdry the laundry. Take care that no lint or dust is accumulated around the dryer. Fabric softeners, or similar products, should be used as specified by the fabric softener instructions. CLEANING AND MAINTENANCE The dryer must be disconnected from the power supply before carrying out any cleaning or maintenance operation. Never use steam cleaning equipment. SAFEGUARDING THE ENVIRONMENT For dryer models with heatpump technology: This dryer contains fluorinated greenhouse gas (R134a).
EN ENERGY SAVING TIPS Always dry a full load, depending on the type of laundry and the programme/ drying time. For more detailed information, see the programme chart. By preference use the maximum spin speed allowed by your washing machine, since draining the water mechanically requires less energy. You will save time and energy when running your drying cycle. Always select the correct programme/drying time for the load in order to obtain the desired drying results.
The following statements refer to the portions of this software based in part on FreeRTOS v7.0.2, http://www.freertos.org. The use of this software is governed by the terms of GNU General Public License v. 2, which is available at: http://www.gnu.org/ licenses/gpl-2.0.html. A copy of the source code may be obtained by written request for the software by name to opensource@ whirlpool.com, along with the address for delivery.
EN Use and Care guide PRODUCT DESCRIPTION APPLIANCE 1. 1. Worktop 2. Control panel 3. Water tank 4. Door 5. Door handle 6. Door filter (behind door) 7. Plinth 8. Adjustable feet (4) 2. 3. 5. 4. 6. 7. 8. CONTROL PANEL 18. 17. 16. 15. 14. 11. 12. 13. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 1. On/Off button (Reset if long pressed) 2. Settings button 3. Drum light 4. Steam option 5. Remote control button 6. Finish in 7. Drying time 8. Dryness level 9.
DOOR To open the door, pull the handle. To close the door, hold the handle and push so that you can hear it click shut. If you interrupt a running programme by opening the door, the programme will be reset if the dryer door is not closed again within one minute. DRUM LIGHT (if available) • During programme selection: the light goes on for laundry loading. • After programme start: the light fades on and off while the laundry load is detected.
EN HOW TO USE THE APPLIANCE 6th SENSE LIVE FEATURE Thanks to the 6th Sense Live feature, your appliance can be connected to the Internet. Using the 6th Sense Live app on your smartphone / tablet, you can: • monitor the status of the appliance • get informed on the programme status • set and start a programme • change, modify, or reset a running programme • access additional contents.
FIRST TIME USE 1. WHEN SWITCHING ON THE DRYER FOR THE 2. CHECK WATER TANK FIRST TIME, YOU WILL BE ASKED TO Make sure that the water tank is correctly inserted Set the desired language Press the UP or DOWN key to select the desired language, and confirm by pressing the OK key. Adapt the value for your local water conductivity The drying results are affected by the conductivity of the water used during washing.
EN DAILY USE WARNING Make sure that no lighters or matches remain in the laundry. 1. LOAD THE LAUNDRY Respect the care labels of your laundry; make sure that it is appropriate for being treated in a dryer. Drying Care Labels The dots indicate the temperature degree for drying the laundry. Normal temperature Reduced temperature Do not tumble dry Open the door and load the laundry. Observe the maximum load sizes given in the section Programmes. 2.
selectable for your programme are indicated on the display. Press the UP or DOWN key to navigate through the list of available options. The selected option blinks. To confirm selection, press the Ok key. The corresponding symbol over the display lights up. Some options / functions can be selected by directly pressing the button. programme on pause • change your settings • press Start/Pause again to continue the programme. 7.
EN PROGRAMMES Meaning of the care labels: The dots indicate the temperature degree for drying the laundry. Normal temperature Reduced temperature Do not tumble dry PROGRAMME Type of Drying and Recommendations ECO COTTON Standard cotton programme, suitable to dry normal wet cotton laundry. Most efficient programme in terms of energy consumption for drying cotton laundry. The values on the Energy Label are based on this programme. max. load (kg): For drying cotton laundry. max.
PROGRAMME Type of Drying and Recommendations DELICATES For drying delicate laundry which needs gentle treatment. Care Labels Regulations max. load (kg): 2.5 default programme duration (h): 1:15 selectable options: Fresh care WOOL EXCELLENCE JEANS For drying woollens labelled with the Woolmark TOTAL EASY CARE WOOL. For drying cotton jeans-wear and garments made of robust jeans like material, such as trousers and jackets. max. load (kg): 1.
EN PROGRAMME Type of Drying and Recommendations DRYING TIME Time-restricted drying programme. Select programme duration by option Drying time. For all fabrics appropriate for tumble drying. Suitable to add an additional short drying phase after programme end. Refer to OPTIONS, FUNCTIONS AND INDICATORS / option Drying time for more information. max. load (kg): Gentle drying of shirts and blouses made of cotton, synthetic fibres or their blends. max.
PROGRAMME Type of Drying and Recommendations MINI LOAD Economic drying of small laundry loads. Care Labels Regulations max. load (kg): 1.0 default programme duration (h): 1:00 selectable options: Fresh care max = maximum capacity of the dryer Programme durations indicated in the table are default values. The programme duration mainly depends on the humidity level of the laundry and the volume of the laundry load. For that reason, the real programme duration can deviate from the indicated values.
EN OPTIONS OPTIONS WHICH ARE DIRECTLY SELECTABLE BY PRESSING THE RESPECTIVE BUTTON STEAM OPTION Minimizes creasing of garments made of cotton, synthetics and their blends by adding a humidifying phase at the end of the drying cycle. Use the option with small loads only, unload the garments from the dryer DRYING TIME OPTION To adjust the desired drying time if Drying time or Airing programme has been selected.
FUNCTIONS ON/OFF To switch the dryer on: press the button until the Start/Pause button lights up. To switch the dryer off after programme end: press the button until the lights go off. WARNING To cancel a running programme: press and hold the button until the display indicates that the programme is cancelled. After cancelling a running out so that the heat is programme, quickly remove dissipated. all items and spread them UP AND DOWN KEYS To navigate through and select from a display menu.
EN Press the UP or DOWN key to set the desired delay of the programme end. Press Start / Pause - the countdown of the delay starts. The display indicates the default programme duration of the selected programme, and underneath the set “Finish in” period. The Start/Pause button and the Finish in button light up; the colon between hours and minutes of the Finish in period blinks. The programme starts automatically, in time to be finished at the end of the delay period.
INDICATORS ENERGY MONITOR The less levels of the energy monitor are lit, the more economic is your programme setting. FAILURE For any failure indication on the display, refer to section TROUBLESHOOTING for more information. CONNECTION STATUS If your dryer has been already connected to the Internet (see 6th Sense Live Feature/ Setup Procedure section in the Use and Care Guide) and the radio is on, this indicator provides a feedback about the status of the Internet connection through your WiFi router.
EN 6th SENSE LIVE FEATURE / SETUP PROCEDURE To enable the appliance to be remotely monitored and controlled, you first have to complete successfully the setup procedure. The setup procedure has to be carried out only once. You have to carry it out again only if you change your router setup properties (network name and password). TECHNICAL REQUIREMENTS • A wireless router 2.4Ghz WiFi b/g/n connected to the Internet. • For Android users: a smart phone running Android 4.
AUTOMATIC SETUP PROCEDURE This procedure is applicable only if your router supports WPS 2.0 (or greater) 1. Turn on your router and activate the WPS (WiFi Protected Setup) feature. The WPS indicator light turns on and the feature remains active for about 2 minutes. 2. While the WPS in on, press the Remote Control button. It will operate as a shortcut to the Live menu. Otherwise select the Live menu from the Setting menu using the UP and DOWN key and press the OK key. 3.
EN MANUAL SET UP PROCEDURE This procedure uses the Micro Access Point technology and is applicable if your router does not support WPS 2.0. 1. Before starting the setup procedure take note of your home wireless network name (SSID), its PASSWORD and the SAID code of the dryer. 2. Turn on your router and make sure the Internet connection is working. 3. Press the Remote Control button. It will operate as a shortcut to the Live menu.
RESET PROCEDURE The reset procedure has to be carried out if you change the router setup properties (network name and password) or if the dryer is not able to connect to the cloud. 1. 4. Select the Live menu from the Setting menu using the UP and DOWN key and press the OK key. When the provisioning process is complete a message appears on the display. 2. Select the reset feature from the Live If you want to use the Live feature again you have to repeat the setup procedure.
6th SENSE LIVE REMOTE CONTROL / DAILY USE The Remote Control mode allows to control the dryer remotely using a smartphone or a tablet. The Remote Control function needs some specific 1. Make sure the router is on and connected to the Internet. 2. Switch on the dryer. 3. Load your laundry, close the door. 4. Make sure the Connection Status indicator is solidly lit. EN technical devices and some preparatory setup. Find detailed information in the "6th Sense Live Feature / Setup procedure" section. 6.
6th SENSE LIVE FEATURE / FAQ QUESTION ANSWER Are there any differences between using a smart phone (or a tablet) with Android or iOS? Which WiFi protocols are supported by the appliance? You can use the operating system you prefer, there are no differences. Which version of WPS is supported? The appliance supports WPS 2.0 or higher. To verify the WPS used by your router check the router documentation. The radio installed in the dryer supports WiFi b/g/n for European countries.
EN QUESTION ANSWER I changed the router, what do I have to do? You can either maintain the same setup properties (network name and password) or erase the previous setup from the appliance (reset process) and carry out the setup process again (see "Live-Remote Control/Setup procedure"). You have to erase the previous setup from the appliance (reset process) and carry out the setup process again (see "Live-Remote Control/Setup procedure"). When the power returns, the Remote Control will be deactivated.
ENERGY SAVING AUTOMATIC SWITCH-OFF FUNCTION The dryer is designed to save energy. After the programme has finished, it therefore switches off automatically after about a quarter of an hour. ENERGY SAVING TIPS • To reduce the drying time, make sure that the laundry is spun with the maximum possible spin speed of the drying programme. This reduces the moisture content in the laundry. • Preferably dry a full load, as indicated in the Programmes table. This optimizes the relative energy consumption.
EN CLEANING & MAINTENANCE WARNING Do not use flammable fluids to clean the dryer. For any cleaning and maintenance, switch off the dryer. EMPTYING THE WATER TANK Empty the water tank after each programme, provided the drain hose is not connected to your sewage system (refer to INSTALLATION GUIDE). 1. Hold the handle and carefully pull out the water tank. Hold the full water tank with both hands. 3. Insert the water tank by pushing it back into place.
CLEANING THE DOOR FILTER Clean the door filter after each programme. Make sure that the laundry is unloaded. Open the door. 4. Clean the filter compartment with a soft cloth, or carefully with a vacuum cleaner. 1. Remove the door filter by pulling it upwards. 2. Press the button to open the door filter. 3. Carefully remove the complete lint from the screen by hand. If needed, the screen can be cleaned also under running water, using a soft brush. 34 5.
EN CLEANING THE BOTTOM FILTER Clean the bottom filter after every fifth programme. 1. Open the bottom flap. 4. Clean the filter foam and the filter by hand or under running water. Do not wash the filter foam in the washing machine. 2. Hold the handle and pull out the bottom filter. 5. Carefully wring out the filter foam. Do not insert it in the bottom filter dripping wet. 3. Remove the foam from the bottom filter, to clean it. 6. Fix the filter foam on the bottom filter. 7.
8. Insert the bottom filter again. Make sure that it 10. Close the bottom flap. is completely integrated in the filter compartment. 9. Clap the filter handle downwards.
CLEANING THE OUTSIDE OF THE DRYER EN Use a soft damp cloth to clean the outer parts of the dryer. Do not use glass or general purpose cleaners, scouring powder or similar to clean the control panel – these substances might damage the surfaces.
REVERSING THE DOOR STOP If needed, the door stop of the dryer door can be reversed. Use pliers and a cross-head screwdriver for the procedure. For removing and fixing the door, the help of a second person is recommended. Make sure that the dryer is unplugged. Open the dryer door. 1. 3. Remove the two screws on the door hinge. Remove the two screws which are situated over and under the door lock, left from the door opening. 4. Remove the door and carefully lay it upside 2.
EN 5. Unscrew the bottom screw, to release the cover frame on the front of the door. 7. Carefully turn the door frame in clockwise direction, and remove it. 2 1 8. Turn the door again and lay it upside down. 6. Turn the door and lay it down on the door glass.
9. Remove the two side screws. Do this on both 11. Remove the side parts on each side of the sides of the door. door. 1 2 12. Reverse the side parts and insert them again. 10. Remove the 4 inner screws on each side of the door.
EN 13. Fix the 2 side screws on both sides of the door again. 15. Turn the door and lay it down on the door glass. 1 2 14. Fix the 4 inner screws on each side again. 16. Refit the door frame.
17. Turn the door again and lay it upside down. 19. Fix the two screws over and under the door Fix the bottom screw again. 18. Insert the door lock on the right side of the door opening. Press it completely inside the hole and move it a bit downwards, until the small knob of the door lock latches. 42 lock, on the right side of the door opening. 20. Fix the door on the left side of the door opening by turning in the two screws.
EN TROUBLESHOOTING GUIDE & AFTER-SALES SERVICE Your dryer is equipped with various automatic safety functions. These enable failures to be detected in good time and the safety system can react appropriately. These failures are frequently so minor that they can be removed within a few minutes.
Problem Possible Cause Solution WATER DROPLETS ARE BENEATH THE DRYER Bottom filter not inserted correctly • Check position of the bottom filter and make sure it is completely integrated in the filter compartment. Lint remaining on bottom filter or door seal • Remove lint residues on the rubber seals of bottom filter and door seal. Water tank not inserted correctly • Push in the water tank and make sure that it is completely integrated in the tank compartment.
FAILURE INDICATOR AND MESSAGES EN Make sure to • Empty the water tank after each programme • Clean the door filter after each programme • Clean the bottom filter after every fifth programme Failure Indicator Display message WATER TANK FULL CLEAN BOTTOM FILTER Possible Cause Water tank may be • filled with water • Empty water tank; make sure to insert it properly afterwards. • not correctly positioned • Push in the water tank to make sure that it is correctly inserted in the tank compartment.
Below is a summary of possible failure causes and solutions. If the problem persists after having followed the instructions as indicated below, press and hold On/ Off for at least three seconds. If afterwards the failure indication still appears, switch off and unplug the dryer and contact our After-Sales Service. Failure Indicator 46 Display message Possible Cause Solution F01 to F04 Failure of a component Press and hold On/Off for at least 3 seconds.
EN TRANSPORT AND HANDLING WARNING Never lift the dryer by holding it at the worktop. 1. Unplug the dryer. 2. Make sure that door and water tank are 3. If the drain hose is connected to your sewage system, fix the drain hose on the rear of the dryer again (see Installation Guide). properly closed.
AFTER-SALES SERVICE BEFORE CALLING THE AFTER-SALES SERVICE 1. See if you can solve the problem by yourself with the help of the suggestions given in the TROUBLESHOOTING GUIDE. 2. Switch the appliance off and on again to see if the failure persists. IF AFTER THE ABOVE CHECKS THE FAILURE STILL OCCURS, GET IN TOUCH WITH THE NEAREST AFTER-SALES SERVICE To receive assistance, call the number shown on the warranty booklet or follow the instructions on the website www.whirlpool.
EN 1. 2a. 2b.
3a. max 2 cm max 0.79 inch 3b.
EN 4.
5. 6a. 6b. ..............
EN 53
EN 55
EN 400010838912 Whirlpool is a registered trademark of Whirlpool, USA 001 n