Instruction manual TUMBLE DRYER Contents EN Important information, 2-3 FR EN English,1 Français,17 ES Español,33 PT Português,49 Installation, 4 Where to install the tumble dryer Ventilation Electrical connections Preliminary information Description of the tumble dryer, 5-6 Features Control panel How to carry out a drying cycle, 7 Starting and selecting a programme Programmes and options, 8-9-10 IDCA G35 Programme chart Special programmes Options Opening the door Laundry, 11-12 Sorting laundry
Important information EN To ensure that the condenser dryer functions efficiently, the following routine maintenance procedures must be carried out: Fluff filter – CLEAN off any fluff build-up on the filter after each drying cycle. Failure to clean the filter after each drying cycle can undermine drying performance as the machine takes longer to dry and thus consumes more energy. Water container – empty the water container after each drying cycle.
Condenser unit - remove any fluff build-up from the condenser on a monthly basis. EN Step 1 Open the condenser cover - grip the handle and pull towards you. Step 2 Remove the condenser by turning the 3 catches, then pull the condenser towards you. (It is normal for some residual water to be left in the tubes). Step 3 Clean the condenser with running water over the rear side to remove any fluff deposits.
Installation Electrical connections • Install the dryer far from gas ranges, stoves, radiators or hobs, as flames may damage it. If the dryer is installed below a worktop, ensure there are 10 mm between the upper panel of the dryer and any objects above it, and 15 mm between the sides of the machine and the walls or furniture units adjacent to it. This ensures adequate air circulation. Before plugging the appliance into the socket, check the following: • Make sure your hands are dry.
Description of the tumble dryer Features Opening the door EN Rating plate Water container Press the door Model & Serial Numbers Filter Air intake grille Condenser unit (cover open) Condenser cover handle (pull to open) Control panel On/Off button Programme selection knob Options buttons and indicator lights Start/Pause button and indicator light Maintenance indicator lights Drying phase or Delay timer indicator lights 5
EN ON/OFF/Reset button Pressing the button normally will cause the machine to switch on or off. If the button is pressed for 3 seconds while the dryer is in function, the machine will switch off and the running cycle will reset. Programme selection knob Allows for setting the programme: turn until the indicator points towards the desired programme (see Starting and selecting a programme). Options buttons Allow for selecting the options available for the selected programme.
How to carry out a drying cycle Starting and selecting a programme EN 1. Plug the dryer into the power supply socket. 2. Select the programme according to the type of laundry (see Laundry). 3. Open the door, ensure that the filter is clean and securely placed and that the water container is empty and correctly slotted (see Care and maintenance). 4. Load the machine, making sure that no piece of laundry gets between the door and the relative seal. Close the door. 5.
Programmes and options EN Programme chart Programme Max. load (kg) Compatible options Cycle duration Energy Saver 1 Eco Cotton 1 Pre Care – Post Care – Delay timer 30’ 2 Eco Shirts 1 Pre Care – Post Care – Delay timer 30’ 3 Eco Synthetics 1 Pre Care – Post Care – Delay timer 30’ 4 Ready to Wear Max. Pre Care – Post Care – Delay timer 160’ 5 Cupboard dry Max. Pre Care – Post Care – Delay timer 145’ 6 Iron dry Max.
Wool Programme This programme is specific for items that withstand tumble drying and are labelled with the symbol. It is suitable for loads of up to 1 kg (about 3 jerseys). We recommend turning the garments inside out before drying them. This programme lasts about 60 minutes, although it may last longer depending on the size and density of the load and on the spin speed used during the wash cycle.
EN Options The options allow for customising the selected programme according to one’s own needs. Delay timer The start of some programmes (see Programmes and options) may be delayed up to 9 hours. Press the button repeatedly to enter the desired delay time. Before setting a delayed start, make sure that the water container is empty and that the filter is clean.
Laundry Sorting laundry Care labels • Check the symbols on the care labels of the various garments to verify whether the garments can be safely tumble dried. • Sort laundry according to the type of fabric. • Empty all pockets and check for loose buttons. • Close zips and hooks and fasten belts and strings without tightening them. • Wring out garments to remove the maximum amount of water possible. Always check the care labels, especially when placing garments in the tumble dryer for the first time.
EN Special items • Amount of laundry: single items and small loads may take longer to dry. Blankets and bedcovers: acrylic items (Acilian, Courtelle, Orion, Dralon) must be dried with great care at low heat. Avoid drying for long periods. • Drying: if items are to be ironed, they can be removed from the dryer while still slightly damp. Items that require complete drying can be left longer. Creased or pleated garments: read the drying instructions supplied by the manufacturer. • Heat setting.
Warnings and suggestions ! This appliance was designed and manufactured in com- pliance with current international safety standards. The following information is provided for safety reasons and must be read carefully. General safety • The final part of a tumble dryer cycle occurs without heat (cooling cycle) to ensure that the laundry is not damaged due to excessive temperatures.
Care and maintenance EN Disconnecting the power supply ! Disconnect the dryer when not in use or during cleaning and maintenance operations. Cleaning the filter after each cycle The filter is a fundamental component of the dryer: its function is to collect lint and fluff that form during drying. Clean the filter once drying is completed, by rinsing it under running water or cleaning it with a vacuum cleaner.
Troubleshooting If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the Technical Assistance Centre (see Assistance). Problem: Possible causes / Solutions: The dryer does not start. • • • • • • • The drying cycle does not start. • A delayed start time has been set (see Programmes and options). • The START/PAUSE button has been pressed; a short delay follows before the dryer starts running.
Assistance EN Before contacting the Technical Assistance Centre: Spare parts • Follow the troubleshooting guide to check whether problems can be solved personally (see Troubleshooting). • If not, switch the dryer off and contact the Technical Assistance Centre closest to you. This dryer is a complex machine. Attempting to repair it personally or with the aid of an unqualified personnel may put the safety of people at risk, damage the machine or invalidate the spare parts guarantee.
Mode d’emploi SÈCHE-LINGE Table des matières FR Français FR Informations importantes, 18-19 Installation, 20 Où installer le sèche-linge Ventilation Raccordement électrique Informations préliminaires Description du sèche-linge, 21-22 Caractéristiques Tableau de bord Comment effectuer un cycle de séchage, 23 Démarrage et choix du programme Programmes et options, 24-25-26 IDCA G35 Tableau des programmes Programmes spéciaux Options Ouverture de la porte Linge, 27-28 Tri du linge Étiquettes d’entretie
Informations importantes FR Pour assurer le bon fonctionnement du sèche-linge à condensation il faut suivre le schéma d’entretien ordinaire indiqué ci-dessous : Filtre à peluches – IL EST NÉCESSAIRE d’éliminer les peluches qui s’accumulent sur le filtre après chaque cycle de séchage. Étape 1 Ouvrez la porte du sèche-linge en appuyant comme illustré par la figure.
Groupe condenseur - Il est nécessaire d’éliminer les peluches accumulées sur le condenseur tous les mois. FR Étape 1 Ouvrez le couvercle du condenseur - tirez la poignée vers vous. Étape 2 Enlevez le condenseur en tournant les 3 clips, ensuite tirez le condenseur vers vous. (Dans les tuyaux il pourrait y avoir encore de l’eau : cela est normal). Étape 3 Nettoyez le condenseur sous l’eau courante par la partie arrière, de manière à éliminer tout dépôt de peluches.
Installation Raccordement électrique • Placez votre sèche-linge à une certaine distance des cuisinières, fourneaux, radiateurs, ou plaques de cuisson à gaz, car les flammes peuvent endommager cet appareil. Si vous installez cet appareil 15 mm sous un plan de travail, faites 15 mm en sorte de laisser un espace de 10 mm entre le dessus de l’appareil et tout autre objet sur ou au-dessus de celui-ci, et un espace de 15 mm entre ses côtés et les éléments d’ameublement ou les murs latéraux.
Description du sèche-linge Caractéristiques Ouverture de la porte Plaque signalétique de l’appareil Réservoir d’eau Appuyez sur la porte FR Numéro de série et référence du modèle Filtre Grille d’entrée d’air Groupe condenseur (couvercle ouvert) Poignée du couvercle du condenseur (tirez pour ouvrir) Tableau de bord Touche On/Off Bouton Programmes Touches et voyants Options Touche avec voyant Marche/Pause Voyants d’entretien Voyants des phases de séchage ou de départ différé 21
FR Touche ON/OFF/Reset Une pression normale sur cette touche fait allumer ou éteindre l’appareil. Si le sèche-linge est en marche, une pression prolongée d’au moins 3 secondes fait éteindre l’appareil et remettre à zéro le cycle en cours. Bouton Programmes Permet de sélectionner les programmes : tournez le bouton jusqu’à positionner l’indicateur sur le programme souhaité (voir Démarrage et choix du programme). Touches options Permettent de choisir les options disponibles pour le programme sélectionné.
Comment effectuer un cycle de séchage Démarrage et choix du programme FR 1. Branchez la fiche du sèche-linge dans la prise de courant électrique. 2. Sélectionnez le programme en fonction du type de linge (voir Linge). 3. Ouvrez la porte et assurez-vous que le filtre est propre et en place et que le réservoir d’eau est vide et en place (voir Entretien). 4. Chargez la machine en faisant attention à ce qu’aucun vêtement ne s’interpose entre la porte et le joint de la porte. Fermez la porte. 5.
Programmes et options FR Tableau des programmes Programme Charge maxi (Kg) Options compatibles Durée cycle Energy Saver 1 Eco Coton 1 Alarme – Anti-froissement début – Anti-froissement fin - Départ différé. 30’ 2 Eco Chemises 1 Alarme – Anti-froissement début – Anti-froissement fin - Départ différé. 30’ 3 Eco Synthétiques 1 Alarme – Anti-froissement début – Anti-froissement fin - Départ différé. 30’ Coton 4 Coton intensif Max.
Programme Laine C’est un programme réservé aux articles supportant le séchage au tambour et portant le symbole . Vous pouvez l’utiliser pour des charges jusqu’à 1 kg (3 pull-overs environ). Il est conseillé de tourner les vêtements à l’envers avant de les charger dans le sèche-linge. Ce programme prend 1:00 (hrs:mins) environ, mais parfois cette durée se prolonge, selon les dimensions de la charge, sa densité et la vitesse d’essorage du lave-linge.
FR Options Les options permettent de personnaliser le programme sélectionné en fonction de vos exigences. Départ différé Le départ de certains programmes (voir Programmes et options) peut être retardé d’un délai pouvant aller jusqu’à 9 heures. Appuyez plusieurs fois de suite sur la touche jusqu’à ce que le retard désiré soit affiché. Avant de régler un départ différé, assurez-vous que le réservoir d’eau et vide et que le filtre est propre.
Linge Tri du linge Étiquettes d’entretien • Vérifiez les symboles sur les étiquettes des vêtements pour vous assurer que les articles peuvent être passés au sèche-linge. • Triez votre linge par type de textile. • Videz les poches et contrôlez les boutons. • Fermez les fermetures éclair et les crochets et attachez les ceintures et les cordons, sans serrer. • Essorez chaque article de manière à éliminer autant d’eau que possible.
FR Linge ou vêtements particuliers • La quantité de linge : les articles uniques ou les petites charges peuvent prendre plus longtemps à sécher. Couvertures et dessus de lits : les articles en acrylique (Acilan, Courtelle, Orion, Dralon) doivent être séchés avec des précautions particulières, à basse température. Évitez de les sécher pendant une durée prolongée.
Précautions et conseils ! Cet électroménager a été conçu et réalisé conformément aux normes internationales de sécurité. Ces consignes sont fournies pour des raisons de sécurité, il faut les respecter scrupuleusement. Sécurité générale • La partie finale d’un cycle du sèche-linge se produit sans chaleur (cycle de refroidissement) afin de s’assurer que le linge demeure à une température qui ne risque pas de l’abîmer.
Soin et entretien FR Interruption de l’alimentation électrique ! Débranchez votre sèche-linge lorsque vous ne l’utilisez pas, lorsque vous le nettoyez et durant toutes les opérations d’entretien. Nettoyage du filtre après chaque cycle Le filtre est une pièce importante de votre sèche-linge : il accumule des peluches qui se forment durant le séchage. Par conséquent, une fois le séchage terminé, nettoyez le filtre en le rinçant sous l’eau courante ou avec votre aspirateur.
Problèmes et solutions Si vous trouvez que le sèche-linge ne fonctionne pas correctement, avant de contacter le Service après-vente (voir Assistance), consultez attentivement le tableau suivant afin de pouvoir résoudre les problèmes éventuels : Problème : Le sèche-linge ne démarre pas. Le cycle de séchage ne démarre pas. L’appareil met longtemps à sécher. Le voyant « Vider l’eau » clignote, mais le sèche-linge n’a fonctionné que pendant une courte période.
Assistance FR Avant d’appeler le Centre de Service après-vente : Pièces détachées • Suivez le guide d’aide à la résolution des problèmes pour voir si vous n’arrivez pas à résoudre le problème vous-même (voir Problèmes et solutions). • Dans le cas contraire, éteignez votre sèche-linge et contactez le Centre de Service après-vente le plus proche. Ce sèche-linge est un appareil complexe.
Manual de instrucciones SECADORA Índice ES Español ES Información importante, 34-35 Instalación, 36 Dónde instalar la secadora Aireación Conexión eléctrica Información preliminar Descripción de la secadora, 37-38 Características Panel de control Cómo realizar un secado, 39 Puesta en funcionamiento y selección del programa Programas y opciones, 40-41-42 IDCA G35 Tabla de programas Programas especiales Opciones Abertura de la puerta Ropa, 43-44 Subdivisión de la ropa Etiquetas de mantenimiento Prend
Información importante ES Para el funcionamiento eficiente de la secadora por condensación es necesario respetar el esquema de mantenimiento ordinario indicado a continuación: Filtro para la pelusa – ES NECESARIO quitar la pelusa que se deposita en el filtro al finalizar cada ciclo de secado. Fase 1 Abra la puerta de la secadora presionándola como se indica en la figura.
Unidad de condensación - Es necesario limpiar la pelusa del condensador cada mes. ES Fase 1 Abra la tapa del condensador - sostenga la manija y tire hacia Ud. Fase 2 Quite el condensador girando los 3 ganchos y luego tire del condensador hacia Ud. (Podría haber agua en los tubos: esto es normal). Fase 3 Limpie el condensador con agua haciéndola pasar por la parte posterior para extraer posibles depósitos de pelusa.
Instalación Dónde instalar la secadora • Las llamas pueden averiar la secadora, por lo tanto, debe estar alejada de cocinas a gas, estufas, radiadores o encimeras. Si el electrodoméstico debe instalarse debajo de una 15 mm encimera, es necesario dejar 15 mm un espacio de 10 mm entre el panel superior del electrodoméstico y los otros objetos dispuestos encima de la misma, y un espacio de 15 mm entre los lados del electrodoméstico y las paredes o las decoraciones dispuestas al costado del mismo.
Descripción de la secadora Características Abertura de la puerta ES Presione sobre la puerta Placa de datos de funcionamiento Contenedor de recolección de agua Número de serie y número de modelo Filtro Rejilla de la toma de aire Unidad de condensación (tapa abierta) Manija de la tapa del condensador (tire para abrir) Panel de control Botón On/Off Mando de Programas Botones y pilotos de Opciones Botón y piloto START/PAUSE Pilotos de mantenimiento Pilotos de fases de secado o comienzo retra
ES Botón ON/OFF/Reset Presionar en forma normal el botón para encender y apagar el aparato. Si la secadora está en funcionamiento, una presión prolongada durante 3 segundos apaga el aparato y reactivar el ciclo en curso. Mando de Programas Permite seleccionar el programa : gire hasta que el indicador esté orientado hacia el programa deseado (ver Puesta en marcha y Selección del programa). Botones de opciones Permiten elegir las opciones disponibles para el programa seleccionado.
Cómo realizar un secado Puesta en marcha y selección del programa ES 1. Introduzca el enchufe de la secadora en la toma de alimentación eléctrica. 2. Seleccione el programa en función del tipo de ropa (ver Ropa). 3. Abra la puerta y controle que el filtro esté limpio y en posición y que el contenedor de recolección de agua esté vacío y colocado correctamente (ver Mantenimiento). 4. Cargue la máquina teniendo cuidado que ninguna prenda se interponga entre la puerta y la junta. Cierre la puerta. 5.
Programas y opciones Tabla de programas ES Programa Carga máx. (kg) Opciones compatibles Duración del ciclo Energy Saver 1 Eco Algodón 1 Pre antiarrugas – Post antiarrugas - Comienzo retrasado. 30’ 2 Eco Camisas 1 Pre antiarrugas – Post antiarrugas - Comienzo retrasado. 30’ 3 Eco Sintéticos 1 Pre antiarrugas – Post antiarrugas - Comienzo retrasado. 30’ 4 Algodón Extra Max. Pre antiarrugas – Post antiarrugas - Comienzo retrasado. 160’ 5 Algodón Ropero Max.
Programa Lana Este es un programa dedicado a las prendas que soportan el secado en tambor marcadas con el símbolo . Puede utilizarse para cargas de hasta 1 kg (aproximadamente 3 jerseys). Se aconseja dar vuelta las prendas antes del secado. Este programa requiere aprox. 1:00 (hrs:mins), pero puede durar más tiempo dependiendo del tamaño y la densidad de la carga y de la velocidad del centrifugado empleada en la lavadora.
Opciones ES Las opciones permiten personalizar el programa seleccionado en base a las exigencias personales. Comienzo retrasado El comienzo de algunos programas (ver Programas y opciones) puede retrasarse hasta 9 horas. Presione varias veces el botón hasta alcanzar el retraso deseado. Antes de programar un comienzo retrasado asegurarse que el contenedor de recolección de agua esté vacío y que el filtro esté limpio.
Ropa Subdivisión de la ropa Etiquetas de mantenimiento • Controle los símbolos de la etiqueta de las diferentes prendas para comprobar si las prendas pueden someterse a un secado en tambor. • Divida la ropa a lavar en función del tipo de tejido. • Vacíe los bolsillos y controle los botones. • Cierre las cremalleras y los ganchos y ate los cintos y lazos sin ajustar. • Estruje las prendas para eliminar la mayor cantidad de agua posible.
Prendas especiales ES • Cantidad de ropa: prendas individuales y pequeñas cargas pueden requerir más tiempo para secarse. Mantas y cubrecama: las prendas de acrílico (Acilian, Courtelle, Orion, Dralon) deben secarse con absoluto cuidado a temperatura baja. No programe tiempos de secado prolongados. • Secado: si las prendas deben ser planchadas es posible extraerlas de la máquina cuando aún están húmedas. Las prendas que deben estar totalmente secas pueden dejarse más tiempo.
Advertencias y sugerencias ! Este electrodoméstico ha sido diseñado y fabricado re- spetando las normas internacionales sobre seguridad. Estas advertencias se suministran por motivos de seguridad y deben ser cumplidas atentamente. Seguridad general • La parte final de un ciclo de la máquina secadora se realiza sin calor (ciclo de enfriamiento) para asegurarse que la ropa quede a una temperatura que no la afecte.
Cuidados y mantenimiento ES Interrupción de la alimentación eléctrica ! Desconecte la secadora cuando no esté funcionando, del mismo modo durante las operaciones de limpieza y mantenimiento. Limpieza del filtro después de cada ciclo El filtro es un componente fundamental del secado: su función es la de recoger los residuos de lana y la pelusa que se forman durante el secado. Al finalizar el secado limpie el filtro aclarándolo debajo de agua corriente o limpiándolo con una aspiradora.
Problemas y soluciones Cuando tenga la sensación de que la secadora no funciona de forma correcta, antes de llamar al Centro de asistencia técnica (ver Asistencia Técnica) consulte atentamente las siguientes sugerencias para la solución de los problemas. ES Problema: La secadora no arranca. El ciclo de secado no comienza. Los tiempos de secado son prolongados. El piloto “Vaciar cubeta” centellea, pero la secadora funciona desde hace poco tiempo.
Asistencia Técnica ES Antes de llamar al Centro de asistencia técnica: Repuestos • Consulte la guía para la solución de los problemas para ver si es posible solucionar la avería personalmente (ver Problemas y soluciones). • De lo contrario, apague la secadora y llame al Centro de asistencia técnica más cercano. Esta secadora es una máquina compleja.
Instruções para a utilização MÁQUINA DE SECAR ROUPA Índice PT Informações importantes, 50-51 PT Português Instalação, 52 Onde instalar a máquina de secar roupa Ventilação Ligação eléctrica Informações preliminares Descrição da máquina de secar roupa, 53-54 Características Painel de comandos Como efectuar uma secagem, 55 Início e escolha do programa Programas e opções, 56-57-58 IDCA G35 Tabela dos programas Programas especiais Opções Abertura da porta Roupa, 59-60 Triagem da roupa Etiquetas de man
Informações importantes PT Para um funcionamento eficiente da máquina de secar roupa por condensação, é necessário respeitar o esquema de manutenção regular indicado abaixo: no fim de cada ciclo de secagem tem influência sobre os desempenhos da máquina, que demora mais tempo a secar e, consequentemente, consome mais electricidade durante a secagem. Filtro de cotão – É NECESSÁRIO limpar o cotão que se deposita no filtro no fim de cada ciclo de secagem.
Unidade de condensação - É necessário limpar o cotão do condensador todosos meses. PT Fase 1 Abra a tampa do condensador - Segure a pega e puxe-a na sua direcção. Fase 2 Retire o condensador rodando as 3 molas e, em seguida, puxe o condensador na sua direcção. (É possível que exista água nos tubos: é normal). Fase 3 Limpe o condensador com água, fazendo-a escorrer pela parte posterior para remover eventuais depósitos de cotão. Fase 4 Reinstale a unidade de condensação.
Instalação Onde instalar a máquina de secar roupa? • As chamas podem danificar a máquina de secar roupa, que deve pois ser instalada num local afastado de fogões a gás, aquecedores, radiadores ou placas de cozinha. 15 mm 15 mm Se o electrodoméstico for instalado sob uma banca, é necessário deixar um espaço de 10 mm entre o painel superior do electrodoméstico e outros objectos colocados sobre o mesmo, e um espaço de 15 mm entre os lados do electrodoméstico e as paredes ou os móveis vizinhos.
Descrição da máquina de secar roupa Características Abertura da porta PT Placa dos dados de exercício Recipiente de recolha da água Pressione a porta Número de série e número do modelo Filtro Grelha da admissão de ar Unidade de condensação (tampa aberta) Pega da tampa do condensador (puxe para abrir) Painel de comandos Botão On/Off Selector de Programas Botões e indicadores luminosos Opções Botão e indicador luminoso START/PAUSE Indicadores luminosos de manutenção Indicadores luminosos fa
PT Botão ON/OFF/Reset Uma pressão normal do botão liga ou desliga o aparelho. Se a máquina de secar roupa estiver funcionando, uma pressão prolongada por aproximadamente 3 segundos fará desligar o aparelho e restabelecer o ciclo em curso. Selector de Programas Consente configurar o programa: rode até que o indicador fique direccionado para o programa pretendido (consulte Início e Escolha do programa). Botões opções Permitem escolher as opções disponíveis para o programa seleccionado.
Como efectuar uma secagem Início e escolha do programa PT 1. Introduza a ficha da máquina de secar roupa na tomada de alimentação eléctrica. 2. Seleccione a roupa em função do tipo de roupa (consulte Roupa). 3. Abra a porta e certifique-se de que o filtro está limpo e em posição, e que o recipiente de recolha da água está vazio e posicionado correctamente (consulte Manutenção). 4. Carregue a máquina tendo o cuidado de não deixar nenhuma peça de roupa entre a porta e o respectivo vedante. Feche a porta. 5.
Programas e opções PT Tabela dos programas Programa Carga máx. (kg) Opções compatíveis Duração do ciclo Energy Saver 1 Eco Algodão 1 Pré antidobras - Pós antidobras - Início retardado. 30’ 2 Eco Camisas 1 Pré antidobras - Pós antidobras - Início retardado. 30’ 3 Eco Sintéticos 1 Pré antidobras - Pós antidobras - Início retardado. 30’ 4 Algodão Extra Máx. Pré antidobras - Pós antidobras - Início retardado. 160’ 5 Algodão Armário Máx. Pré antidobras - Pós antidobras - Início retardado.
Programa Lã Este programa destina-se às peças de roupa que suportam a secagem em tambor, identificadas com o símbolo . Pode ser utilizado para cargas de até1 kg (cerca de 3 blusões). É aconselhável colocar as peças do avesso antes da secagem. Este programa demora cerca de 60 minutos, mas pode durar mais tempo, dependendo das dimensões e da densidade da carga e da velocidade de centrifugação usada na máquina de lavar roupa.
PT Opções As opções consentem personalizar o programa seleccionado conforme as próprias exigências. Início posteior O início de alguns programas (consulte Programas e opções) pode ser retardado até 9 horas. Pressione várias vezes o botão até alcançar o tempo de atraso de desejado. Antes de definir um início retardado, certifique-se de que o recipiente de recolha da água está vazio e que o filtro está limpo.
Roupa Triagem da roupa Etiquetas de manutenção • Verifique os símbolos que constam das etiquetas das diversas peças para se certificar de que podem ser submetidas a secagem em tambor. • Efectue a triagem da roupa consoante o tipo de tecido. • Esvazie os bolsos e verifique os botões. • Feche os fechos de correr e outros fechos e ate os cintos e os laços sem apertar demasiado. • Torça as peças de roupa para eliminar a maior quantidade de água possível.
PT Peças especiais pode retirá-las da máquina quando ainda estão um pouco húmidas. Por seu turno, as peças de roupa que são para secar completamente podem ficar na máquina durante mais tempo. Cobertores e colchas: as peças de acrílico (Acilian, Courtelle, Orion, Dralon) devem ser secas com extremo cuidado a uma temperatura baixa. Não defina tempos longos de secagem. • A temperatura definida.
Advertências e sugestões ! Este electrodoméstico foi concebido e fabricado em conformida- de com as normas internacionais em matéria de segurança. Estas advertências são fornecidas por razões de segurança e devem ser observadas com atenção. Segurança geral • A parte final de um ciclo da máquina de enxugar roupa ocorre sem calor (ciclo de arrefecimento) para garantir que a carga permaneça a uma temperatura que não lhe cause danos.
Cuidados e manutenção PT Interrupção da alimentação eléctrica ! Desligue a máquina de secar roupa quando não estiver a funcionar, bem como durante as operações de limpeza e de manutenção. Limpeza do filtro no fim de cada ciclo O filtro é um componente fundamental para a secagem: a sua função consiste em recolher os resíduos de lã e o cotão que se formam durante a secagem. No fim da secagem, limpe o filtro enxaguando-o com água corrente ou limpando-o com o aspirador.
Problemas e soluções Se lhe parecer que a máquina de secar roupa não está a funcionar correctamente, antes de contactar o Centro de Assistência (consulte Assistência), consulte atentamente as seguintes sugestões para a resolução dos problemas. PT Problema: A máquina de secar roupa não arranca. Possíveis causas/ Soluções: • • • • A ficha não ficou bem encaixada na tomada eléctrica para que possa fazer contacto. Ocorreu um corte de corrente. O fusível está queimado.
Assistência 195102210.00 04/2012 - Xerox Fabriano PT Antes de contactar o Centro de Assistência: Peças de reposição • Siga o guia de resolução de problemas para tentar resolver a avaria pessoalmente (consulte Problemas e soluções). • Caso contrário, desligue a máquina e contacte o Centro de Assistência mais próximo de si. Esta máquina de secar roupa é uma máquina complexa.