Mode d’emploi SÈCHE-LINGE Table des matières FR Français EN English,17 FR Informations importantes, 2-3 Installation, 4 Où installer le sèche-linge Ventilation Raccordement électrique Informations préliminaires Description du sèche-linge, 5-6 Caractéristiques Tableau de bord Comment effectuer un cycle de séchage, 7 Démarrage et choix du programme Programmes et options, 8-9-10 IDCA H G35 B Tableau des programmes Programmes spéciaux Options Ouverture de la porte Linge, 11-12 Tri du linge Étiquettes
Informations importantes FR Pour assurer le bon fonctionnement du sèche-linge à condensation il faut suivre le schéma d’entretien ordinaire indiqué ci-dessous : Filtre à peluches – IL EST NÉCESSAIRE d’éliminer les peluches qui s’accumulent sur le filtre après chaque cycle de séchage. Étape 1 Ouvrez la porte du sèche-linge en appuyant comme illustré par la figure.
Groupe condenseur - Il est nécessaire d’éliminer les peluches accumulées sur le condenseur tous les mois. FR Étape 1 Ouvrez le couvercle du condenseur - tirez la poignée vers vous. Étape 2 Enlevez le condenseur en tournant les 3 clips, ensuite tirez le condenseur vers vous. (Dans les tuyaux il pourrait y avoir encore de l’eau : cela est normal).
Installation Raccordement électrique • Placez votre sèche-linge à une certaine distance des cuisinières, fourneaux, radiateurs, ou plaques de cuisson à gaz, car les flammes peuvent endommager cet appareil. Si vous installez cet appareil 15 mm sous un plan de travail, faites 15 mm en sorte de laisser un espace de 10 mm entre le dessus de l’appareil et tout autre objet sur ou au-dessus de celui-ci, et un espace de 15 mm entre ses côtés et les éléments d’ameublement ou les murs latéraux.
Description du sèche-linge Caractéristiques Ouverture de la porte Plaque signalétique de l’appareil Réservoir d’eau Appuyez sur la porte FR Numéro de série et référence du modèle Filtre Grille d’entrée d’air Groupe condenseur (couvercle ouvert) Poignée du couvercle du condenseur (tirez pour ouvrir) Tableau de bord Touche On/Off Bouton Programmes Touches et voyants Options Touche avec voyant Marche/Pause Voyants d’entretien Voyants des phases de séchage ou de départ différé 5
FR Touche ON/OFF/Reset Une pression normale sur cette touche fait allumer ou éteindre l’appareil. Si le sèche-linge est en marche, une pression prolongée d’au moins 3 secondes fait éteindre l’appareil et remettre à zéro le cycle en cours. Bouton Programmes Permet de sélectionner les programmes : tournez le bouton jusqu’à positionner l’indicateur sur le programme souhaité (voir Démarrage et choix du programme). Touches options Permettent de choisir les options disponibles pour le programme sélectionné.
Comment effectuer un cycle de séchage Démarrage et choix du programme FR 1. Branchez la fiche du sèche-linge dans la prise de courant électrique. 2. Sélectionnez le programme en fonction du type de linge (voir Linge). 3. Ouvrez la porte et assurez-vous que le filtre est propre et en place et que le réservoir d’eau est vide et en place (voir Entretien). 4. Chargez la machine en faisant attention à ce qu’aucun vêtement ne s’interpose entre la porte et le joint de la porte. Fermez la porte. 5.
Programmes et options FR Tableau des programmes Programme Charge maxi (Kg) Options compatibles Durée cycle Energy Saver 1 Eco Coton 1 Anti-froissement - Départ différé. 30’ 2 Eco Chemises 1 Anti-froissement - Départ différé. 30’ 3 Eco Synthétiques 1 Anti-froissement - Départ différé. 30’ Coton 4 Coton Standard Max. Repassage facile - Anti-froissement - Départ différé. 150’ 5 Coton intensif Max. Anti-froissement - Départ différé. 160’ 6 Coton sur cintre Max.
Programme Laine C’est un programme réservé aux articles supportant le séchage au tambour et portant le symbole . Vous pouvez l’utiliser pour des charges jusqu’à 1 kg (3 pull-overs environ). Il est conseillé de tourner les vêtements à l’envers avant de les charger dans le sèche-linge. Ce programme prend 1:00 (hrs:mins) environ, mais parfois cette durée se prolonge, selon les dimensions de la charge, sa densité et la vitesse d’essorage du lave-linge.
FR Options Les options permettent de personnaliser le programme sélectionné en fonction de vos exigences. Haute température Si un séchage temporisé est sélectionné, appuyez sur cette touche pour régler une Haute température. Le voyant au-dessus de la touche s’allume. Les programmes minutés sont par défaut réglés sur une température douce.
Linge Tri du linge Étiquettes d’entretien • Vérifiez les symboles sur les étiquettes des vêtements pour vous assurer que les articles peuvent être passés au sèche-linge. • Triez votre linge par type de textile. • Videz les poches et contrôlez les boutons. • Fermez les fermetures éclair et les crochets et attachez les ceintures et les cordons, sans serrer. • Essorez chaque article de manière à éliminer autant d’eau que possible.
FR Linge ou vêtements particuliers • La quantité de linge : les articles uniques ou les petites charges peuvent prendre plus longtemps à sécher. Couvertures et dessus de lits : les articles en acrylique (Acilan, Courtelle, Orion, Dralon) doivent être séchés avec des précautions particulières, à basse température. Évitez de les sécher pendant une durée prolongée.
Précautions et conseils ! Cet électroménager a été conçu et réalisé conformément aux normes internationales de sécurité. Ces consignes sont fournies pour des raisons de sécurité, il faut les respecter scrupuleusement.
Soin et entretien FR Interruption de l’alimentation électrique ! Débranchez votre sèche-linge lorsque vous ne l’utilisez pas, lorsque vous le nettoyez et durant toutes les opérations d’entretien. Nettoyage du filtre après chaque cycle Le filtre est une pièce importante de votre sèche-linge : il accumule des peluches qui se forment durant le séchage. Par conséquent, une fois le séchage terminé, nettoyez le filtre en le rinçant sous l’eau courante ou avec votre aspirateur.
Problèmes et solutions FR Si vous trouvez que le sèche-linge ne fonctionne pas correctement, avant de contacter le Service après-vente (voir Assistance), consultez attentivement le tableau suivant afin de pouvoir résoudre les problèmes éventuels : Problème : Causes / Solutions possibles : Le sèche-linge ne démarre pas. • La fiche n’est pas suffisamment insérée dans la prise murale pour qu’il y ait contact. • Il y a une panne de courant. • Le fusible a sauté.
Assistance FR Avant d’appeler le Centre de Service après-vente : Pièces détachées • Suivez le guide d’aide à la résolution des problèmes pour voir si vous n’arrivez pas à résoudre le problème vous-même (voir Problèmes et solutions). • Dans le cas contraire, éteignez votre sèche-linge et contactez le Centre de Service après-vente le plus proche. Ce sèche-linge est un appareil complexe.
Instruction manual TUMBLE DRYER Contents EN Important information, 18-19 EN English Installation, 20 Where to install the tumble dryer Ventilation Electrical connections Preliminary information Description of the tumble dryer, 21-22 Features Control panel How to carry out a drying cycle, 23 Starting and selecting a programme Programmes and options, 24-25-26 IDCA H G35 B Programme chart Special programmes Options Opening the door Laundry, 27-28 Sorting laundry Care labels Special items Drying times
Important information EN To ensure that the condenser dryer functions efficiently, the following routine maintenance procedures must be carried out: Fluff filter – CLEAN off any fluff build-up on the filter after each drying cycle. Failure to clean the filter after each drying cycle can undermine drying performance as the machine takes longer to dry and thus consumes more energy. Water container – empty the water container after each drying cycle.
Condenser unit - remove any fluff build-up from the condenser on a monthly basis. EN Step 1 Open the condenser cover - grip the handle and pull towards you. Step 2 Remove the condenser by turning the 3 catches, then pull the condenser towards you. (It is normal for some residual water to be left in the tubes). Product Data Rated capacity of cotton laundry for the "standard cotton programme" at full load - kg Step 3 Clean the condenser with running water over the rear side to remove any fluff deposits.
Installation Electrical connections • Install the dryer far from gas ranges, stoves, radiators or hobs, as flames may damage it. If the dryer is installed below a worktop, ensure there are 10 mm between the upper panel of the dryer and any objects above it, and 15 mm between the sides of the machine and the walls or furniture units adjacent to it. This ensures adequate air circulation. Before plugging the appliance into the socket, check the following: • Make sure your hands are dry.
Description of the tumble dryer Features Opening the door EN Rating plate Water container Press the door Model & Serial Numbers Filter Air intake grille Condenser unit (cover open) Condenser cover handle (pull to open) Control panel On/Off button Programme selection knob Options buttons and indicator lights Start/Pause button and indicator light Maintenance indicator lights Drying phase or Delay timer indicator lights 21
EN ON/OFF/Reset button Pressing the button normally will cause the machine to switch on or off. If the button is pressed for 3 seconds while the dryer is in function, the machine will switch off and the running cycle will reset. Programme selection knob Allows for setting the programme: turn until the indicator points towards desired programme (see Starting and selecting a programme). Options buttons Allow for selecting the options available for the selected programme.
How to carry out a drying cycle Starting and selecting a programme EN 1. Plug the dryer into the power supply socket. 2. Select the programme according to the type of laundry (see Laundry). 3. Open the door, ensure that the filter is clean and securely placed and that the water container is empty and correctly slotted (see Care and maintenance). 4. Load the machine, making sure that no piece of laundry gets between the door and the relative seal. Close the door. 5.
Programmes and options EN Programme chart Programme Max. load (kg) Compatible options Cycle duration Energy Saver 1 Eco Cotton 1 Anti Crease - Delay timer 30’ 2 Eco Shirts 1 Anti Crease - Delay timer 30’ 3 Eco Synthetics 1 Anti Crease - Delay timer 30’ Cotton 4 Stardard Cotton Max. Fast Iron - Anti Crease - Delay timer 150’ 5 Ready to Wear Max. Anti Crease - Delay timer 160’ 6 Cotton Hanger Max.
Wool Programme This programme is specific for items that withstand tumble drying and are labelled with the symbol. It is suitable for loads of up to 1 kg (about 3 jerseys). We recommend turning the garments inside out before drying them. This programme lasts about 60 minutes, although it may last longer depending on the size and density of the load and on the spin speed used during the wash cycle.
EN Options The options allow for customising the selected programme according to one’s own needs. High Heat When a drying time is selected, pressing this button sets high heat drying and the indicator light above the button lights up. The timed programmes are pre-set to low heat. Fast Iron This option, when selected, delivers for the cycle chosen the best humidity level to help make ironing quicker and easier. In this way it is possible to achieve a level of additional drying. (see Programmes and options).
Laundry Sorting laundry Care labels • Check the symbols on the care labels of the various garments to verify whether the garments can be safely tumble dried. • Sort laundry according to the type of fabric. • Empty all pockets and check for loose buttons. • Close zips and hooks and fasten belts and strings without tightening them. • Wring out garments to remove the maximum amount of water possible. Always check the care labels, especially when placing garments in the tumble dryer for the first time.
EN Special items • Amount of laundry: single items and small loads may take longer to dry. Blankets and bedcovers: acrylic items (Acilian, Courtelle, Orion, Dralon) must be dried with great care at low heat. Avoid drying for long periods. • Drying: if items are to be ironed, they can be removed from the dryer while still slightly damp. Items that require complete drying can be left longer. Creased or pleated garments: read the drying instructions supplied by the manufacturer. • Heat setting.
Warnings and suggestions ! This appliance has been designed and built according to international safety standards. These warnings are given for safety reasons and must be followed carefully. General safety • The final part of a tumble dryer cycle occurs without heat (cooling cycle) to ensure that the laundry is not damaged due to excessive temperatures.
Care and maintenance EN Disconnecting the power supply ! Disconnect the dryer when not in use or during cleaning and maintenance operations. Cleaning the filter after each cycle The filter is a fundamental component of the dryer: its function is to collect lint and fluff that form during drying. Clean the filter once drying is completed, by rinsing it under running water or cleaning it with a vacuum cleaner.
Troubleshooting If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the Technical Assistance Centre (see Assistance). EN Problem: Possible causes / Solutions: The dryer does not start. • • • • • • • The drying cycle does not start. • A delayed start time has been set (see Programmes and options). • The START/PAUSE button has been pressed; a short delay follows before the dryer starts running.
Assistance 08/2013 - Xerox Fabriano EN Before contacting the Technical Assistance Centre: Spare parts • Follow the troubleshooting guide to check whether problems can be solved personally (see Troubleshooting). • If not, switch the dryer off and contact the Technical Assistance Centre closest to you. This dryer is a complex machine.