Instructions for use WASHING MACHINE Contents GB English,1 DE Deutsch,37 IT Italiano,13 CZ Česky,49 UA Українська,73 PL Polski,25 SK Slovensky,61 GB Installation, 2-3 Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data Care and maintenance, 4 Cutting off the water or electricity supply Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hos
Installation GB ! This instruction manual should be kept in a safe place for future reference. If the washing machine is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/ herself with its operation and features. ! Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance. Unpacking and levelling Unpacking 1.
Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a drainage duct or a wall drain located at a height between 65 and 100 cm from the floor; alternatively, rest it on the side of a washbasin or bathtub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater.
Care and maintenance GB Cutting off the water and electricity supplies • Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washing machine and help to prevent leaks. • Unplug the washing machine when cleaning it and during all maintenance work. 2. unscrew the lid by rotating it anticlockwise (see figure): a little water may trickle out.
Precautions and tips ! This washing machine was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. GB General safety • This appliance was designed for domestic use only.
Description of the washing machine and starting a wash cycle GB Control panel WASH CYCLE PROGRESS DELAY TIMER button DISPLAY ON/OFF button FUNCTION buttons with indicator lights TEMPERATURE Detergent dispenser drawer knob Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”). ON/OFF button: switches the washing machine on and off. WASH CYCLE knob: programmes the wash cycles. During the wash cycle, the knob does not move.
Indicator lights The indicator lights provide important information. This is what they can tell you: Wash cycle phase indicator lights Once the desired wash cycle has been selected and has begun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress.
Wash cycles Max. load (kg) Residual dampness % Energy consumption kWh Total water lt Cycle duration Table of wash cycles 1 Cotton with prewash: extremely soiled whites.
Personalisation Setting the temperature GB Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles). The temperature may be lowered, or even set to a cold wash . The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value set for each wash cycle. ! Exception: if the 2 programme is selected, the temperature can be increased up to a value of 90°C.
Detergents and laundry GB Detergent dispenser drawer Garments requiring special care Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause build up on the inside of your appliance and contribute to environmental pollution. Silk: use special wash cycle 9 to wash all silk garments. We recommend the use of special detergent which has been designed to wash delicate clothes.
Troubleshooting Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be solved easily using the following list. GB Problem: Possible causes / Solutions: The washing machine does not switch on. • The appliance is not plugged into the socket fully, or is not making contact. • There is no power in the house. The wash cycle does not start. • • • • • The washing machine door is not closed properly.
Service GB Before calling for Assistance: • Check whether you can solve the problem alone (see “Troubleshooting”); • Restart the programme to check whether the problem has been solved; • If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate. ! Always request the assistance of authorised technicians. Have the following information to hand: • the type of problem; • the appliance model (Mod.); • the serial number (S/N).
Istruzioni per l’uso LAVABIANCHERIA Sommario I Italiano I Installazione, 14-15 Disimballo e livellamento Collegamenti idraulici ed elettrici Primo ciclo di lavaggio Dati tecnici Manutenzione e cura, 16 Escludere acqua e corrente elettrica Pulire la lavabiancheria Pulire il cassetto dei detersivi Curare oblò e cestello Pulire la pompa Controllare il tubo di alimentazione dell’acqua Precauzioni e consigli, 17 IWUD 41251 Sicurezza generale Smaltimento Descrizione della lavabiancheria e avviare un progra
Installazione I ! È importante conservare questo libretto per poterlo consultare in ogni momento. In caso di vendita, di cessione o di trasloco, assicurarsi che resti insieme alla lavabiancheria per informare il nuovo proprietario sul funzionamento e sui relativi avvertimenti. ! Leggere attentamente le istruzioni: ci sono importanti informazioni sull’installazione, sull’uso e sulla sicurezza.
Collegamento del tubo di scarico 65 - 100 cm Collegare il tubo di scarico, senza piegarlo, a una conduttura di scarico o a uno scarico a muro posti tra 65 e 100 cm da terra; oppure appoggiarlo al bordo di un lavandino o di una vasca, legando la guida in dotazione al rubinetto (vedi figura). L’estremità libera del tubo di scarico non deve rimanere immersa nell’acqua. ! Il cavo di alimentazione deve essere sostituito solo da tecnici autorizzati.
Manutenzione e cura I Escludere acqua e corrente elettrica • Chiudere il rubinetto dell’acqua dopo ogni lavaggio. Si limita così l’usura dell’impianto idraulico della lavabiancheria e si elimina il pericolo di perdite. • Staccare la spina della corrente quando si pulisce la lavabiancheria e durante i lavori di manutenzione. Pulire la lavabiancheria La parte esterna e le parti in gomma possono essere puliti con un panno imbevuto di acqua tiepida e sapone. Non usare solventi o abrasivi.
Precauzioni e consigli ! La lavabiancheria è stata progettata e costruita in conformità alle norme internazionali di sicurezza. Queste avvertenze sono fornite per ragioni di sicurezza e devono essere lette attentamente. Sicurezza generale • Questo apparecchio è stato concepito esclusiva- mente per un uso di tipo domestico. • e riciclaggio dei materiali che li compongono ed impedire potenziali danni per la salute e l’ambiente.
Descrizione della lavabiancheria e avviare un programma I Pannello di controllo Tasto PARTENZA RITARDATA Tasto ON/OFF DISPLAY Manopola AVVIO/ PAUSA OPZIONE Spia TEMPERATURA PROGRAMMI Tasto e spia Tasti e spie Manopola Cassetto dei detersivi SPIE AVANZAMENTO CICLO Manopola OBLÒ BLOCCATO CENTRIFUGA Cassetto dei detersivi: per caricare detersivi e additivi (vedi “Detersivi e biancheria”). Spia OBLÒ BLOCCATO: per capire se l’oblò è apribile (vedi pagina a fianco).
Spie Le spie forniscono informazioni importanti. Ecco che cosa dicono: Spie fase in corso Una volta selezionato e avviato il ciclo di lavaggio desiderato, le spie si accenderanno progressivamente per indicarne lo stato di avanzamento: Spia oblò bloccato La spia accesa indica che l’oblò è bloccato per impedire l’apertura; per aprire l’oblò è necessario che la spia sia spenta (attendere 3 minuti circa).
Programmi Umidità residua % Consumo energia kWh Acqua totale lt Durata ciclo Descrizione del Programma Carico max.
Personalizzazioni Impostare la temperatura Ruotando la manopola TEMPERATURA si imposta la temperatura di lavaggio (vedi Tabella programmi). La temperatura si può ridurre sino al lavaggio a freddo ( ). La macchina impedirà automaticamente di impostare una temperatura maggiore a quella massima prevista per ogni programma. ! Eccezione: selezionando il programma 2 la temperatura può essere portata sino a 90°.
Detersivi e biancheria I Cassetto dei detersivi Sistema bilanciamento del carico Il buon risultato del lavaggio dipende anche dal corretto dosaggio del detersivo: eccedendo non si lava in modo più efficace e si contribuisce a incrostare le parti interne della lavabiancheria e a inquinare l’ambiente. Prima di ogni centrifuga, per evitare vibrazioni eccessive e per distribuire il carico in modo uniforme, il cestello effettua delle rotazioni ad una velocità leggermente superiore a quella del lavaggio.
Anomalie e rimedi Può accadere che la lavabiancheria non funzioni. Prima di telefonare all’Assistenza (vedi “Assistenza”), controllare che non si tratti di un problema facilmente risolvibile aiutandosi con il seguente elenco. Anomalie: Possibili cause / Soluzione: La lavabiancheria non si accende. • La spina non è inserita nella presa della corrente, o non abbastanza da fare contatto. • In casa non c’è corrente. Il ciclo di lavaggio non inizia. • • • • • L’oblò non è ben chiuso.
Assistenza I Prima di contattare l’Assistenza: • Verificare se l’anomalia può essere risolta da soli (vedi “Anomalie e rimedi”). • Riavviare il programma per controllare se l’inconveniente è stato ovviato; • In caso negativo, contattare il Numero Unico 199.199.199*. ! Non ricorrere mai a tecnici non autorizzati. Comunicare: • il tipo di anomalia; • il modello della macchina (Mod.); • il numero di serie (S/N).
Instrukcja obsługi PRALKA Spis treści PL Polski PL Instalacja, 26-27 Rozpakowanie i wypoziomowanie Podłączenia hydrauliczne i elektryczne Pierwszy cykl prania Dane techniczne Utrzymanie i konserwacja, 28 Odłączenie wody i prądu elektrycznego Czyszczenie pralki Czyszczenie szufladki na środki piorące Konserwacja okrągłych drzwiczek i bębna Czyszczenie pompy Kontrola przewodu doprowadzającego wodę Zalecenia i środki ostrożności, 29 IWUD 41251 Ogólne zasady bezpieczeństwa Utylizacja Opis pralki i uruc
Instalacja PL ! Należy zachować niniejszą książeczkę, aby móc z niej skorzystać w każdej chwili. W przypadku sprzedaży, odstąpienia lub przeniesienia pralki w inne miejsce należy zadbać o przekazanie instrukcji wraz z maszyną, aby nowy właściciel mógł zapoznać się z działaniem urządzenia i z dotyczącymi go ostrzeżeniami. ! Należy uważnie przeczytać instrukcję obsługi: zawiera ona ważne informacje dotyczące instalacji oraz właściwego i bezpiecznego użytkowania pralki.
Podłączenie przewodu odpływowego 65 - 100 cm Podłączyć przewód o d p ł y w o w y, n i e zginając go, do rury ściekowej lub do otworu odpływowego w ścianie, które powinny znajdować się na wysokości od 65 do 100 cm od podłogi; ewentualnie oprzeć go na brzegu zlewu lub wanny, przymocowując do kranu prowadnik, znajdujący się w wyposażeniu (patrz rysunek). Wolny koniec przewodu odpływowego nie powinien być zanurzony w wodzie.
Utrzymanie i konserwacja PL Odłączenie wody i prądu elektrycznego • Zamknąć kurek dopływu wody po każdym praniu. W ten sposób zmniejsza się zużycie instalacji hydraulicznej pralki oraz eliminuje się niebezpieczeństwo wycieków. • Przed przystąpieniem do czyszczenia pralki oraz do czynności konserwacyjnych wyjąć wtyczkę z gniazdka. Czyszczenie pralki Obudowę zewnętrzną i gumowe części pralki można myć ściereczką zmoczoną w letniej wodzie z mydłem.
Zalecenia i środki ostrożności ! Pralka została zaprojektowana i wyprodukowana zgodnie z międzynarodowymi normami bezpieczeństwa. Niniejsze ostrzeżenia zostały tu zamieszczone ze względów bezpieczeństwa i należy je uważnie przeczytać. Ogólne zasady bezpieczeństwa • Urządzenie to zostało zaprojektowane wyłącznie do użytkowania w warunkach domowych. Przekreślony symbol „kosza” umieszczony na produkcie przypomina klientowi o obowiązku specjalnego sortowania.
Opis pralki i uruchamianie programu PL Panel sterowania URUCHOMIENIE OPÓZNIONE Przycisk ON/OFF Szufladka na środki piorące Przyciski z kontrolkami FUNKCJI Pokrętło TEMPERATURY Pokrętło PROGRAMÓW Szufladka na środki piorące: do dozowania środków piorących i dodatków (patrz „Środki piorące i bielizna”). Przycisk ON/OFF: do włączania i wyłączania pralki. Pokrętło PROGRAMÓW: do ustawiania programów. W czasie trwania programu pokrętło pozostaje nieruchome.
Kontrolki Kontrolki dostarczają ważnych informacji. Oto co sygnalizują: Kontrolki bieżącej fazy prania: Po wybraniu i uruchomieniu żądanego cyklu prania kontrolki będą się kolejno zapalać, wskazując stan zaawansowania programu: Kontrolka blokady okrągłych drzwiczek Włączona kontrolka wskazuje, że drzwiczki zostały zablokowane w celu uniemożliwienia ich otwarcia; aby można było otworzyć drzwiczki, kontrolka musi być wyłączona; (odczekać około 3 minuty).
Programy Bawełna 40°C (2): tkaniny białe i kolorowe, delikatne, lekko zabrudzone. Białe syntetyki: tkaniny kolorowe, wytrzymałe, mocno zabrudzone. Białe syntetyki (3): tkaniny kolorowe, wytrzymałe, lekko zabrudzone. Kolorowa bawełna: tkaniny białe lekko zabrudzone i delikatne kolorowe. 90° 60° (Max.
Personalizacja Ustawianie temperatury Obracając pokrętłem TEMPERATURA ustawia się temperaturę prania (patrz Tabela programów). Temperaturę można zmniejszać, aż do prania w zimnej wodzie . Pralka automatycznie uniemożliwi ustawienie temperatury wyższej od maksymalnej temperatury przewidzianej dla danego programu. ! Wyjątek: wybierając program 2 temperaturę można podnieść aż do 90°. Ustawianie wirowania Obracając pokrętłem WIROWANIE ustawia się prędkość wirowania dla wybranego programu.
Środki piorące i bielizna PL Szufladka na środki piorące Dobry rezultat prania zależy również od prawidłowego dozowania środka piorącego: użycie jego nadmiernej ilości nie poprawia skuteczności prania, lecz przyczynia się do powstawania nalotów na wewnętrznych częściach pralki i do zanieczyszczania środowiska. ! Nie stosować środków do prania ręcznego, ponieważ tworzą one za dużo piany.
Nieprawidłowości w działaniu i sposoby ich usuwania Może się zdarzyć, że pralka nie działa. Przed wezwaniem Serwisu Technicznego (patrz „Serwis Techniczny”) należy sprawdzić, czy problemu nie da się łatwo rozwiązać przy pomocy poniższego wykazu. PL Nieprawidłowości w działaniu: Możliwe przyczyny / Rozwiązania: Pralka nie włącza się. • Wtyczka nie jest włączona do gniazdka lub jest wsunięta za słabo, tak że nie ma styku. • W domu nastąpiła przerwa w dostawie prądu. Cykl prania nie rozpoczyna się.
Serwis Techniczny PL Przed skontaktowaniem się z Serwisem Technicznym: • Sprawdzić, czy problemu nie można rozwiązać samodzielnie (patrz „Nieprawidłowości w działaniu i sposoby ich usuwania”); • Ponownie uruchomić program i sprawdzić, czy problem nie zniknął; • Jeśli nie, zwrócić się do autoryzowanego Serwisu Technicznego, dzwoniąc pod numer podany w karcie gwarancyjnej. ! Nigdy nie wzywać nieautoryzowanych techników. Należy podać: • rodzaj nieprawidłowości; • model maszyny (Mod.); • numer seryjny (S/N).
Bedienungsanleitungen WASCHVOLLAUTOMAT INHALTSVERZEICHNIS DE Deutsch DE Installation 38-39 Auspacken und Aufstellen Wasser- und Elektroanschlüsse Erster Waschgang Technische Daten Reinigung und Pflege 40 Abstellen der Wasser- und Stromversorgung Reinigung des Gerätes Reinigung der Waschmittelschublade Pflege der Gerätetür und Trommel Reinigung der Pumpe Kontrolle des Wasserzulaufschlauchs Vorsichtsmaßregeln und Hinweise 41 IWUD 41251 Allgemeine Sicherheit Entsorgung Beschreibung des Waschvollautomate
Installation DE ! Es ist äußerst wichtig, diese Bedienungsanleitung sorgfältig aufzubewahren, um sie jederzeit zu Rate ziehen zu können. Sorgen Sie dafür, dass sie im Falle eines Umzugs oder einer Übergabe an einen anderen Benutzer das Gerät stets begleitet, damit auch der neue Inhaber die Möglichkeit hat, diese zu Rate zu ziehen. ! Lesen Sie die Hinweise bitte aufmerksam durch, sie liefern wichtige Informationen hinsichtlich der Installation, des Gebrauchs und der Sicherheit.
Anschluss des Ablaufschlauches Schließen Sie den Ablaufschlauch ohne ihn dabei abzuknicken an einen geeigneten Abfluss an. Die Minde65 - 100 cm stablaufhöhe beträgt 65 - 100 cm (gemessen vom Boden), oder hängen Sie diesen mittels des Schlauchhalters gesichert in ein Becken oder Wanne ein; Befestigen Sie diesen mittels des mitgelieferten Schlauchhalters z.B. an einen Wasserhahn (siehe Abbildung). Das freie Ablaufschlauchende darf nicht unter Wasser positioniert werden.
Reinigung und Pflege DE Abstellen der Wasser- und Stromversorgung • Drehen Sie den Wasserhahn nach jedem Waschvorgang zu. Hierdurch wird der Verschleiß der Wasseranlage verringert und Wasserlecks vorgebeugt. • Ziehen Sie den Netzstecker aus der Steckdose, bevor Sie Ihren Waschvollautomaten reinigen. Reinigung des Gerätes Die Gehäuseteile und die Teile aus Gummi können mit einem mit warmer Spülmittellauge angefeuchteten Tuch gereinigt werden.
Vorsichtsmaßregeln und Hinweise ! Der Waschvollautomat wurde nach den strengsten internationalen Sicherheitsvorschriften entworfen und gebaut. Nachstehende Hinweise werden aus Sicherheitsgründen geliefert und sollten aufmerksam gelesen werden. Allgemeine Sicherheit • Dieses Gerät wurde ausschließlich für den Einsatz im privaten Haushalt konzipiert.
Beschreibung des Waschvollautomaten und Starten eines Waschprogramms DE Bedienblende Kontrollleuchten Taste STARTZEIT- PROGRAMMABLAUF VORWAHL Taste ON/OFF DISPLAY Tasten mit Kontrollleuchten FUNKTIONEN Wählschalter Waschmittelschublade PROGRAMME Waschmittelschublade: für Waschmittel und Zusätze (siehe „Waschmittel und Wäsche“). Taste ON/OFF: Zum Ein- und Ausschalten Ihres Waschvollautomaten. Wählschalter PROGRAMME: Zur Wahl der Waschprogramme.
Kontrollleuchten Die Kontrollleuchten liefern wichtige Hinweise. Sie signalisieren: Laufende Programmphase Wurde das Waschprogramm gewählt und gestartet, leuchten die Kontrollleuchten nach und nach auf, und zeigen so den jeweiligen Programmstand an. Kontrollleuchte Gerätetür gesperrt: Ist diese Kontrollleuchte eingeschaltet, bedeutet dies, dass das Bullauge gesperrt ist; warten Sie, bis die Leuchte erlischt, um das Bullauge zu öffnen (etwa 3 Minuten).
Waschprogramme Programmdauer Wasser gesamt lt Energieverbrauch kWh Restfeuchtigkeit % Waschmittel Hauptwäsche Weichspüler Max. Schleuder Geschwindigkeit (U/min) Vorwäsche Beschreibung des Programms Max. Temp. (C°) Max. Beladungsmenge (kg) Programmtabelle Wasch-programme DE Standard (Daily) 1 Baumwolle vorwäsche: stark verschmutzte Kochwäsche. 2 Baumwolle standard 60° (1): stark verschmutzte Weiß- und farbechte Buntwäsche.
Personalisierungen Temperatureinstellung Drehen Sie den Wählschalter TEMPERATUREN, um die Waschtemperatur einzustellen (siehe Programmtabelle). Die Temperatur kann bis auf Kaltwäsche herabgesetzt werden. Der Waschvollautomat verhindert automatisch die Einstellung einer höheren Schleuderstufe, sollte diese die für das jeweilige Programm vorgeschriebene Höchstgeschwindigkeit übersteigen. ! Ausnahme: Wird das Waschprogramm 2 eingestellt, kann die Temperatur bis auf 90° erhöht werden.
Waschmittel und Wäsche DE Waschmittel und Wäsche Ein gutes Waschergebnis hängt auch von einer korrekten Waschmitteldosierung ab: Eine zu hohe Dosierung bedeutet nicht unbedingt reinere Wäsche, sie trägt nur dazu bei, die Maschineninnenteile zu verkrusten und die Umwelt zu belasten. ! Verwenden Sie keine Handwaschmittel, sie verursachen eine zu hohe Schaumbildung. ! Waschmittel in Pulverform für Baumwollweißwäsche, für die Vorwäsche und für Waschprogramme bei Temperaturen über 60°C verwenden.
Störungen und Abhilfe Bei Funktionsstörung: Bevor Sie sich an den Technischen Kundendienst wenden (siehe „Kundendienst“), vergewissern Sie sich zuerst, ob es sich nicht um eine Kleinigkeit handelt, die Sie selbst beheben können. Ziehen Sie hierzu nachstehendes Verzeichnis zu Rate. DE Störungen: Mögliche Ursachen / Lösungen: Der Waschvollautomat schaltet sich nicht ein. • Der Stecker steckt nicht in der Steckdose, oder nicht so, dass der Kontakt hergestellt wird. • Der Strom ist ausgefallen.
Kundendienst DE Bevor Sie sich an den Kundendienst wenden: • Sollten einige Kontrollen vorab selbst durchgeführt werden (siehe „Störungen und Abhilfe“); • Starten Sie daraufhin das Programm erneut, um sicherzustellen, dass die Störung auch wirklich behoben wurde; • Ist dies nicht der Fall, dann kontaktieren Sie den autorisierten Kundendienst unter der auf dem Garantieschein befindlichen Telefonnummer. ! Wenden Sie sich auf keinen Fall an nicht autorisierte Techniker.
Návod k použití PRAČKA Obsah CZ Česky CZ Instalace, 50-51 Rozbalení a vyrovnání do vodorovné polohy Připojení k elektrické a k vodovodní síti První prací cyklus Technické údaje Údržba a péče, 52 Uzavření přívodu vody a vypnutí elektrického napájení Čištění pračky Čištění dávkovače pracích prostředků Péče o dvířka a buben Čištění čerpadla Kontrola přítokové hadice na vodu Opatření a rady, 53 IWUD 41251 Základní bezpečnostní pokyny Likvidace Popis pračky a zahájení pracího programu, 54-55 Ovládací pa
Instalace CZ ! Je důležité uschovat tento návod tak, abyste jej mohli kdykoli konzultovat. V případě prodeje, darování nebo přestěhování pračky se ujistěte, že zůstane uložen v blízkosti pračky, aby mohl posloužit novému majiteli při seznámení s její činností a s příslušnými upozorněními. ! Pozorně si přečtěte uvedené pokyny: obsahují důležité informace týkající se instalace, použití a bezpečnosti při práci. Rozbalení a vyrovnání do vodorovné polohy Rozbalení 1. Rozbalte pračku. 2.
Připojení vypouštěcí hadice 65 - 100 cm Připojte vypouštěcí hadici, aniž byste ji ohýbali, k odpadovému potrubí nebo k odpadu ve stěně, který se nachází od 65 do 100 cm nad zemí; nebo ji uchyťte k okraji umývadla či vany a připevněte vodicí držák z příslušenství ke kohoutu (viz obrázek). Volný konec vypouštěcí hadice nesmí zůstat ponořený do vody.
Údržba a péče CZ Uzavření přívodu vody a vypnutí elektrického napájení • Po každém praní uzavřete přívod vody. Tímto způsobem dochází k omezení opotřebení pračky a ke snížení nebezpečí úniku vody. • Před zahájením čištění pračky a během operací údržby vytáhněte zástrčku napájecího kabelu z elektrické zásuvky. Čištění pračky Vnější části a části z gumy se mohou čistit hadrem navlhčeným ve vlažné vodě a saponátu. Nepoužívejte rozpouštědla ani abrazivní látky.
Opatření a rady ! Pračka byla navržena a vyrobena v souladu s platnými mezinárodními bezpečnostním předpisy. Tato upozornění jsou uváděna z bezpečnostních důvodů a je třeba si je pozorně přečíst. Základní bezpečnostní pokyny upozorňuje na povinnost odevzdat zařízení po skončení jeho životnosti do odděleného sběru. Spotřebitelé by měli kontaktovat příslušné místní úřady nebo svého prodejce ohledně informací týkajících se správné likvidace starého zařízení.
Popis pračky a zahájení pracího programu CZ Ovládací panel ODLOŽENÝ START Tlačítko ON/OFF DISPLEJ Kontrolky PRŮBĚHU PRACÍHO CYKLU FUNKČNÍ tlačítka s kontrolkami Otočný ovladač Dávkovač pracích prostředků TEPLOTY Otočný ovladač PROGRAMŮ Otočný ovladač ODSTŘEĎOVÁNÍ Tlačítko s kontrolkou START/ PAUSE Kontrolka ZABLOKOVANÁ DVÍŘKA Dávkovač pracích prostředků: slouží k dávkování pracích prostředků a přídavných prostředků (viz „Prací prostředky a prádlo“).
Kontrolky Kontrolky jsou zdrojem důležitých informací. Informují nás o následujících skutečnostech: Kontrolka aktuální fáze pracího programu: Po zvolení a zahájení požadovaného pracího cyklu dojde k postupnému rozsvícení kontrolek informujících o jeho průběhu.
Prací programy Aviváz Max. náplò (kg) Zbytková vlhkost % Spotøeba energie kWh Celkové mnoství vody lt Cycle duration 1200 4 53 1,46 44 140’ 2 Standardní program pro bavlnu pro praní při 60°C (1): silnì zneèištìné bílé a barevné prádlo z odolných tkanin.
Uživatelská nastavení Nastavení teploty CZ Otáčením otočného ovladače TEPLOTY se nastavuje teplota praní (viz Tabulka programů). Teplota může být postupně snižována až po praní ve studené vodě ( ). Zařízení automaticky zabrání nastavení vyšší teploty, než je maximální teplota pro každý prací program. ! Výjimka: při volbě programu 2 bude možné zvýšit teplotu až na 90°C. Nastavení odstřeďování Otáčením otočného ovladače ODSTŘEĎOVÁNÍ se nastavuje rychlost odstřeďování zvoleného pracího programu.
Prací prostředky a prádlo CZ Dávkovač pracích prostředků Dobrý výsledek praní závisí také na správném dávkování pracího prostředku: použití jeho nadměrného množství snižuje efektivitu praní a napomáhá tvorbě vodního kamene na vnitřních částech pračky a zvyšuje znečištění životního prostředí. ! Nepoužívejte prací prostředky určené pro ruční praní, protože způsobují tvorbu nadměrného množství pěny.
Poruchy a způsob jejich odstranění Může se stát, že pračka nebude fungovat. Dříve, než zatelefonujete na Servisní službu (viz „Servisní služba“), zkontrolujte, zda se nejedná o problém, který lze snadno vyřešit s pomocí následujícího seznamu. Poruchy: Možné příčiny / Způsob jejich odstranění: Pračku nelze zapnout. • Zástrčka není zasunuta v zásuvce nebo není zasunuta natolik, aby došlo ke spojení kontaktů. • V celém domě je vypnutý proud. Nedochází k zahájení pracího cyklu.
Servisní služba CZ Před přivoláním Servisní služby: • Zkontrolujte, zda nejste schopni poruchu odstranit sami (viz „Poruchy a způsob jejich odstranění“); • Opětovně uveďte do chodu prací program, abyste ověřili, zda byla porucha odstraněna; • V opačném případě se obraťte na Centrum servisní služby na telefonním čísle uvedeném na záručním listu. ! Nikdy se neobracejte s žádostí o pomoc na techniky, kteří nejsou k výkonu této činnosti oprávněni.
Návod na použitie PRÁČKA Obsah SK Slovensky SK Inštalácia, 62-63 Rozbalenie a vyrovnanie do vodorovnej polohy Pripojenie k elektrickej a k vodovodnej sieti Prvý prací cyklus Technické údaje Údržba a starostlivosť, 64 Uzavretie prívodu vody a vypnutie elektrického napájania Čistenie práčky Čistenie dávkovača pracích prostriedkov Starostlivosť o dvierka a bubon Čistenie čerpadla Skontrolujte prítokovú hadicu vodu Opatrenia a rady, 65 IWUD 41251 Základné bezpečnostné pokyny Likvidácia Popis práčky a z
Inštalácia SK ! Je veľmi dôležité uschovať tento návod kvôli prípadnému ďalšiemu použitiu. V prípade predaja, darovania alebo presťahovania práčky sa uistite, že zostane uložený v jej blízkosti, aby mohol poslúžiť novému majiteľovi pri oboznámení sa s činnosťou a s príslušnými upozorneniami. ! Pozorne si prečítajte uvedené pokyny: obsahujú dôležité informácie, týkajúce sa inštalácie, použitia a bezpečnosti pri práci. Rozbalenie a vyrovnanie do vodorovnej polohy Rozbalenie 1. Rozbaľte práčku. 2.
Pripojenie vypúšťacej hadice 65 - 100 cm Pripojte vypúšťaciu hadicu, bez toho aby ste ju ohli, k odpadovému potrubiu alebo k odpadu v stene, ktorý sa nachádza od 65 do 100 cm nad zemou; alebo ju uchyťte k okraju umývadla či vane, a pripevnite vodiaci držiak z príslušenstva ku kohútu (viď obrázok). Voľný koniec vypúšťacej hadice nesmie zostať ponorený do vody.
Údržba a starostlivosť SK Uzavretie prívodu vody a vypnutie elektrického napájania • Po každom praní uzatvorte prívod vody. Týmto spôsobom sa znižuje opotrebenie rozvodu vody zariadenia a znížuje sa nebezpečenstvo úniku vody. • Pred zahájením čistenia práčky a počas údržby je potrebné vytiahnuť zástrčku prívodného kábla zo zásuvky. Čistenie práčky Vonkajšie časti a časti z gumy môžu byť čistené utierkou navlhčenou vo vlažnej vode a saponáte. Nepoužívajte rozpúšťadlá alebo abrazívne prostriedky.
Opatrenia a rady ! Práčka bola navrhnutá a vyrobená v súlade s platný- mi medzinárodnými bezpečnostnými predpismi. Tieto upozornenia sú uvádzané z bezpečnostných dôvodov a je potrebné si ich pozorne prečítať. Základné bezpečnostné pokyny • Toto zariadenie bolo navrhnuté výhradne na použitie ako spotrebič. Symbol “prečiarknutej popolnice” na výrobku Vás upozorňuje na povinnosť odovzdať zariadenie po skončení jeho životnosti do oddeleného zberu.
Popis práčky a zahájenie pracieho programu SK Ovládací panel Kontrolky POSTUPU Tlačidlo PRACIEHO CYKLU ONESKORENÉHO ŠTARTU FUNKČNÉ Tlačidlo ON/OFF DISPLEJ tlačidlá s kontrolkami Otočný ovládač Dávkovač pracích prostriedkov TEPLOTY Otočný ovládač PROGRAMOV Otočný ovládač Tlačidlo s kontrolkou START/ PAUSE Kontrolka ZABLOKOVANIA DVIEROK ODSTREĎOVANIA Dávkovač pracích prostriedkov: slúži na dávkovanie pracích prostriedkov a prídavných prostriedkov (viď „Pracie prostriedky a prádlo“).
Kontrolky Kontrolký sú zdrojom dôležitých informácií. Informujú o nasledujúcich skutočnostiach: Kontrolky prebiehajúcej fázy Po zvolení a zahájení požadovaného pracieho cyklu dôjde k postupnému rozsvecovaniu kontroliek informujúcich o jeho postupe.
Pracie programy Max. nápln (kg) Zvyšková vlhkos % Spotreba energie kWh Voda celkom lt Doba trvania cyklu SK Pracie programy Tabuľka pracích programov 90° 60° (Max. 90°) 1200 4 53 1,46 44 140’ 1200 - 4 53 0,77 30,6 145’ Štandardný program pre bavlnu pri 40 °C (2) Znacne špinavé biele a farebné prádlo z chúlostivých tkanín.
Užívateľské nastavenia Nastavenie teploty SK Otáčaním otočného ovládača TEPLOTY sa nastavuje teplota prania (viď Tabuľka programov). Teplota môže byť postupne znižovaná až po pranie v studenej vode ( ). Zariadenie automaticky zabráni nastaveniu vyššej teploty ako je maximálna teplota pre každý prací program. ! Výnimka: pri volbe programu 2 bude možné zvýšit teplotu až na 90°C.
Pracie prostriedky a prádlo SK Dávkovač pracích prostriedkov Prádlo vyžadujúce osobitnú starostlivosť Dobrý výsledok prania závisí aj od správneho dávkovania pracieho prostriedku: použitie nadmerného množstva znižuje efektivitu prania a napomáha tvorbe vodného kameňa na vnútorných častiach práčky a zvyšuje znečistenie životného prostredia. Hodváb: použite príslušný program 9 na pranie všetkého prádla z hodvábu. Odporúča sa použitie pracieho prostriedku pre chúlostivé prádlo.
Poruchy a spôsob ich odstránenia Môže sa stať, že práčka nebude fungovať. Skôr, ako zatelefonujete na Servisnú službu viď „Servisná služba“) skontrolujte, či sa nejedná o problém ľahko odstrániteľný pomocou nasledujúceho zoznamu. Poruchy: Možné príčiny / Spôsob ich odstránenia: Pračku nie je možné zapnúť. • Zástrčka nie je zasunutá v elektrickej zásuvke, alebo nie je zasunutá dostatočne, aby došlo k spojeniu kontaktov. • V celom dome je vypnutý prúd. Nedochádza k zahájeniu pracieho cyklu.
Servisná služba SK Pred obrátením sa na Servisnú službu: • Skontrolujte, či nie ste schopní poruchu odstrániť sami (viď „Poruchy a spôsob ich odstránenia“); • Opätovne uveďte do chodu prací program, s cieľom overiť, či bola porucha odstránená; • V opačnom prípade sa obráťte na Centrum servisnej služby, na telefónnom čísle uvedenom na záručnom liste. ! Nikdy sa neobracajte so žiadosťou o pomoc na technikov, ktorí nie sú na vykonávanie tejto činnosti oprávnení.
Iнструкцiя з використання ПРАЛЬНА МАШИНА Зміст UA Українська UA Встановлення, 74-75 Розпакування та вирівн‘ювання Підключення води й електроенергії Перший цикл прання Технiчнi данi Чищення та догляд, 76 Відключення води й електричного живлення Очищення пральної машини Чищення касети для пральних засобів Догляд за люком та барабаном Чищення насосу Контроль труби подачі води Заходи безпеки та поради, 77 IWUD 41251 Загальна безпека Утилiзацiя Опис пральної машини та запуску програм, 78-79 Панель керув
Встановлення UA ! Необхідно зберігати дану брошуру, щоб мати нагоду звернутися до неї у будь-який момент. У випадку продажу, передачі іншій особі або переїзду переконайтеся, що інструкція перебуває разом із пральною машиною й новий власник може ознайомитися з її принципами роботи й відповідними запобіжними заходами. ! Уважно вивчіть інструкцію: в ній міститься важлива інформація щодо встановлення, використання та безпеки.
Підключення зливного шланга 65 - 100 cm П і д к л ю ч і т ь зливний шланг, не згинаючи його, до к аналізаційного каналу або до входу до так ого к аналу на стіні, на відстані від 65 до 100 см від підлоги; або покладіть його на край вмивальник а або ванни, поєднавши н а п р а в л я ю ч у, яка входить до комплекту постачання, до крану (див.малюнок). Не залишайте вільний кінець зливного шланга зануреним у воду. ! Використання подовжувача шланга не рекомендоване.
Догляд та очищення UA Відключення води й електричного живлення • Закривайте водопровідний кран після кожного прання. У такий спосіб зменшується знос гідравлічної частини машини й усувається небезпека протікання. • Виймайте штепсель з розетки під час миття машини та під час робіт з технічного обслуговування. Очищення пральної машини Зовнішня частина і гумові деталі можуть митися тканиною, змоченою у теплій воді й милі. Не використовуйте розчинники або абразивнi засоби.
Запобіжні заходи та поради ! Машину була спроектовано і вироблено у відповідності з міжнародними нормами безпеки. Це попередження надаються задля вашої безпеки, і тому їх треба уважно прочитати. Загальна безпека • Даний прилад спроектований виключно для побутового використання.
Опис пральної машини та процедури iз запуску програм UA Панель керування Кнопка ВIДСТРОЧЕНОГО ПУСКУ Кнопка ON/OFF Касета для пральних засобiв Ручка ПРОГРАМИ Касета з пральним засобом: для завантаження пральних засобiв та засобiв догляду (див. “Пральнi засоби та бiлизна”). Кнопка ON/OFF: для увiмкнення й вимкнення пральної машини Ручка ПРОГРАМИ: для задання бажаних програм. Під час програми ручка залишається нерухомою. Кнопки та індикаторні лампи ОПЦІЯ: для вибору наявних опцій.
Індикаторнi лампи Індикаторнi лампи надають важливу iнформацiю От на що вони вказують: Iндикаторнi лампи поточних операцiй Пiсля обрання та запуску бажаного циклу прання iндикаторнi лампи вмикаються по черзi, щоб вказати на стан програми: Iндикаторна лампа ЛЮК ЗАБЛОКОВАНО Увiмкнена iндикаторна лампа вказує на те, що люк заблокований; вiдкривати люк можна лише коли ця лампа не свiтиться.
Програми Таблиця програм Ïðîãðàìè UA Опис програми Макс. темп. (°C) Щоденнi (Daily) 1 Бавовна з попереднім пранням: білі надзвичайно забруднені. Пральний засіб Макс. Макс. швидкiсть заван- Тривалiсть (обертiв за циклу Пом’ таження Попереднє хвилину) (кг) Прання якшупрання вач 90° 60° (Max.
Налаштування пiд власнi потреби Встановлення температури UA Обертаючи ручку ТЕМПЕРАТУРИ, ви можете задати температуру прання (див. Таблицю програм). Ви можете знижувати температуру аж до прання в холоднiй водi ( ). Машина перешкоджатиме встановленню температури, яка перевищує максимально дозволену для кожної конкретної програми. ! Виключення: при виборі програми 2, температура може збільшитися до 90° градусів.
Пральні засоби та білизна UA Касета з пральним засобом Добрий результат прання залежить також вiд правильного дозування прального засобу: надлишок прального засобу приведе до неефективного прання та сприятиме утворенню накипу всереденi пральної машини, а також забрудненню довкiлля. ! Не використовуйте засоби для ручного прання, тому що вони утворюють надто багато піни. Витягнiть касету для пральних засобiв та додайте пральнi засоби або засоби з догляду, як 3 вказано нижче.
Несправності та засоби їх усунення Може так статися, що пральна машина не працюватиме. Перш ніж зателефонувати до служби Допомоги (див. “Допомога”), перевірте можливість легкого усунення проблеми за допомогою наступного списку. Несправності: Можливі причини/Рішення: Пральна машина не вмикається. • Штепсель не вставлений в електричну розетку або вставлений не до кiнця. • У будинку немає електроенергії. Цикл прання не розпочинається. • • • • • Люк погано закрито. Кнопку ON/OFF не було натиснуто.
Допомога 195111108.01 07/2013 - Xerox Fabriano UA Перш ніж звернутися по Допомогу: • Перевірте, чи можна самостійно вирішити проблему (див. “Несправності і засоби їх усунення”). • Перезапустіть програму, щоб перевірити, чи усунено несправність; • У протилежному випадку, зверніться до авторизованої служби технічної Допомоги за телефонним номером, вказаним на гарантійному сертифікаті. ! Звертайтеся виключно до уповноважених фахівців. Треба повідомити: • тип несправності; • модель машини (Мод.