Note: Read all instructions before proceeding with installation. All specifications are ± 1/4’’ and are subject to change without notice.
TABLE OF CONTENTS Product Registration Congratulations! Safety Instructions 3 4 5 Installation Instructions Pre-Installation Procedures 6 Structural Preparation 7 Plumbing 8 Rough-In Measurements 9 Electrical Installation 10 Electrical Wiring Schematics-Whirlpool and Heater 11 Optional Inline Heater Operating Instructions 12 On/Off Timer Control Instructions 12 Troubleshooting On/Off Timer Control 13 Optional Chromatherapy LED Light Instructions 13 Troubleshooting Chromatherapy LED Light 14 Integrally Ski
Aquatic Product Registration Information Your product warranty is registered and confirmed with Aquatic through the Serial Number on your unit. You do not need to contact Aquatic to confirm registration. Please fill out the information below and reference when contacting the distributor to expedite warranty claims. Owner Information: Model Name Serial Number (See Table of Contents for Location) Purchase Date Distributor 8101 E. Kaiser Blvd. • Anaheim, CA 92808 (800) 877-2005 • Fax (714) 998-5340 www.
congratulations! You have chosen one of the finest bath products in the world! Aquatic supports your purchase with strong commitments to quality and customer satisfaction. Please read and follow all of the instructions contained in this Owner’s Manual before installing, operating or maintaining your whirlpool. In addition, you should continually refer to these instructions during the life of your whirlpool. Failure to comply with these instructions may invalidate your warranty.
IMPORTANT SAFETY INSTRUCTIONS warning: when using this unit, these basic precautions should be followed. This manual contains information and instructions for proper operation and maintenance of your whirlpool. Failure to follow these instructions could result in personal injury, electrical shock or fire. READ AND FOLLOW ALL INSTRUCTIONS danger! To reduce the risk of injury: A. Do not permit children to use this unit unless they are closely supervised by an adult at all times.
INSTALLATION INSTRUCTIONS / GUIDELINES READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLATION PRE-INSTALLATION PROCEDURES: please note: the manufacturer accepts a 1/4” variance. there are variations on each tub and specifications are subject to change as we improve upon our product as required. the dimensions needed for site preparation and structure buildings should be measured from the tub; Aquatic assumes no responsibility for preparatory work.
INSTALLATION INSTRUCTIONS STRUCTURAL PREPARATION: Note: The bath should remain in its shipping carton until time of installation. 1. Literature dimensions are for reference only. Installation dimensions should be taken directly from the tub. An unobstructed access panel of 16” x 16” minimum must be provided at the pump end of the whirlpool allowing sufficient clearance to make final connections and for servicing the pump and power panel.
INSTALLATION INSTRUCTIONS STRUCTURAL PREPARATION (continued): 6. Another installation option is that of a tile flange. Aquatic offers a factory installed tile flange for all rectangular and corner-unit whirlpools. 7. Install the whirlpool bath unit per the instructions provided in this manual. CAUTION: THE TILE FLANGE DOES NOT SUPPORT THE TUB! A ledger board must be provided under the bath rim as indicated in the installation instructions.
INSTALLATION INSTRUCTIONS Rough-In Measurements: MODEL Cambridge Camina Motif Canterbury Carmel Castaway Castaway Oval Chesapeake Clearwater Clearwater, Jr. Daytona Del Ray B Del Ray, Jr. Heart Key West (Short Side) Key West (Long Side) Laguna Mendocino Oxford Pagosa Motif Point Arena Point Reyes Point Reyes, Jr.
INSTALLATION INSTRUCTIONS electrical installation: WARNING: ALL ELECTRICAL CONNECTIONS SHOULD BE MADE BY A LICENSED, LOCALLY CERTIFIED ELECTRICIAN, IN ACCORDANCE WITH THE REQUIREMENTS OF THE NATIONAL ELECTRICAL CODES AND PROCEDURES.
chromatherapy LED light (optional) 4A Inline Heater Pump 4B Aquatic 11
INSTALLATION INSTRUCTIONS Optional inline maintenance heater operating instructions: Operation of the inline maintenance heater is completely automatic. The heater will help maintain the temperature of the water in the whirlpool. The heater includes the following components: THERMOSTAT: The “Smart Thermostat” requires no adjustment and will automatically maintain the water temperature at 102o F - 104o F. If the whirlpool is too warm, simply adjust by adding cold water.
INSTALLATION INSTRUCTIONS troubleshooting On/Off Timer Control for Estate Series: 1. If the On/Off Button does not turn on the pump, make sure the outlet has voltage. Unplug the On/Off Timer Control and plug in a hair dryer or other electrical device to see if the outlet is active. 2. If the new device you plugged in also does not work, call your electrician. 3. If the new device you plugged in does work, try the installation procedures again. 4.
INSTALLATION INSTRUCTIONS troubleshooting guide for chromatherapy led light: If light doesn’t turn on: 1. 2. 3. 4. Check to ensure LED light has been electrically connected and there is power to transformer. Check to ensure the air switch tube is connected to both the switch on LED transformer and button. Air tube should be checked to confirm there are no kinks. Check LED light to ensure that it is not broken or loose from socket.
INSTALLATION INSTRUCTIONS Installation Procedures for integrally skirted modelS: 1. To avoid obstructions during installation, make sure water lines, spout pipes and valve plumbing do not project into alcove. 2. Ledger Strip: Fasten a 1” x 3” (25mm x 75 mm) ledger strip along rear for alcove and along both sides in corner installations at Dimension LH. (see Diagram 7A) 3.
operation of Estate series whirlpools NOTE: DO NOT START PUMP UNTIL ALL JETS ARE SUBMERGED. WATER LEVEL SHOULD BE 2” ABOVE HIGHEST JET. BATHside CONTROL SYSTEMS: On/Off CONTROLS: The On/Off Electronic Button with Timer (Diagram 9A) is the On/Off Button for the pump/jet action for the Estate Series. • One-Speed Pump (9A) 1. Make sure whirlpool has enough water in it to submerge the highest jets by about 2 inches of water. 2. Push the On/Off Button once to turn the pump on.
operation of Estate series whirlpoolS jet operations: All Estate Series jets are removable, and can simply be put into the dishwasher for easy cleaning. (Note: use top rack and remove before drying cycle.) Estate Series Whirlpool Jets The Estate Series combines Full-Size Pressure-Flo Hydrotherapy Jets, Aquatic Rotary Massage Jets and StressEaz Neck and Shoulder Massage Jets (most models) to provide an invigorating hydrotherapy experience.
operation of Estate series whirlpoolS jet operations (continued): Stress-Eaz Neck and Shoulder Jets (most models): The Aquatic Stress-Eaz Jet is a rotating jet that concentrates water flow on the user’s neck and shoulder areas. • To adjust pressure: 11A 1. Grasp the outer ring of the jet. 2. Turn the outer ring clockwise to increase flow, counter-clockwise to shut off. • To adjust circular pattern (see Diagrams 11A and 11B): 1.
operation of Estate series whirlpoolS jet operations (continued): Full Size Pressure-Flo Hydrotherapy Jets: All Full-Size Pressure-Flo Hydrotherapy Jets can be interchanged with the Hand Held Jet. • To adjust pressure: 1. Grasp the outer ring of the jet. 2. Turn the jet clockwise to increase flow, counter-clockwise to shut off. 12A • To adjust direction (see Diagrams 12A and 12B): 1. Using fingertip, move jet eye to desired location. • To remove jet (see Diagram 12C): 1.
whirlpool user information Please note: Whirlpool USER INFORMATION • PLEASE NOTE: The whirlpool action may cause even small amounts of bubble bath or shampoo to foam excessively. Exercise moderation in experimenting with different soap products. No servicing of this product should be done by the user. There are no user serviceable parts. All controls are located in the control recesses on the lip of the tub. These are the only controls that should be used by the consumer.
MAINTENANCE and care INITIAL CLEANING: Before tub is used, the whirlpool system should be cleaned and disinfected. Remove all debris and clean tub before putting whirlpool into service. DO NOT USE ABRASIVE CLEANERS ON THE ACRYLIC FINISH. Use a non-abrasive detergent and rinse well after cleaning. • • • • Fill the tub with HOT water to a level 2” above the highest jet. Add 2 teaspoons of low-sudsing automatic dishwashing detergent and no more than 4 ounces of household bleach to the water.
MAINTENANCE and care SURFACE SCRATCH REMOVAL: Minor scratches may be removed by polishing your tub with a non-abrasive car polish, followed by buffing. Deeper scratches can be removed by: • Sanding with wet 400 grit sandpaper. • Sanding with wet 600 grit sandpaper. • Sanding with wet micro-grit sandpaper. • Buff out using car polish. repair: The installation and service of your whirlpool bath should be performed only by a qualified service technician.
MAINTENANCE and care water quality issues (continued): Pigmented Bacteria (continued)- In any particular case, the determination of the exact species of bacteria causing the problem would require lengthy and costly laboratory testing; however, most experts believe the bacteria responsible is Serratia marcescens. These bacteria thrive on moisture, dust and phosphates, and are widely distributed in soil, food and also in animals.
MAINTENANCE and care water quality issues (continued): 3. Treatment If you have contacted your water supplier and followed its instructions and you are still having problems, you need to increase the frequency of applications of low-foaming detergent/bleach starting from bi-monthly purging down to using it every other day as required to eliminate your particular problem.
troubleshooting guide warning: Always turn off power at the main electrical service panel when servicing your whirlpool. symptoms possible problems suggested solutions Motor does not start 1) GFCI or circuit breaker in OFF position. 1) 2) Fuses blown or thermal overload open. 2) 3) Locked motor shaft. 3) 4) Motor windings burned out. 4) 5) Defective starting switch inside 5) single-phase motor. 6) Disconnected or defective wiring. 6) 7) Low voltage.
Replacement parts Order form for Estate series How To Use: 1. Find your part on the map and make note of its number & letter. 2. Using map number and letter, choose part number and select color (or finish) on parts list provided on pages 29-30. 3. Fill out the form below with the selected information. Fax or send to Aquatic. 4. Call Aquatic for parts pricing and shipping charges.
Aquatic 27 5b. 5a. 5. 16a. 16. (option) 5b. 16b. 16c. 6a. 6. 5d. 1a. 1. Pump For 3-Speed Units Only (option) 1b. 6b. 2b. 1 and 3-Speed Timer Box 2a. 2. On/Off 3-Speed Unit 6c. Switch For 1 and Timer Box 4f. 4. 3b. (option) 4a. 4e. 4b. 3a. 3. 4b. 4c. Estate Series Replacement Parts Order Map 4d.
Estate Series Replacement Parts Order Map/Overview 8. 13. (Option) 8a. 8b. 8c. 8d. 13a. 9. 9a. (Option) 10. 10a. 10b. 14. 14a./b. (Option) 11. 15. 11a. (Option) (Option) 15a. 12. 15b. (Option) 12a. (Option) 15c. (Option) 17. 15d. (Option) 9c. 14d.
Illustration No. Description Part # 1a. Full Size Directional Jet 87DIRECTXX Specify Color 1b. Full Size Directional Jet Fitting 87ASSYWH White Full Size Directional Jet Fitting 87ASSYCL Clear Rotary Massage Jet 87SWIRLXX Specify Color 2b. Rotary Massage Jet Fitting 87ASSYWH White Rotary Massage Jet Fitting 87ASSYCL Clear 2a. Specify Color/Finish/Model# 85SWIRLXX Specify Color 3b.
Estate Bath Parts List Illustration No. 30 Description Part # Specify Color/Finish/Model# 12a. (option) Geberit Cable Drive Waste & Overflow --- Specifiy Color/Model # 13a. Vinyl Tubing 8140HOSE Specify Length 14a. On/Off Air Button (Body) 8115BODY 14b. On/Off Air Button (Cap) 8115BUTTNXX Specify Color --- 14d. 1in. Plug 8421ftg --- 15a. (option) Light Transformer 8330LIGHT --- 15b.
Aquatic Limited Lifetime Warranty For Millennium, Infinity, Century, LuxeAir, and Estate Series Whirlpools, Serenity Air Baths, Serenity Studio, HotSoak Series Baths and Restoration Series Limited Warranty For Original Consumer For Household Usage WHAT PRODUCTS ARE COVERED Structures and surface finishes, pumps and blowers on the Millennium, Infinity, Century, LuxeAir, Estate, Serenity Air Baths, Serenity Studio, HotSoak, and Restoration Series.
AQUATIC Fax-On-Demand System: Toll Free (877) 618-7024 8101 E. Kaiser Blvd. • Anaheim, CA 92808 (800) 877-2005 • Fax (714) 998-5340 • www.aquaticbath.
