IMPORTANT: Read and save Quick Reference TabNe of Contents: Pages mMPORTANT: Installer: Leave Installation the homeowner. Unstrucfions with Homeowner: Keep UnstaHafion Unstrucfions for future reference. Save Installation inspector's use. Instructions [] Before you start [] EUectdcaUrequirements [] Product dimensions [] Cabinet dimensions [] Countertop ] Vent system requirements Untedor-mounted vent motor [_-[] [_-[_ Part No. 4329225/8284826 Rev.
Your safety and the safety of others are very important, We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING". These words mean: You can be killed or seriously injured if you don't immediately foltow instructions.
important: Observe aim governing codes and ordinances. it is the customer's • To contact installer. • To assure responsibimity: a quamified that installation conformance emectricam the electrical is adequate and in with National Electrical Code, ANSi/NFPA 70 = latest edition% or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 - latest edition** and all local codes and ordinances.
8=1/4" (21cm) retractable vent height -4 !9,5 mm) 3=1/4"x 10" 18,3 cmx 26.4 cm) 16" 140,6 cm) I 9" (22.9 cm) Diameter 5/_ {15.9 ram} 15" (4&6 cm} \ BLOWER MOTOR (20,8"cm) 4&6 cm EXTERIOR=MOUNTED BLOWER MOTOR 9=3/8" 123,8 cm) (10.5 cm) See cooktop manufacturer's instructions for cooktop cutout depth aed width_ Use dimensions cutout location your installation_ for veet system that applies to 17=3/16" (433 cm} all cutouts are for 3=1/4" x 10" (8.3 cmx 25.
-- 1o7/8" /4.8 cm) 1/4" 1&4 ram) A=1/2" (12,7 ram} rain, 1/2" (12,7 mm} rain, cooktop X backsplash countertop j 1/4" (&4 mm} downdraft vent 3/4"" (19.1 Htisrecommended thatthecooktop andventcutoutsbedrawnonthe countertop beforemakingany cutoutstoavoidmistakes. SeeCooktop Installation Hnstrucfions forcompHete cutoutdimensions, Hocafion dimensions andinstallation details. IMPORTANT: Countertops with a bulhosedfrontedge are not recommended for these backsplash 1/2"" (12.
Vent system installed under a concrete slab using PVC sewer pipe. 6" (15.2 cm) round Venting system must terminate the outside. to island location metal vent 6" (15.2 cm) transition Do not terminate the vent system in an attic or other enclosed area. Do not use 4" (10.2 cm) laundry= type wall caps Do not use plastic or metal foil vent. Vent work needed for installation is not supplied. Wall cap is Not provided with interior-mounted motor. Determine which venting method to use.
6" 115.2 cm) round vent over counter support system arm J mark 90 ° elbows _-6 ft. (1,8 m) --}_1 ft, (9.6 Ma×imum length m) = 35 ft. 1&9 m) 1 - wall cap 8 ft. (2.4 m) straight 2-90 ° elbows =Off, =8ft. =10ft. (0m) (2.4 m) (3m) Transition = 4.5 ft, (1.4 m) Length of 6"" (15.2 am) system = 22.5 ft, (6.9 m) Recommended fittings 3-1/4" x 10" (8.3 cmx 25,4 am) to 6" (15,2 am} = 4.5 ft. {1,4 m) 2m Attach the left side and right side overcounter support brackets to the downdraft.
bracket rear green ground for screw venting Excessive Weight Hazard Use two or more people to move and install downdraft vent. Failure to do so can result in back or other injury. d, Remove screws attaching brackets to each side of blower. Reposkion brackets on blower as shown.Then reinstall screws. e, Reinstall blower in blower box with mouth of blower pointing out open side of blower box. Secure blower to blower box wkh 6 Phillips-head screws.
5 mConnectvent systemto blower.Ventsystemmustendwith a wall or roof cap. Useducttape to sealail joints. Installcooktopaccording to manufacturer'sinstructions. Checkthat rearof cooktopoverlaps edgeof retractabledowndraftvent by 3/8"(9.5mm). To get the most efficient use from your new retractable downdra# vent, read the Use and Care information section on page 12. Keep InstMlation instructions and Use and Care information close by for easy reference.
Recommended fittings standard .!support leg cabinet floor. AUign top of bgs with pencil marks on face of downdraft vent.Tighten screws in Uegs. ,, Attach 10" (25.4 cm) round 90° elbow = 5 ft., (1,5 m) l 45° elbow = £5 ft_ (&8 m) 4m Attach support Uegs to side of downdraft vent with two screw's in each Ueg. Do Not tighten screws. Excessive m Put on gloves and safety glasses.
microswitehes IOta behind filters. insert retractable downdraft vent into countertop cutout.Two people are recommended to support the weight of the downdraft vent during lifting. Position downdraft vent so it is centered in cutout and parallel to edge of cutout, Check that downdraft vent is vertical.Then attach lower support legs to cabinet floor wkh screws, vent box knockout ...
Theretractabbdowndraftventsystemis designed to removesmoke,cookingvaporsandodorsfromthecooktoparea. Forthebestresuks,theventshouldbeoperatingbeforecookingisstarted.If youuselargeor tall utensils,placethem onthelargerearebmentor burnersurface.A higherheatsettingthannormallyusedmaybeneededwhenthe down@aft ventis operating.
if retractable downdraft vent does not operate after clean filters have been reinstalled: Push the fiker in as far as it w,iH go. When the filter is removed, the microswitch behind the filter is inactivated.This safety feature stops the bUower and raising mechanism until the filter is propedy reinstalled. rnieroswitehes behind Note: Instructions with each kit.
Identifythe brandof your vent systemand,as appropriate,callthe KitchenAidCustomer InteractionCentertoll-freeat 1-800-422-1230 or call theWhirlpoolCustomerInteractionCentertoll=free at 1-800-253-1301. Ourconsultantsareavailableto assist you. When calling: Please know the purchase date, and the complete model and serial number of your appliance This information w,ill help us better respond to your request.
