Use and Care Manual
Table Of Contents
- MICROWAVE OVEN SAFETY
- Microwave Oven Safety
- Internet Connectivity Guide for Connected Appliances Only
- FCC Caution
- MICROWAVE OVEN MAINTENANCE AND CARE
- General Cleaning
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Product Dimensions
- Installation Dimensions
- Electrical Requirements
- INSTALLATION
- Prepare Microwave Oven Hood Combination
- Installation Types
- Find the Cardboard Plate
- Find the Wall Stud(s)
- Find the Flush Point
- Mark Upper Cabinet
- Mark Rear Wall
- Drill holes in Upper Cabinet
- Drill holes in Rear Wall
- Attach Mounting Plate to Wall
- Rotate Blower Motor
- Install Damper Assembly
- Install the Microwave Oven
- Complete Installation
- VENTING DESIGN SPECIFICATIONS
- Venting Design Specifications
- SEGURIDAD DEL HORNO MICROONDAS
- Seguridad del Horno Microondas
- Guía de Conectividad a Internet solo para Electrodomésticos Conectados
- Precaución de FCC
- MANTENIMIENTO Y CUIDADO DEL HORNO MICROONDAS
- Limpieza General
- INSTRUCCIONES DE INSTALACIÓN
- REQUISITOS
- Herramientas y Piezas
- Requisitos de Ubicación
- Dimensiones del producto
- Dimensiones de Instalación
- Requisitos Eléctricos
- INSTALACIÓN
- Preparar la combinación de horno de microondas y campana
- Tipos de Instalación
- Encontrar plantilla de cartón
- Encontrar las vigas de pared
- Encontrar el Punto al Ras
- Marcar Gabinete Superior
- Marque la Pared Posterior
- Taladrar los orificios en el Gabinete Superior
- Taladre orificios en la Pared Posterior
- Fije la Placa de Montaje a la Pared
- Gire el Motor del Soplador
- Instale el Conjunto de la Compuerta
- Instalación del horno de microondas
- Complete la Instalación
- ESPECIFICACIONES PARA EL DISEÑO DE LA VENTILACIÓN
- Especificaciones para el Diseño de la Ventilación
19
Wall Stud at One End Hole (Figure 3 in Find the
Wall Stud(s) section)
1. With the support tabs of the mounting plate facing forward,
insert a 3/16-24 x 3" round-head bolt through the end hole that
fits over the 5/8" (16 mm) hole drilled in step 3 of “Installation
for Wall Stud at One End Hole” in the “Drill Holes in Rear Wall”
section.
2. Start a toggle nut on the bolt from the back of the mounting
plate. Leave enough space for the toggle nut to go through the
wall and to open.
3. Position mounting plate on the wall.
4. Push the bolt with toggle nut through the drywall, and finger
tighten the bolt to make sure toggle nut has opened against
drywall.
5. Insert a lag screw into the remaining end hole.
6. If installing on a second wall stud, insert a lag screw into the
other hole drilled in Step 2 of “Installation for Wall Stud at One
End Hole” in the “Drill Holes in Rear Wall” section.
7. Check alignment of mounting plate, making sure it is level.
8. Securely tighten the lag screw(s) and bolt.
Rotate Blower Motor
This section include wall and roof venting installation, both venting
installation need rotate blower motor, select one ventilation type
before install the microwave oven. And follow the propriated
instruction to rotate the blower motor. If for recirculation
installation, no need to rotate the blower motor, this section can be
skip.
Rotate Blower Motor for Wall Venting Installation
1. Remove screws attaching damper plate to back of microwave
oven, set the screws aside.
A
B
A. Damper plate
B. Screw
2. Turn and hold the damper plate vertically as shown.
A
A. Damper plate
3. Remove 2 blower screws attaching blower motor to the
microwave oven, and set aside.
A
A. Blower screws
4. Disconnect the blower motor wire from the connector.
A
B
A. Blower motor wire
B. Connector
5. Lift blower motor out of microwave oven, and set aside.
A
A. Blower motor