Use and Care Manual
Table Of Contents
- MICROWAVE OVEN SAFETY
- Microwave Oven Safety
- Internet Connectivity Guide for Connected Appliances Only
- FCC Caution
- MICROWAVE OVEN MAINTENANCE AND CARE
- General Cleaning
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Product Dimensions
- Installation Dimensions
- Electrical Requirements
- INSTALLATION
- Prepare Microwave Oven Hood Combination
- Installation Types
- Find the Cardboard Plate
- Find the Wall Stud(s)
- Find the Flush Point
- Mark Upper Cabinet
- Mark Rear Wall
- Drill holes in Upper Cabinet
- Drill holes in Rear Wall
- Attach Mounting Plate to Wall
- Rotate Blower Motor
- Install Damper Assembly
- Install the Microwave Oven
- Complete Installation
- VENTING DESIGN SPECIFICATIONS
- Venting Design Specifications
- SEGURIDAD DEL HORNO MICROONDAS
- Seguridad del Horno Microondas
- Guía de Conectividad a Internet solo para Electrodomésticos Conectados
- Precaución de FCC
- MANTENIMIENTO Y CUIDADO DEL HORNO MICROONDAS
- Limpieza General
- INSTRUCCIONES DE INSTALACIÓN
- REQUISITOS
- Herramientas y Piezas
- Requisitos de Ubicación
- Dimensiones del producto
- Dimensiones de Instalación
- Requisitos Eléctricos
- INSTALACIÓN
- Preparar la combinación de horno de microondas y campana
- Tipos de Instalación
- Encontrar plantilla de cartón
- Encontrar las vigas de pared
- Encontrar el Punto al Ras
- Marcar Gabinete Superior
- Marque la Pared Posterior
- Taladrar los orificios en el Gabinete Superior
- Taladre orificios en la Pared Posterior
- Fije la Placa de Montaje a la Pared
- Gire el Motor del Soplador
- Instale el Conjunto de la Compuerta
- Instalación del horno de microondas
- Complete la Instalación
- ESPECIFICACIONES PARA EL DISEÑO DE LA VENTILACIÓN
- Especificaciones para el Diseño de la Ventilación
21
13. Secure damper plate with 2 screws removed in Step 1.
A
B
A. Damper plate
B. Screw
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
14. Plug in the microwave oven. Check if the vent fan runs with
abnormal sounds, go back through the steps to see which
step was skipped.
Rotate Blower Motor for Roof Venting Installation
1. Repeat Steps 1 to 5 from “Wall Venting Installation Only.”
2. Using diagonal wire cutting pliers, gently snip out the
rectangular vent covers on the damper plate at the
perforations.
B
A
A. Rectangular vent covers
B. Diagonal wire cutting pliers
3. Lower blower motor back into microwave oven. Exhaust ports
face the top of microwave oven.
A
A. Exhaust port
IMPORTANT: If blower motor is not positioned with flat side
facing the back of the microwave oven (as shown),
performance will be poor.
4. Reconnect the blower motor wire into the connector.
5. Reattach the 2 blower screws into the recessed holes in the
back of the microwave.
6. Check to make sure the 2 screws are secured properly in the
blower motor screw holes, so that the motor cannot move.
7. Return the damper plate to its original horizontal position.
A
A. Damper plate
8. Secure damper plate with screw removed in Step 1.
A
B
A. Damper plate
B. Screw
9. Repeat Step 14 from “Wall Venting Installation Only.”