Use and Care Manual
Table Of Contents
- MICROWAVE OVEN SAFETY
- Microwave Oven Safety
- Internet Connectivity Guide for Connected Appliances Only
- FCC Caution
- MICROWAVE OVEN MAINTENANCE AND CARE
- General Cleaning
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Product Dimensions
- Installation Dimensions
- Electrical Requirements
- INSTALLATION
- Prepare Microwave Oven Hood Combination
- Installation Types
- Find the Cardboard Plate
- Find the Wall Stud(s)
- Find the Flush Point
- Mark Upper Cabinet
- Mark Rear Wall
- Drill holes in Upper Cabinet
- Drill holes in Rear Wall
- Attach Mounting Plate to Wall
- Rotate Blower Motor
- Install Damper Assembly
- Install the Microwave Oven
- Complete Installation
- VENTING DESIGN SPECIFICATIONS
- Venting Design Specifications
- SEGURIDAD DEL HORNO MICROONDAS
- Seguridad del Horno Microondas
- Guía de Conectividad a Internet solo para Electrodomésticos Conectados
- Precaución de FCC
- MANTENIMIENTO Y CUIDADO DEL HORNO MICROONDAS
- Limpieza General
- INSTRUCCIONES DE INSTALACIÓN
- REQUISITOS
- Herramientas y Piezas
- Requisitos de Ubicación
- Dimensiones del producto
- Dimensiones de Instalación
- Requisitos Eléctricos
- INSTALACIÓN
- Preparar la combinación de horno de microondas y campana
- Tipos de Instalación
- Encontrar plantilla de cartón
- Encontrar las vigas de pared
- Encontrar el Punto al Ras
- Marcar Gabinete Superior
- Marque la Pared Posterior
- Taladrar los orificios en el Gabinete Superior
- Taladre orificios en la Pared Posterior
- Fije la Placa de Montaje a la Pared
- Gire el Motor del Soplador
- Instale el Conjunto de la Compuerta
- Instalación del horno de microondas
- Complete la Instalación
- ESPECIFICACIONES PARA EL DISEÑO DE LA VENTILACIÓN
- Especificaciones para el Diseño de la Ventilación
24
8. If for roof venting and wall venting, uninstall the charcoal filter
before use, by following below steps.
To uninstall the charcoal filter:
a. Disconnect power.
b. Push the finger grips back and then pull down the grease
filter from the bottom plate. Set aside the grease filter.
Refer to the illustration 1 for more details.
c. Pull the four hooks out to remove the charcoal filter from
bottom plate. Refer to the illustration 2 for more details.
d. Put the grease filter back into the bottom plate and the
springs toward the back. Push the finger grips back, until
the two tongues are in position, see illustration 1.
Illustration 1
A
C
B
D
A. Tongues
B. Finger Grip
C. Grease Filter
D. Spring
Illustration 2
B
A
C
D
A. Holes
B. Hooks
C. Charcoal Filter
D. Bottom Plate
The installation is now complete.
Save Installation Instructions for future use.
A
A. The height from the highest point of the stove to the
bottom of the microwave oven.
Minimum Recommendation
12
1
/
8
" (30.8 cm) 18
1
/
8
" (46 cm)
A
BC
D
A. Cabinet
B. Microwave oven
C. Wall or back of the cabinet
D. 1/2"-3/4" (1.3-1.9 cm)
VENTING DESIGN
SPECIFICATIONS
Venting Design Specifications
This section is intended for architectural designer and
builder/contractor reference only.
NOTES:
� Vent materials needed for installation are not provided with
microwave hood combination.
� We do not recommend using a flexible metal vent.
� To avoid possible product damage, be sure to vent air outside,
unless using recirculation installation. Do not vent exhaust air
into concealed spaces, such as spaces within walls or ceilings,
attics, crawl spaces or garages.
For optimal venting installation, we recommend:
� Using roof or wall caps that have backdraft dampers.
� Using a rigid metal vent.
� Using the most direct route by minimizing the length of the vent
and number of elbows to provide efficient performance.
� Using uniformly sized vents.
� Using duct tape to seal all joints in the vent system.
� Using caulking compound to seal exterior wall or roof opening
around cap.
� Not installing 2 elbows together, for optimal hood performance.
If venting through the wall, be sure that there is proper clearance
within the wall for the damper to open fully.