AUTOMATIC WASHER Design 2000” z;wE,Capacity LA5550XP
II Parts and features L!4UNDRY INFl / LOAD SIZE SELE TEMPERATURE .EACH SER MODEL AND SERIAL NUMBER PLATE (not shown) - -AGITATOR LINT FILTER (not shown] - BASKET -TUB Remove the Consumer Buy Guide label. It will be easier to remove before the washer is used. You should wipe out the basket with a damp cloth before using to remove dust from storing or shipping. Copy your Model and Serial Numbers When you need service or call with a question, have this information ready: I.
Your re msibilities Read this “Use and Care Guide” and your “Laundry Guide” carefully for important use and safety information. You are personally responsible for making sure that your washer.. l is installed by a qualifiedinstaller. l is properly installed and leveled on a floor that can support the weight.* l is connected to the right kind of outlet, electric supply, water supply and drain.* l is properly grounded.+ l is used only for jobs normally expected of home automatic washers.
Starting your washer Before starting Select 1. LOAD your washer: a SIZE 1 Measure and add detergent 2 Place sorted load in washer 3 Start washer. 2. Turn the knob to point at a setting that describes the size of load you want to wash. . Set the knob anywhere on or between EX SMALL (a few items) and LARGE (a full load). l Select WATER TEMPERATURES .
3. Start the washer A. Push in the Control Knob and turn it to the right. It must be pushed in and turned only clockwise. B. Stop on a mark in the cycle you want. The marks represent minutes of wash time. The drawing shows 10 minutes of agitation in the REGULAR LIGHT Cycle. C. Start the wusher by pulling out the Control Knob. The washer will fill to the level you set with wash water of the selected temperature. After filling, the washer will agitate for the selected wash time. D.
What happens in each cycle* Each cycle has different kinds of fabrics. agitation and spin speeds designed for different When the Cycle Control Knob is set to a mark and pulled out, the washer fills before agitation and timing starts. After agitation starts, the knob turns clockwise until it points to OFF and the cycle ends. REGULAR HEAVY Cycle A cycle for sturdily constructed fabrics that are heavily soiled.
NOTE: You may hear the sound of water spraying some cycles.
PERMANENT PRESS LIGHT Cycle A cycle designed for moderately to lightly soiled permanent press and synthetic items. The cool down rinse helps keep wrinkles from setting into these items.
Other operating For a rinse instructions and spin You may need an extra rinse and spin for heavily soiled loads which need more detergent. (Extra deteraent can require an extra rinse.) l PGsh Control Knob in. l Turn clockwise to any .on the dial. See above drawing. l Pull Control Knob out. l The washer will fill to selected level; agitate 2 minutes; drain and spin. For agitation and spin speeds Cleaning the lint filter Clean filter after every load for best filtering results.
I II Liquid bleach dispenser Always measure bleach. Do not guess. Never use more than 1 cup (250 ml) for a full load. Use less with lower water level settings. Follow directions on bottle for safe use. Use a cup with a pouring spout to avoid spilling. 1. Load the washer first. 2. Pour measured bleach carefully into dispenser. DO NOT let bleach splash, drip or run down into the washer basket. Undiluted bleach will damage any fabric it touches. 3. Start the washer.
I II Caring for your washer WHEN NOT WASHING, keep both water faucets turned off. This takes the pressure off the water inlet valve and hoses. AFTER WASHING, use a soft dry cloth to wipe the outside and inside dry. Leave the lid up until the basket is dry. Wipe up spills right away. Spills can dull or damage the finish. REMOVE SHARP OBJECTS such as pins, buckles, etc., from clothes before washing. Close metal zippers. SHARP OR HEAVY OBJECTS should never be put on or in the washer.
Winterizing I Because some water stays in the washer, freezing can cause a lot of damage. If your washer is stored or moved during the cold weather., 1. Shut off both water faucets. Disconnect and drain water inlet hoses. 2. Put a quart of automobile-type antifreeze in the basket. 3. Set the washer for a DRAIN and SPIN [see page 10). Let it run for about 30 seconds to mix the antifreeze and water. ON To use the washer again.. . 1. Flush water pipes and hoses. 2. Connect hoses to the washer. 3.
If you need service or assistance, we suggest you follow these four steps: 1. Before calling for assistance.. Performance problems often result from little things you can find and fix yourself without tools of any kind. .
2. If you need assistance*. .. Call Whirlpool COOL-LINE@ service assistance telephone number. Dial free from: Continental U.S. . (BOO] 253-1301 Michigan . . . . . . . (800) 632-2243 Alaska & Hawaii (800) 253-1121 and talk with one of ourtrained Consultants. The Consultant can instruct you in how to obtain satisfactory operation from your appliance or, If service is necessary, recommend a qualified service company in your area. 3. If you need service*. . .
Home I Appliances Making your world a llttle easier. Part No. 387420 01985 Whirlpool Corporation Printed in U.S.A.
