Use&CareGuide Cycle control knob ‘emperature I selector Cycle I signal Start button Lint screen Model and serial Electronic DRY-MISEW sensor SUPERCAPACITY AUTOMATICDRYERS LE9500XT LG95OlXT LE9520XT LG952lXT
Contents Page Important Safety Instructions. Additional safety instructions and your responsibilities Operating Instructions Starting your dryer The automatic cycles . Timed drying . Using fluff air Using TUMBLE PRESS@ Using damp dry End-of-cycle signal Lint signal.. . Additional Dryer Features Gentle heat system FINISH GUARD@ setting Caring For Your Dryer Cleaning the lint screen Cleaning the dryer interior Lint removal If You Need Service Or Assistance. Whirlpool Automatic Dryer Warranty..................
ImportantSafetyInstructions l l l l l l l Read all instructions before using the dryer. NEVER dry items cleaned, washed, soaked in or spotted with wax, paint, gasoline or flammable fluids in the dryer. The fumes can create a FIRE HAZARD or EXPLOSION. ALWAYS hand launder and air dry fabrics containing these materials. NEVER allow children to operate, play with or crawl inside the dryer. Close supervision of children is necessary when the dryer is used near children.
i I OperatingInstructions The drawings in this book may vary slightly from your dryer model. They are designed to show the different features of all the models covered by this book. Startingyour dryer Be sure to refer to the chart below and the Dryer Guide for proper sorting, loading and control setting information before starting it.
II 1. Select a cycle by turning the Cycle Control Knob either way. Stop when the indicator on the knob’s outer ring points to the cycle and setting you want. See pages 6-8 for further cycle information. 2. Press a temperature selection which matches the type of fabric being dried. The indicator will appear over the temperature selection you have chosen. 3. Push the Start Button the dryer. to start 4. To stop and restart the dryer: Open the door or turn the Cycle Control Knob to OFF to stop the dryer.
Operating Continued Instructions Theautomaticcycles The automatic cycles allow you to select the degree of dryness you prefer for the clothes being dried. The electronic DRY-MISER@ control is an electronic sensor that determines the amount of moisture in the clothes. The dryer automatically shuts off when the proper dryness is reached. The Cycle Control Knob will not move until the clothes load is almost dry, or the Cool-Down portion of the cycle has been reached.
TIMEDDRYING UsinaFLUFFAIR Fire Hazard Do not dry plastic or rubber items with heat. Use FLUFF AIR setting, or line dry. Failure to do so could result in fire or damaged items. The dryer does not heat when the Cycle Control Knob is set in FLUFF AIR. This cycle can be used to fluff or air dry bedding, plastic tablecloths, foam rubber pillows, stuffed toys, sneakers, etc. 1. Turn the Cycle Control Knob to the number of minutes you want in FLUFF AIR. 2. Push the Start Button.
Operating Continued Instructions UsingDAMPDRY Use this setting to dry damp items that do not require an entire drying cycle, or to dry items to damp level. (Two examples are heavy cottons, such as jeans, which you do not want to become stiff, or cotton clothes which are easier to press when damp.) 1. Set the Cycle Control Knob on DAMP DRY in the TIMED DRYING cycle. 2. Push the Start Button. The dryer tumbles the load with heat for 25 minutes, then without heat for 5 minutes.
AdditionalDryerFeatures GentleHeatsystem FINISHGUARD@ setting The dryer automatically reduces the heat settings in HEAVY HIGH and PERM’T PRESS, During the last few minutes of each of these temperature settings, the dryer temperature gradually reduces to a lower heat setting. This helps prevent overdrying. When you are unable to remove a load from the dryer as soon as it stops, wrinkles can form. FINISH GUARD tumbles the load, without heat, every 5 minutes for up to 40 minutes.
CaringForYourDryer Cleaningthe lint screen The lint screen is located under a lid on top of the dryer. Clean it before load. A screen blocked by lint can increase drying time. each 1. Open the lid and pull the lint screen straight out. 2. Roll lint off the screen with your fingers. Do not rinse or wash the screen. Wet lint is hard to remove. 3. Push the lint screen firmly back into place and close the lid.
Powdered laundry detergent Make a paste with detergent and very warm water. Apply paste to a soft cloth and scrub area until all excess dye is removed. Wipe thoroughly with a damp cloth. Tumble a load of rags to dry. -ORLiquid household cleaner Apply to stained area. Rub with a cloth until all excess dye is removed. Tumble a load of rags to dry. To clean dryer exterior, wipe with a soft, damp cloth.
II If YouNeedServiceOrAssistance We suggestyou follow thesesteps: 1. Before calling for assistance... Performance problems often result from little things you can find and fix yourself without tools of any kind.
4. If you need FSP’ replacement parts’... FSP is a registered trademark of Whirlpool Corporation for quality parts. Look for this symbol of quality whenever you need a replacement part for your Whirlpool appliance. FSP replacement parts will fit right and work right, because they are made to the same exacting specifications used to build every new Whirlpool appliance. To locate FSP replacement parts in your area, refer to Step 3 or call the Whirlpool COOL-LINE set-vice assistance number in Step 2. 5.
I I’ Notes 14
Notes -.
I I I’ Whirlpool’Automatic DryerWarranty DROO LENGTH OF WARRANTY FULL ONE-YEAR WARRANTY From Date of Purchase WHIRLPOOL 1 WHIRLPOOL WILL PAY FOR FSP@ replacement parts and repair labor to correct defects in materials or workmanship. Service must be provided by an authorized WhirlpoolSM service company. WILL NOT PAY FOR A. Service calls to: 1. Correct the installation of the dryer. 2. Instruct you how to use the dryer. 3. Replace house fuses or correct house wiring or plumbing. 4.
