Use& CareGuide Cycte control knob I Temperature selector Start bution LARGECAPACITYAUTOMATICDRYERS LE5320XT LE5530XS LE5600XS LE5650XM LE5700XS LE5705XP LE6055XS LG5321XT LG5531XS LG5601XS LG5651XM LG57OlXS LG5706XP LG6056XS
Contents lmp4xtant Safety Instructha Page Additional safety instructions and your responsibilities.. .............. .3 Operatlng Instructlons Starting your dryer.. ....................... The regular cydes ......................... The permanent press cycle ........... Using fluff air ................................. Using TUMBLE PRESS@. .............. Using damp dry ............................. Lint signal ...................................... .4 .6 .7 .7 6 .9 .
Important Safety Instructions To reduce the risk of fire, electrlcal shock, or Injury to persons when using your dryer, follow bask precautkns, lncludlng the following: l l l l l l l Read all lnsttuctkns before using the dryer. NEVER dry items cleaned, washed, soaked in or spotted with wax, paint, gasoline or flammable fluids in the dryer. The fumes can create a FIRE HAZARD or EXPLOSION. ALWAYS hand launder and air dry fabrics containing these materials.
Operating instructions . Starting your dryer Be sure to refer to the chart below and the Dryer Guide for Proper sorting, bading and oontrol setting information before starting your dryer. NOTE: Do not overdry. Overdrying oan cause shrinkage, static ding, and damage some fabrics. SUGGESTED SUGGESTED TEMPERATURE CYCLE TYPE OF LOAD Cottona and linam EXTRA HEAVY-Bedspraads. matkess pads. quilts HEAVYWEIGHT-Towels, bans, corduroys, work dothas MEDIUMWEIGHTSheets, pillowcases.
1. Select a cyole by turning the Cycle Control Knob either way. Stop when the indicator on the knob’s outer ring points to the cycle and time you want. See pages 6-9 for further cycle information. 2. Set the Temperature Selector on the desired temperature setting. 3. Push the Start Button to start the dryer. 4. To stop and restart the dryer: Open the door or turn the Cycle Control Knob to OFF to stop the dryer.
Operating lnstructluns Continued The regular cycles The names of the regular cycles describe the types of loads they are designed to dry. Each cyde ls followed by a 5 minute cool-down period. During the cool down, the bad tumbles without heat. This helps make the bad easier to handle. Use EX HEAVY to dry items such as bedspreads, mattress pads and quilts. Use HEAVY to dry items such as towels, jeans, corduroys and work clothes. Use MED to dry items such as sheets, pillowcases, cotton underwear and diapers.
T$;ERMANENT PRESS The PERMANENT PRESS cycle helps provide the special care that psrmanent press and synthetic fabrfcs need. The cyde consists of a timed period of heated drying and a 10 minute cooldown period. During the cool down, the bad tumbles without heat. This helps keep wrinkles from setting and makes the bad easier to handle. NOTE: To help reduce wrinkling, remove the bad from the dryer as soon as tumbling stops. This is important for permanent press, knits and synthetic fabrii.
Operating Instnrctbna Continued UsingTUMBLEPREW The TUMBLE PRESS setting removes wrinkles from cbthing that has been packed in a suitcase or closet, and from items not removed from the dryer at the end of a cycle. 1. Set the Cycle Gontrol Knob on TUMBLE PRESS. 2. Set the Temperature Selector on PERM’T PRESS HEAVY HIGH. 3. Push the Start Button. For best results, put only a few items at a time in this cycle. As soon as the dryer stops, put the items on hangers or fold them.
UsingUAMPDRY Use this setting to dry damp items that do not require an entire drying cycle, or to dry items to damp level. (Two examples are heavy cottons, such as jeans, which you do not want to become stiff, or cotton clothes which are easier to press when damp.) 1. Set the Cycle Control Knob on DAMP DRY. 2. Push the Start Button. For all modeb (except LE565OXy LG5651XM LE!5705XP, LGs706XP): The bad will tumble in heated air for 20 minutes.
Caring For Your Dryer Product and Fabric Damage Hazard Do not run the dryer with the llnt ecreen loose, damaged, blocked or mfeslng. Dolng 80 can ceuse overheatlng and damage to both the dryer and fabrics. Cleaningthe lint screen The lint screen is located under a lid on top of the dryer. Clean lt before each load. A screen blocked by lint can increase drying time. 1. Open the lii and pull the lint screen straight out. 2. Roll lint off the screen with your fingers.
Cleaningthe dryer Electrlcal Shock and Personal Injury Hazard l Turn off the electrical power before cteanlng the Interior. l Make sure the dryer ls cool. Failure to do so could result ln electrical shock or Injury. Fire Hazsrd l Use non-flammable cleaner. Failure to do so could result In an explosion. Garments which contain unstable dyes, such as denim blue jeans or brightly cobred cotton items, may discolor the dryer interior.
Carlng For Your Dryer Continued Lint removal Lint can gather inside the dryer and be a fuel for fire. ft is recommended the lint ba removed every 2 to 3 years, or more often, depending on dryer usage. Cleaning shoukl be done by a qualified person. lf you have any questions, please call our Consumer Assktance Center at I-800-2!53-1301. Electrical Bhock and Personal injury Hazard l Unplug the power suppty cord or turn off the electrlcol power before removlng dryer panels. l Make sure the dryer Is cool.
llomove-0 bdorm opmlng top Wire dipbold8 door l wlIoh wtrcm tfyokuchyefk’&sandhamaWIfront pfld#-fNlltpcuwl~kl~ 1. Unplug the power supply cord or turn off the electrbal power. 2. Cpen lint screen lb. Remove two screws in lint screen area. 3. Open top by pulling forward and up at each front corner (see view A). Rest raised top against wall behind dryer (top is hinged at rear). 4. Remove two internal screws from front panel flanges (near top front comers).
If You Need Service Or Assistance We suggestyou follow these steps: 1. Before calling for assistance “. Performance problems often result from little things you can find and fix yoursefl without tools of any kind.
.. 4. If you need FSP replacement parts*... FSP is a registered trademark of Whirlpool Corporation for quality parts. Look for this symbol of quality whenever you need a replacement part for your Whirlpool appliance. FSP replacement parts will fit right and work right, because they are made to the same exading specifiitions used to buikf every new Whirlpool appliance. To locate FSP replacement parts in your area, refer to Step 3 or call the Whirlpool Consumer Assistance Center number in Step 2. 5.
WHIRLPOOL’= Automatic Dryer Warranty LENGTH OF WARRANTY FULL ONE-YEAR WARRANTY From Date of Purchase DROOl WHIRLPOOL WlLL PAY FOR FSP replacement parts and repair labor to correct defects in materials or workmanship. Service must be provided by an authorized WhirlpoolSM service company. WHIRLPOOL WILL NOT PAY FOR A. Service calls to: 1. Correct the installation of the dryer. 2. Instruct you how to use the dryer. 3. Replace house fuses or correct house wiring or plumbing. 4. Replace light bulbs. B.