Xfl 01 4a Use&CareGuide Cycle control knob Temperature selector I Start button Lint screen Model and serial DRY-MISER@ sensor Loading door SUPERCAPACITYAUTDMATICDRYERS LE6098XT LE6880XT LE7080XT LG6099XT LG688lXT LG708lXl
Contents Important Safety Instructions .................. Additional safety instructions and your responsibilities ..... Operating Instructions Starting your dryer. ........... The automatic cycles ......... Timed drying ................ Using fluff air ................ Using TUMBLE PRESS@ ...... Using damp dry .............. End-of-cycle signal ........... Lint signal ................... Additional Dryer Features Electronic DRY-MISER@ control Gentle heat system ........... FINISH GUARD@ setting ......
ImportantSafetyInstructions l l l l l l l l You are responsible for making Read all instructions before using the dryer. sure that your dryer is installed, repaired and parts replaced by a NEVER dry items cleaned, aualified oerson. washed. soaked in or SDOtkd with wax, pa/m, gasoline or flammable l Use only fabric softeners specififluids in the dryer. The fumes can cally labeled as not being harmful create a FIRE HAZARD or to the dryer. EXPLOSION.
OperatingInstructions The drawings in this book may vary slightly from your dryer model. They are designed to show the different features of all the models covered by this book. Startingyour dryer Be sure to refer to the chart below and the Dryer Guide for proper sorting, loading and control setting information before starting it.
1. Select a cycle by turning the Cycle Control Knob either way to point to the cycle and setting you want. See pages 6-6 for further cycle information. 2. Set the Temperature Selector on or between any desired temperature settings. 3. Push the Start Button the dryer. to start 4. To stop and restart the dryer: Open the door or turn the Cycle Control Knob to OFF to stop the dryer. l Close the door, select a cycle (if necessary) and push the Stan Button to restart the dryer.
Operating Continued Instructions Theautomaticcycles The automatic cycles allow you to select the degree of dryness you prefer for the clothes being dried. The electronic DRY-MISER@ control is an electronic sensor that determines the amount of moisture in the clothes. The dryer automatically shuts off when the proper dryness is reached. The Cycle Control Knob will not move until the clothes load is almost dry, or the Cool-Down portion of the cycle has been reached.
TIMEDDRYING Use the TIMED DRYING cycle for any load you want to dry by time. . Turn the Cycle Control Knob to the number of minutes you want from 10 to 70. The last 5 minutes of this cycle are without heat to help make the load easier to handle. Drying plastic or rubber items 1 ~;;lw~;~~~~~the items 1 UsingFLUFFAIR The dryer does not heat when the Cycle Control Knob is set in FLUFF AIR.
Operating Continued Instructions UsingDAMPDRY Use this setting to dry damp items or to leave wet items damp. (Heavy cottons, for example, are easier to press when damp and do not become stiff.) 1. Set the Cycle Control Knob on DAMP DRY in the TIMED DRYING cycle. 2. Push the Start Button. The dryer tumbles the load with heat for 25 minutes, then without heat for 5 minutes. ‘5 Y3’ ,\- End-of-cyclesignal The dryer sounds a signal to let you know when the cycle is finished.
AdditionalDryerFeatures ElectronicDRY-MISER” control The electronic DRY-MISER control is an electronic sensor that determines the amount of moisture in the clothes. The dryer automatically shuts off when the proper dryness is reached. GentleHeatSystem The dryer automatically reduces the heat settings in HEAVY HIGH and PERM’T PRESS MED. During the last few minutes of each of these temperature settings the dryer temperature gradually reduces to a lower heat setting. This helps prevent overdrying.
CaringForYourDryer Cleaningthe lint screen The lint screen is located under a lid on top of the dryer, Clean it before load. A screen blocked by lint can increase drying time. each Do not run the dryer with the lint screen loose, damaged, blocked or missing. Doing so can cause overheating, damage and be a FIRE HAZARD. I. Open the lid and pull the lint screen stratght out. 2. Roll lint off the screen with your fingers. Do not rinse or wash the screen. Wet lint is hard to remove. 3.
Powdered laundry detergent Make a paste with detergent and very warm water. Apply paste to a soft cloth and scrub area until all excess dye is removed. Wipe thoroughly with a damp cloth. Tumble a load of rags to dry. -ORLiquid household cleaner Apply to stained area. Rub with a cloth until all excess dye is removed. Tumble a load of rags to dry. To clean dryer exterior, wipe with a soft, damp cloth.
If YouNeedServiceOrAssistance Wesuggestyou follow thesesteps: 1. Before calling for assistance... Performance problems often result from little things you can find and fix yourself without tools of any kind. If your dryer does not run: Is the power supply plugged into a live circuit with the proper voltage? l Is the door closed tightly? l Did you push the Stan Button? l Have you checked your home’s main fuses or circuit breaker box? l If your dryer does not heat: The FLUFF AIR setting is without heat.
4. If you need FSP” replacement parts’... FSP is a registered trademark of Whirlpool Corporation for quality parts. Look for this symbol of quality whenever you need a replacement part for your Whirlpool appliance. FSP replacement parts will fit right and work right, because they are made to the same exacting specifications used to build every new Whirlpool appliance. To locate FSP replacement parts in your area, refer to Step 3 or call the Whirlpool COOL-LINE service assistance number in Step 2. 5.
Notes 14
Notes 15
Whirlpool@Automatic DryerWarranty DUO01 LENGTH OF WARRANTY FULL ONE-YEAR WARRANTY From Date of Purchase WHIRLPOOL r---- WHIRLPOOL 1 WILL PAY FOR FSP@ replacement parts and repair labor to correct defects in materials or workmanship. Service must be provided by an authorized WhirlpoolSM service company. WILL NOT PAY FOR A. Service calls to: 1. Correct the installation of the dryer. 2. Instruct you how to use the dryer. 3. Replace house fuses or correct house wiring or plumbing. 4.
