&Through 1Washer tInstallation & iOperatingGuide ! Model No.
If you have any problems or questions regarding your See-Through Washer, please contact your Whirlpool Account Manager or Field Marketing Representative or call toll-free: l-800-253-1301
I Unit Not for Resale! Whir/pool Corporationhas built this demonstrationunit to showyour customershow Whir/poolAutomatic Washerscreaterollover at all agitation speedswith the newXtra Roll ActionTM Agitator.
Installation Instructions Your‘demo model must be installed using the following manual fill method. Placethe Unit into position on the sales floor, preferably on an end cap next to a Whirlpool 34peed washer. With pliers, remove the yellow plug at the base of the washer in the back.The plug must be completely removed for the self-levelinglegs to be released. Insert leveling legs into correct holes at each front corner of washer until nuts touch washer.Do not tighten nuts until step 6.
Installation Instructions Tilt washer forward, raising back legs 1” off of floor to adjust rear self-levelinglegs.Gently lower washerto floor. Check levelnessof the washer by placing a carpenter’slevel on the top of the washer,first side to side;then front to back. 0 If washer is not level, screwthe front legs up or down to adjust and repeat step 4. Once the washer is level, use wrench to turn nuts on front legs up tightly against washer base.
Installation Instructions Verify that the drain plug is securedin the drain port as shown. Manually fill the basket (using a bucket or garden hose) with 20-23 gallons of water (A). Fill to top of gasketon basket.Set the Water Options dial to “Without Water.”(B)* *If you are running the demonstrationmodelwithout any waterat all, you must add at least I pint of waterto the basketfor proper operation. Checkregularlyfor evaporationand repeatas needed.
Installation Instructions Pushthe Timer dial in (Washeris now in OFF position) 1 With a screwdriver,turn the Drain I Agitate Switch on the back of the washerto “Agitate” Load the 200 colored chips into the machine. (SeePage1 for how to order your free demo swatches.
Installation Instructions Plug-in the unit using a 20 amp 3-pronged, electrically grounded extension cord not longer than 50 feet. Turn the lights on with the Light rocker switch on the back of the machine. Pull the timer on. Pull The unit may now be operated using the Demonstration Options listed in the Demonstration Instruction section of this manual.
To Drain Unit CilW u 1 ater may be siphoned into a drain or 25-gallon container on wheels. To change from plug to 8 drain hose,turn machine off and put option dial to “One Speed Continuous” (A). Turn the timer dial to HIGH speed(B). With a screwdriver turn the Drain /Agitate switch to “Agitate” and turn the machine on. (41 w While machine is agitating, remove plug cap and put drain hose on. Somewater may drip out or spill. Turn machine I OFF and turn Drain/Agitate switch to I DRAIN.
I Demonstration Kit & Materials 1 Hanger - for hanging this booklet on the back of the unit. 200 colored chips 8 1 Service Request Fax Form (on back page of Instruction Manual). Make Xerox copies as needed. 10 Poly-Cotton Swatches can be obtained by ordering through Whirlpool Fulfillment. (See page 1) Only use the poly-cotton skatches provided by Whirlpool Fulfillment in your demonstrations. These poly-cotton swatches have been tested to sustain many hours of agitator demonstrations.
Care for the See-ThroughWasher l l l Keep the viewing glass clean by wiping down with a soft cotton cloth. DO NOT USE PAPER TOWELS.THEY WILL SCRATCH THE SURFACE. It is important to keep the water in the dlemonstration model clean and clear for the blest visibility inside the washer. When you nlotice the water is becoming cloudy or dirty, it is time to change the water. Liimited contact with the water helps keep it cl,eaner longer.
Operating Instructions You and your customers have three demonstration options to choose from All SpeedsContinuous- preferred operation mode Set DemonstrationsOptions dial to “All SpeedsContinuous” Pull Timer on l l All SpeedsOnce - demonstrateeachmodeonce Set DemonstrationsOptions dial to”AIl SpeedsOnce” Pull Timer on (will operate until timer reachesOFF position) Pushto start or restart l l l One SpeedContinuous- demonstrateone mode on/y l l l Set DemonstrationsOptions dial to “One SpeedContinuous”
Unique Parts for Service Control Panel mh Light and Drain /Agitate Switcheson back of console Lid Assembly consisting of lid, lid cutout and lid window f h Front Panel Assembly consisting of front panel cutout and window 11
Uniq~ueParts for Service Lighting b holes Basketwith See-Through window and gasket Light Bracket Gear Case 12
Whirlpool is Responsible for the Following: l Labor and parts for repairing the unit l Furnishing demonstration materials l Hauling the unit after demonstration APPLIANCES
TO REQUEST SERVICE FAXto: FAXPH#: Note: CACPartner Team l-800-545-9093 Pleasecontacta local servicerand request servicefor the washer below SERVICE REQUEST FORWHIRLPOOL SEE-THROUGH WASHER DEALElR INFORMATION WASHER INFORMATION I Store Name: Store #: ContactPerson: Phone#: Store Address: Model #: LSR4311DQO Serial #: Descriptionof Problem: SERVICE INSTRUCTIONS Pleasecontactthe dealerlisted. Pleasearrangeto servicethe washer IMMEDIATELY. Bill Rework #R22591 for all labor and commonparts.