Installation guide

ManualsBrandsWhirlpool ManualsWasherOfficial Whirlpool home direct-drive washer

Installation Instructions

©©

save these

_iiiii_!i_:_!:;!!iiiiiiiiiiiiiiiiiiiiii_:::::iiiiiiiiiiiiiiii!iiii_iiiiii_ii_iiiiiiiiiiiiii_st__nSeo

IMPORTANT:

Installer: Leave Installation Instructions with the homeowner.

Homeowner: Keep Installation Instructions for future reference.

lave Installation Instructions for local electrical inspector's use.

Part I'40,:3_!i!iii_ii_iiiiii_iii_!i

:::::::::::::::::::::::::::::::::

Your safety and the safety of others is very important.

We have provided many important safety messagesin this manual and on

your appliance.Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to hazardsthat

can kill or hurt you and others. All safety messageswill be preceded

by the safety alert symbol and the word "DANGER"or "WARNING".

Thesewords mean:

You will be killed or seriouslyinjured if

youdon't follow inslructions.

Youcanbe killed or seriouslyinjured if

you don'l follow instructions.

All safety messageswill identify the hazard,tell you how to reduce the

chance of injury, and tell you what can happen if the instructions are not

followed.

Parts supplied'.

Open lid and remove parts from

inside washer. Check that all parts

were included.

4 flat water

hose washers

2 inlet h_

1 drain

hose

drain hose clamp

2 front leveling legs

with nuts

Tools needed:

yellow clamp

literature package

(inside washer)

pliers

_ss°rs iitility _

_ knife

adjustable wrench or

9/16" open-end

wrench

Summary of content (5 pages)

PAGE 1
Installation Instructions Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to hazardsthat can kill or hurt you and others. All safety messages will be preceded by the safety alert symbol and the word "DANGER" or "WARNING". These words mean: ©© You will be killed or seriouslyinjured if you don't follow inslructions.
PAGE 2
Locatio n of w ashe r: Check location where washer will be installed. Make sure you have everything for correct installation. Proper installation is your responsibility• Recessed area instructions Hot and cold water faucets: Should be within This washer may be installed The installation dimensions shown are the minimum spaces allowable. Additional spacing should be considered for ease of installation and servicing.
PAGE 3
Level washer. hoses to ttach inlet water valves. D Plug power supply cord into grounded outlet. washers nsert into inlet hoses. D 1_ inlet ttachhoses to water faucets. Read and then remove label. _r for drain hose connection. Power cord attached strap. is to shipping se yellow iect rigid and flexible drain hose sections. Secure drain hose to laundry tub or standpipe. Attach drain hose to drain connector. Check that drain hose is proper length.
PAGE 4
Drain hose connection'. • Wet the inside end of the drain hose with tap water. DO NOT USE ANY OTHER LUBRICANT. IMPORTANT: THIS PROCEDURE MUST BE FOLLOWED TO ASSURE PROPER I NSTALLATION. F • Squeeze ears of drain hose clamp with pliers to open and place clamp over the end of the drain hose. _drain _.._t_- _ • Open clamp and push end of drain hose onto drain connector until hose contacts ribbed stop. • Place clamp over area marked "clamp". Release clamp.
PAGE 5
Completing Installation: 8o CHECK ELECTRICAL REQUIREMENTS. BE SURE YOU HAVE CORRECT ELECTRICAL SUPPLY AND RECOMMENDED GROUND METHOD. 0• Turn on water faucets and check for leaks. Tighten couplings if there is leaking. DO NOT OVERTIGHTEN; this could cause damage to couplings. 2. Plug power supply cord into grounded outlet. 3 • Read the Use and Care Guide. Start the washer and allow it to complete the regular cycle. (Step 13) Congratulations! (Step 4) 19. Check that all parts are now installed.