KAC-43 TECHNICAL EDUCATION FAILURE CODES AND WIRING DIAGRAMS for WHIRLPOOL AND KITCHENAID SLIDE-IN & FREESTANDING GAS & ELECTRIC RANGES JOB AID 4317368
FORWARD This KitchenAid Job Aid, “Failure Codes And Wiring Diagrams For Whirlpool and KitchenAid Slide-In & Freestanding Gas & Electric Ranges,” (Part No. 4317368), provides the technician with information on diagnosing and troubleshooting slide-in and freestanding gas & electric ranges. It is to be used as a training Job Aid. For specific information on the model being serviced, refer to the “Use and Care Guide,” or “Tech Sheet” provided with the unit.
MODEL/SERIAL NUMBER LABEL AND TECH SHEET LOCATIONS Tulsa-Built Units Model/Serial Number Label Location (Behind Storage Drawer) Tech Sheet Location (On Rear Panel) Oxford-Built Units Model/Serial Number Location (On Chassis Frame) Tech Sheet Location Warming Drawer Models Only (On Chassis Under Drawer) Model/Serial Number Location (On Chassis Frame) Tech Sheet Location Storage Drawer Models Only (On Underside Of Drawer) 1
REFERENCE CHART Power Board Display Board KeyPad Component Check Page 9756993 9756997 9758315 9757663 9757662 9756531 9756534 9756535 9756591 9756595 8-10 11-13 70 70 4 4 9759563 9759561 9759561 9756547 9756548 9759566 9759564 9759565 14-17 18-21 64-65 64-65 4 5 KESA907P BL, BB, SS, WW 9757662 9759561 9759565 9756595 22-26 22-26 64-65 64-65 5 5 KGRA806P BL, BT, SS, WH 9757665 9759562 9760201 9756559 KGSA906P BL, BT, SS, WH KGRI801P BL.
CONSOLE COLORS Black Black on Stainless Meteorite Stainless Biscuit on Biscuit 4453608 White 4453601 6610394 6610396 6610398 6610399 6610439 6610440 6610438 6610441 6610443 6610442 8523284 8523281 8523283 9756531 9756529 9756530 9756534 9756533 9756532 6610395 6610397 9756535 9756537 9756536 9756538 9756563 9756565 9756564 9756566 9756555BL 9756555BL 9756555WH 9756556BL 9756559BL 9756555WH 9756556WH 9756559BS 9756559ES 9756560BL 9756591BL White on White 9756560ES
ERROR / FAILURE CODES (TULSA & CELAYA) 4 DIGIT DISPLAY 3 DIGIT DISPLAY F0 E0 F1 E0 E0 F1 Control will flash the HEATING LED. EEPROM communication error. F1 E1 F1 Control will flash the HEATING LED. EEPROM checksum error. F1 E2 N/A N/A UL A/D error. F1 E4 N/A N/A Model ID error. F1 E6 N/A N/A Latch signal mismatch error.
ERROR / FAILURE CODES (OXFORD) Before proceeding with any corrective action, perform the following steps to enter the Diagnostic mode. 1. To recall last failure code, if not displayed, press the Cancel key to place the range in an idle state. 2. Press the Cancel and Start keys in the following order: CANCEL, CANCEL, START. 3. Verify the error code displayed on the control by observing for longer than 1 minute.
FAILURE ERROR (Leftmost (Rightmost 2 Clock 2 Clock Digits) Digits) E0 E1 F3 Sensors E2 E4 E5 E6 E7 FAILURE ERROR MESSAGE/DESCRIPTION (Leftmost (Rightmost 2 Clock 2 Clock Digits) Digits) SUGGESTED CORRECTIVE ACTION PROCEDURE MAIN SENSOR OPEN (top oven sensor opened) MAIN SENSOR SHORT or MAIN SENSOR SHORTED (top oven sensor shorted) MEAT PROBE SHORTED BOTTOM SENSOR OPEN (bottom oven sensor open) LOWER SENSOR SHORT or BOTTOM SENSOR SHORT (bottom oven sensor shorted) WD SENSOR OPEN (warming drawer sensor o
FAILURE ERROR (Leftmost (Rightmost 2 Clock 2 Clock Digits) Digits) E0 F5 Inputs E1 E2 E4 E7 FAILURE ERROR MESSAGE/DESCRIPTION (Leftmost (Rightmost 2 Clock 2 Clock Digits) Digits) SUGGESTED CORRECTIVE ACTION PROCEDURE DOOR LATCH MSMATCH or DOOR LATCH MISMATCH (Door and latch switches do not agree.
KITCHENAID & WHIRLPOOL ELECTRONIC CONTROL SYSTEMS (BY INDIVIDUAL MODEL) KITCHENAID (TULSA-BUILT) FREESTANDING MODEL KERI201P MODEL: KERI201P Keypad Layout 1 2 3 4 5 6 7 8 BROIL BAKE BREAD PROOF KEY #2 TIMER SET/START CLOCK SET/START SELF CLEAN TIMER OFF OPTIONS KEY #9 STOP TIME COOK DURATION KEY #8 KEY #0 OVEN LIGHT KEY #6 KEY #5 KEY #3 KEY #7 KEY #4 KEY #1 START OFF/CANCEL 8 9 10 11 12 13 14 15 16 17 18 19 20
Display Board Display Board Connector Pinouts 9
Wiring Diagram NOTE:Schematic shows door latch switch in the COOK position with oven door open and elements off.
KITCHENAID (TULSA-BUILT) FREESTANDING MODEL KERI203P MODEL: KERI203P Keypad Layout 1 2 3 4 5 6 7 8 BROIL BAKE BREAD PROOF AUTO CONVECT CONVECT BROIL CONVECT BAKE CONVECT ROAST KEY #2 TIMER SET/START CLOCK SET/START SELF CLEAN TIMER/OFF OPTIONS KEY #9 STOP TIME COOK DURATION KEY #8 KEY #0 OVEN LIGHT KEY #6 KEY #5 KEY #3 KEY #7 KEY #4 KEY #1 START OFF/CANCEL 11 9 10 11 12 13 14 15 16 17 18 19 20
Display Board Display Board Connector Pinouts 12
Wiring Diagram L1 N NOTE: Schematic shows door latch switch in the COOK position with oven door open and elements off.
KITCHENAID (TULSA-BUILT) FREESTANDING MODEL KERA205P MODEL: KERA205P Keypad Layout KEYPAD LAYOUT Model KERA205P 14
Display Board & Connector Pinouts Low Voltage Transformer 15
Power Board 16
Wiring Diagram L1 L2 N GND BK R W W DISPLAY BOARD P2 POWER BOARD KEYPAD TRANSFORMER P1 P7-2 P5-1 T3-1 BK BK K2, BAKE RELAY T3-2 BU BK T2-1 T3-3 K3, BROIL 1 RELAY (OUTER) T2-2 P4-1 BK Y BROIL (OUTER) BU K4, BROIL 2 RELAY (INNER) T2-3 OR K7, OVEN LIGHT RELAY P4-3 R/W K9, CONVECTION FAN RELAY P4-4 OR K11, LATCH MOTOR RELAY P4-7 BR K1A, DLB 1 RELAY T1A-2 R T1A-1 R T1B-2 R T1B-1 R K1B, DLB 2 RELAY S BK BK P2 4 A LF BK S1 OR/BK OR/BK 4A OR/W OR/W S2 V 4
KITCHENAID (OXFORD-BUILT) SLIDE-IN MODEL KESI901P MODEL: KESI901P Keypad Layout MODEL KESI901P 16 15 8 7 4 3 13 COOK TIME 12 11 10 3 OPT OPEN TIMER 6 START OPEN CLOCK 9 OPEN 1 2 OVEN LIGHT OPEN 4 5 OPEN 7 8 OPEN 0 OPEN CLEAN BAKE MAXI BROIL 6 5 14 ECONO BROIL BREAD PROOF STOP TIME TIMER OFF 2 18
Display Board & Connector Pinouts Low Voltage Transformer 19
Power Board 20
Wiring Diagram N L1 W BK L2 G GND KEYPAD V V P3-2 V V P7-1 P7-2 Y GY DOOR SW P7-4 BU LATCH SW T3-2 R K3 OUTER BROIL RELAY T2-2 BU OUTER BROIL 1450 W K4 INNER BROIL RELAY T2-3 OR P2 P1 P2 K2 BAKE RELAY BK TRANSFORMER BK BK TOD 130°C (266°F) SW W THERMAL CLOSES @ 96.1°C ± 3°C W (205°F ± 5.
KITCHENAID (OXFORD-BUILT) FREESTANDING MODELS KERA807P & KERV908P, AND SLIDE-IN MODELS KESA907P & KESV808P MODELS: KERA807P, KERV908P, KESA907P, & KESV808P Keypad Layout MODELS KERA807P, KERV908P, KESA907P & KESV808P 16 8 7 15 MAXI BAKE BROIL CONVECT CONVECT BAKE BROIL 6 5 4 3 2 MEATS ECONO BROIL CONVECT ROAST BAKED GOODS WARM DRAWER BREAD PROOF FULL MEAL OTHER FOODS WARM OFF 14 13 COOK TIME 12 11 10 3 OPT OPEN TIMER 6 START OPEN CLOCK 9 OPEN 1 2 OVEN LIGHT OPEN 4 5 OPEN 7 8
Display Board & Connector Pinouts Low Voltage Transformer 23
Power Board 24
Wiring Diagram Models KESV808P & KERV908P NOTE:Schematic shows door latch switch in the COOK position with oven door open and elements off. L1 BK N G L2 W GND R W KEYPAD POWER BOARD DISPLAY BOARD V V P3-2 V V MAIN OVEN SENSOR P2 P1 P2 TRANSFORMER BK BK BK P3-1 W THERMAL SW OPENS @ 96.1 °C ± 3°C (205°F ± 5.
Wiring Diagram Models KERA807P & KESA907P NOTE: Schematic shows door latch switch in the COOK position with oven door open and elements off. L1 N G W GND BK L2 W KEYPAD R POWER BOARD DISPLAY BOARD P2 P1 P3-1 V V P3-2 V V MAIN OVEN SENSOR P3-5 OR V P3-6 OR V MEAT PROBE P3-7 GY GY P3-8 GY GY WARM DRWR SENSOR P2 P7-1 P7-2 BK TRANSFORMER BK THERMAL SW CLOSES @ 96.1°C ±3°C (205°F ±5.
KITCHENAID (OXFORD-BUILT) FREESTANDING MODEL KGRA806P & SLIDE-IN MODEL KGSA906P MODELS: KGRA806P & KGSA906P Keypad Layout MODELS KGRA806P & KGSA906P 16 8 7 4 3 14 13 12 11 10 BAKE CLEAN COOK TIME 3 OPTIONS OPEN TIMER 6 START OPEN CLOCK 9 OPEN 1 2 OVEN LIGHT OPEN 4 5 OPEN 7 8 OPEN 0 OPEN CONVECT CONVECT BAKE BROIL 6 5 15 MEATS MAXI BROIL CONVECT ROAST BAKED GOODS BREAD PROOF FULL MEAL OTHER FOODS STOP TIME TIMER OFF 2 27
Display Board & Connector Pinouts 28
Power Board 29
Wiring Diagram NOTE: Schematic shows door latch switch in the COOK position with oven door open, oven off, halo element off and light on. L1 BK W G GND W KEYPAD POWER BOARD DISPLAY BOARD P2 P1 P2 BK TRANSFORMER BK BK BK TOD 130°C (266°F) W W THERMAL SW OPENS @ 96.1°C ± 3°C (205°F ± 5.
KITCHENAID (OXFORD-BUILT) FREESTANDING MODEL KGRI801P & SLIDE-IN MODEL KGSI901P MODELS: KGRI801P & KGSI901P Keypad Layout MODELS KGRI801P & KGSI901P 16 8 15 14 13 12 11 10 BAKE CLEAN COOK TIME 3 OPT OPEN STOP TIME TIMER OFF TIMER 6 START OPEN CLOCK 9 OPEN 1 2 OVEN LIGHT OPEN 4 5 OPEN 7 8 OPEN 0 OPEN 7 6 5 4 3 MAXI BROIL BREAD PROOF 2 31
Display Board & Connector Pinouts Low Voltage Transformer 32
Power Board 33
Wiring Diagram NOTE: Schematic shows door latch switch in the COOK position with oven door open, oven off, light on and halo element off. L1 BK G GND KEYPAD POWER BOARD DISPLAY BOARD P2 P1 P3-1 V V P3-2 V V MAIN OVEN SENSOR P2 BK DOOR SW TRANSFORMER BK BK BK TOD 130°C (266°F) W W THERMAL SW OPENS @ 96.1°C ± 3°C (205°F ± 5.
WHIRLPOOL (TULSA-BUILT) FREESTANDING MODEL GR448LXP MODEL: GR448LXP Keypad Layout 1 2 3 4 5 6 7 8 9 10 11 12 13 14 BAKE BROIL CLEAN TEMP UP TEMP DOWN COOK TIME X X X X X STOP TIME TIMER SET/OFF CLOCK OVEN LIGHT HOUR UP MINUTE UP HOUR DOWN MINUTE DOWN NIGHT LIGHT WARM LOCK X X X X X X X X X X X X X X X X START OFF/CANCEL 35 X X X 15 16 17 18 19 20
Display Board & Connector Pinouts 36
Wiring Diagram NOTE: Schematic shows door latch switch in the COOK position with oven door open and elements off.
WHIRLPOOL (TULSA-BUILT) FREESTANDING MODEL GR478LXP MODEL: GR478LXP Keypad Layout MODEL GR478LXP 10 2 3 11 AUTO CLEAN DRAWER WARM 4 BROIL 5 MIN + 12 13 ADD STEP DELETE STEP WARM MIN - NIGHT LIGHT DRAWER OFF TEMP + DELAY 14 15 16 LOCK REVIEW STEP CONVECT BAKE OVEN LIGHT CHOICE BAKE TEMP - CLOCK HOUR + TIMER SET/OFF HOUR 18 - START 6 7 8 OFF CANCEL 19 38
Display Board & Connector Pinouts P1 PINOUTS P2 PINOUTS P40 -1 P1-1 P1-1 39
Power Board 40
Wiring Diagram L1 N R BK GND DISPLAY BOARD P2 P3-1 POWER BOARD KEYPAD TRANSFORMER W BK P1 P7-1 P2-1 W P5-3 R P5-1 T3-1 BK BK P3-2 P7-2 P7-4 BK T2-1 BK V T3-2 R K5, CONVECTIONRING RELAY T3-3 Y T2-2 DOOR SWITCH Y GY BU K2, BAKE RELAY K3, BROIL RELAY W MAIN OVEN SENSOR V Y DOOR LATCH SWITCH BU BAKE 2400 W CONVECTION RING BROIL BU R 1600 W THERMAL FUSE OPENS@ 184°C (363°F) BU/W 3400 W K6, WARM DRAWER RELAY P4-1 BK K8, CONSOLELIGHT RELAY BK BK P4-2 P4-3 R P4-4 OR
WHIRLPOOL (TULSA-BUILT) SLIDE-IN MODELS GS440LEM & GS445LEM MODEL: GS440LEM & GS445LEM Keypad Layout MODELS GS440LEM & GS445LEM PINS 6 5 4 3 7 CLOCK TIMER SET UNDO START TIME 8 AUTO CLEAN MINUTE UP TIMER OFF 1ST/NEXT STEP REVIEW HOUR UP STEPS HOUR CHOICE DOWN BAKE MINUTE WARMING DOWN DRAWER STOP TEMP UP TIME 9 10 START 11 12 OVEN LIGHT 2 BAKE CUSTOM BROIL WARM DRAWER OFF TEMP DOWN OFF CANCEL 13 14 42 1
Display Board & Connector Pinouts Power Board 43
Wiring Diagram N L1 BK OVEN CONTROL W P4-3 BK W P4-1 OVEN LT. GND Y P3-3 DOOR SW. P4-4 R P4-5 BR Y W W P3-4 V GY P3-1 N.O. P3-6 GY P3-2 OVEN TEMP SENSOR 1080 W @ 72°F COM V BK P3-7 DOOR LATCH SW. P2-1 P2-2 BU BU BROIL VALVE P2-4 P6 R R G P3-5 SEE NOTE 2 BK GND W SURFACE BURNER IGNITION SWITCHES BK O BAKE VALVE SPARK MODULE R J1- 10 9 7 6 4 3 2 1 TEN-PIN CONN ECTOR TOPBURNE RS GND BAKEBROIL Part No.
WHIRLPOOL (TULSA-BUILT) SLIDE-IN MODELS GS470LEM & GS475LEM MODELS: GS470LEM & GS475LEM Keypad Layout MODELS GS470LEM & GS475LEM PINS 6 5 4 3 7 CLOCK TIMER SET UNDO START TIME 8 AUTO CLEAN MINUTE UP TIMER OFF 1ST/NEXT STEP REVIEW HOUR UP STEPS HOUR CHOICE DOWN BAKE MINUTE WARMING DOWN DRAWER STOP TEMP UP TIME 9 10 START 11 12 OVEN LIGHT 2 BAKE CUSTOM BROIL WARM DRAWER OFF TEMP DOWN OFF CANCEL 13 14 45 1
Display Board & Connector Pinouts 46
Wiring Diagram NOTE: Schematic shows door latch switch in the cook position with the oven door open, oven off and light on. L1 BK BK N W P2 TAN GY BR VT OR BU Y OR WARMING SENSOR TAN W P1-1 P1-4 POWER SUPPLY BROWN WIRE CONTAINS NON-RESETABLE FUSE P7 P4-6 ON SOME MODELS BK P4-1 1 2 3 4 5 X 7 P8-1 OVEN CONTROL OVEN LIGHT LOWER OVEN TEMP SENSOR BR P4-7 P8-3 R P8-5 BR W TAN LATCH DRIVE P4-5 P4-3 UPPER OVEN TEMP SENSOR N.O. BU GY GY Y VT P4-3 P4-4 P3-2 W M COM. DOOR SW.
WHIRLPOOL (OXFORD-BUILT) SLIDE-IN MODELS GW395LEP & GY396LXP MODELS: GW395LEP & GY396LXP Keypad Layout 1 2 3 4 5 6 7 8 9 BAKE BROIL CLEAN TEMP UP TEMP DOWN COOK TIME STOP TIME TIMER SET TIMER OFF CLOCK OVEN LIGHT HOUR UP MINUTE UP HOUR DOWN MINUTE DOWN START OFF/CANCEL 48 10 11 12 13 14 15 16 17 18 19 20
Display Board & Connector Pinouts 49
Wiring Diagram Model GW395LEP L1 N NOTE: Drawing shows door is opened, unlocked, and burners off. W GND BK OVEN CONTROL P4-3 BK TRANSFORMER P4-1 W W OVEN LIGHT 1 OVEN LIGHT RELAY K-4 P4-4 DOOR SWITCH COM Y Y Y Y V V V V CONTROL TOD 96.1°±3°C (205°±6°F) W OVEN TOD 120°+10°-0°C ( 248°+18°-0°F) BK/W W P3-3 OVEN LIGHT 2 N.O.
Wiring Diagram Model GY396LXP L1 L2 N BK W GND R OVEN CONTROL BK P4-3 DOOR SWITCH COM Y Y N.O. Y Y OVEN TEMP SENSOR W OVEN LIGHT 1 CONTROL TOD 96.1°±3°C (205°±6°F) OVEN LIGHT RELAY K-4 P4-4 BK LATCH RELAY K-3 P4-5 BR COOLING FAN RELAY K-8 P4-7 GY W P3-3 P3-4 V V P3-6 V V P3-7 t° W TRANSFORMER P4-1 P3-1 P3-2 BROIL RELAY K-2 P2-2 BK P2-1 OVEN LIGHT 2 LATCH DRIVE W M COOLING FAN MOTOR BU GY N.O.
WHIRLPOOL (OXFORD-BUILT) SLIDE-IN MODEL GY398LXP MODEL: GY398LXP Keypad Layout 1 2 3 4 5 6 7 8 CONVEC BAKE BAKE BROIL CLEAN TEMP UP TEMP DOWN COOK TIME STOP TIME TIMER SET TIMER OFF CLOCK OVEN LIGHT HOUR UP MINUTE UP HOUR DOWN MINUTE DOWN START OFF/CANCEL 52 9 10 11 12 13 14 15 16 17 18 19 20
Display Board & Connector Pinouts 53
Wiring Diagram L1 L2 N BK W GND R OVEN CONTROL BK P4-3 DOOR SWITCH COM Y Y N.O. Y BK LATCH RELAY K-3 P4-5 BR P3-4 CONVECT FAN RELAY K-6 P4-6 COOLING FAN RELAY K-8 P4-7 V P3-7 V OVEN LIGHT 1 CONTROL TOD 96.1°±3°C (205°±6°F) OVEN LIGHT RELAY K-4 P4-4 V P3-6 t° W W P3-3 Y V OVEN TEMP SENSOR W TRANSFORMER P4-1 P3-1 P3-2 BROIL RELAY K-2 P2-2 BK P2-1 LATCH DRIVE OVEN LIGHT 2 W M CONVECT FAN MOTOR OR W M COOLING FAN MOTOR GY GY BU N.O.
WHIRLPOOL (TULSA-BUILT) FREESTANDING MODELS RF196LXM, RF315PXP, RF364PXP, RF365PXM, RF366LXP, RF368LXP, RF369LXP, RF378LXP, RF380LXP, SF196LEP, SF368LEP, SF369LEP, SF378LEP & SF380LEP Display And Display Board 55
Wiring Diagram Model RF315PXP N L1 L2 R BK GND PANEL LIGHT SW. W W W P6-3 P6-1 BK R W W W OVEN CONTROL OVEN LT. DOOR LIGHT SW.
Wiring Diagram Models RF196LXM & RF364PXP NOTE: Schematic shows door latch switch in the COOK position with oven door open and elements off. L1 N L2 R BK GND OVEN LT. PANEL LIGHT SW. W W W W OVEN CONTROL DOOR LATCH SW. W N/C R R W P6-3 P6-1 BK P1-2 POWER SUPPLY V P1-4 OVEN TEMP SENSOR Y DOOR LIGHT SW. P1-3 Y P1-1 BU LATCH RELAY t° Y BU N/O DOOR LATCH SW.
Wiring Diagram Models RF365PXM & RF369LXP N L1 L2 R BK GND W DOOR LATCH SW. W W W OVEN CONTROL OVEN LT. PANEL LIGHT SW. W N/C R W P6-3 P6-1 BK P1-2 Y POWER SUPPLY V P1-4 OVEN TEMP SENSOR LATCH RELAY t° DOOR LIGHT SW. P1-3 Y P1-1 BU Y BU N/O DOOR LATCH SW.
Wiring Diagram Models RF366LXP & RF368LXP NOTE: Schematic shows door latch switch in the COOK position with oven door open and elements off. L1 N L2 R BK GND PANEL LIGHT SW. W DOOR LATCH SW. W W W OVEN CONTROL OVEN LT. W N/C R R W P6-3 P6-1 BK P1-2 Y POWER SUPPLY V P1-4 OVEN TEMP SENSOR DOOR LIGHT SW. Y P1-1 BU LATCH RELAY t° N/O DOOR LATCH SW.
Wiring Diagram Models RF378LXP & RF380LXP L1 L2 N GND R BK W W OVEN LIGHT 40 W OVEN CONTROL P1-1 P1-2 R W/B U W OVEN LIGHT SWITCH DOOR SWITCH W P1-3 DOOR LIGHT SWITCH R W Y Y BU Y DOOR LATCH SWITCH Y OVEN TEMP SENSOR P1-4 P1-5 BK P6-1 BK P2-1 V V POWER SUPPLY P6-3 W K5, LATCH MOTOR RELAY P6-4 BR K4, BAKE RELAY P2-4 R K3, BROIL RELAY P2-2 BU LATCH MOTOR 4W W M BAKE 2400 W BR OIL R THERMAL FUSE OPENS @ 184°C (363°F) BU /W R 3400 W K1, DLB RELAY P2 4 A BK R R 2B
Wiring Diagram Models SF196LEP, SF368LEP, SF369LEP, SF378LEP & SF380LEP NOTE: Schematic shows door latch switch in the COOK position with oven door open, oven off and light on. L1 N W W BK TVS G W DOOR LATCH SW. (IF EQUIPPED) OVEN LT. ROCKER SW. (IF EQUIPPED) W N/C W W OVEN CONTROL BK W BK W BK P6-3 P6-1 POWER SUPPLY P1-2 Y P1-3 DOOR LIGHT SW.
WHIRLPOOL (CELAYA-BUILT) FREESTANDING MODEL SF315PEP MODEL: SF315PEP 62
Wiring Diagram OVEN LT. L1 (IF EQUIPPED) N ROCKER SW. BK BK W Y DOOR SW.
KITCHENAID GOC CLOCK MANUAL DIAGNOSTICS KITCHENAID DIAGNOSTICS DISPLAY Relay Being Engaged Latch Door F E Switch Switch Code Code Meat Probe Readout* O .
ERROR CODE Pressing the 3 key once will cycle to the next error code. An error code is displayed in the two right clock digits. 1 2 3 4 5 ERROR CODE LIST ORDER ERROR CODE #1 MOST RECENT CODE ERROR CODE #2 ERROR CODE #2 ERROR CODE #3 ERROR CODE #3 ERROR CODE #4 ERROR CODE #4 ERROR CODE #5 ERROR CODE #5 ERROR CODE DETECTION IN DIAGNOSTICS If an error code is detected in diagnostics, the code will be placed in the two right clock digits, and the system will remain in the diagnostics mode.
WHIRLPOOL GOC CLOCK MANUAL DIAGNOSTICS WHIRLPOOL DIAGNOSTICS DISPLAY Door Latch F Error E Error Switch Switch Code Code Oven Temp Sensor Readout Software Version EEPROM Warming Drawer Sensor Readout ENTERING MANUAL DIAGNOSTICS Within 120 seconds of power up, press the following keys to enable the relay capabilities listed below, and enter the manual diagnostics mode: a) Cancel key. b) Cancel key. c) Start key.
DOUBLE LINE BREAK (DLB), FANS, AND OPEN DOOR During diagnostics, all fans and elements may operate with the door open. NOTE: The latch motor will not cycle with the door open. On electric models, the double line break (DLB) will engage when entering the diagnostics mode, and will disengage when exiting the diagnostics mode. ERROR CODE Pressing the “Up” Hour key once will cycle to the next error code. An error code is displayed in the two right clock digits.
DIAGNOSTIC TEST PROCEDURES WHIRLPOOL EZ625 To enter the test: Disconnect power to the unit for at least 15 seconds, and then reconnect it. Press the following control keypads within one minute after power up: CANCEL CANCEL START The clock will run through a series of numbers. When it stops, you will be able to progress through the test process by pressing the START keypad. Test 1: Bake Relay Output The Bake relay is enabled (ignitor sparking will start in the oven—a 40 second delay after power up).
Test 2: Broil Relay Output The Broil relay is enabled (ignitor sparking will start in the oven—a 40 second delay after power up).
KITCHENAID EZ373 & 520 Test Mode: Available for the first 60 seconds after power up. Enter the Test Mode by pressing: CANCEL CANCEL START Any system or control failures will be displayed within 2 seconds. NORMAL DISPLAY ERROR DISPLAY Exit the Test Mode by pressing the OFF/CANCEL key. To recall the last error code, press the OFF/CANCEL key for 5 seconds.
WHIRLPOOL EZ354, 357, 358, & 410 Test Mode: Available for the first 60 seconds after power up. Enter the Test Mode by pressing: CANCEL CANCEL START Any system or control failures will be displayed within 2 seconds. NORMAL DISPLAY ERROR DISPLAY Exit the Test Mode by pressing the OFF/CANCEL key. To recall the last error code, press the OFF/CANCEL key for 5 seconds.
WHIRLPOOL EZ175 & 176 Self-Diagnostic Test Mode: Available for the first 60 seconds after power up. 1. Enter the Self-Diagnostic Test Mode by simultaneously pressing: BAKE and CLOCK 2. 3. The display will show “tESt”. Pressing the DOWN (t) arrow will display the following information in order shown. Pressing the UP (s) arrow will display this information in reverse order. Temperature Resistance of the Sensor (i.e. 77°) Current User Offset Value (in EPROM) (i.e.
WHIRLPOOL EZ300 Self-Diagnostic Test Mode: Available for the first 60 seconds after power up. 1. Enter the Self-Diagnostic Test Mode by sequentially pressing: TEMP DOWN TIMER OFF This test will produce a blank display, then any system or control failures will be detected within 2 seconds. 2. Pressing the CANCEL key will take the control out of the “test” mode, and into an “idle” state. NOTE: The Self-Diagnostic Mode will only allow access for 10 minutes before it times out and returns to an idle state.
— NOTES — 74
— NOTES — 75
— NOTES — 76
PRODUCT SPECIFICATIONS AND WARRANTY INFORMATION SOURCES IN THE UNITED STATES: FOR PRODUCT SPECIFICATIONS AND WARRANTY INFORMATION CALL: FOR WHIRLPOOL PRODUCTS: 1-800-253-1301 FOR KITCHENAID PRODUCTS: 1-800-422-1230 FOR ROPER PRODUCTS: 1-800-447-6737 FOR TECHNICAL ASSISTANCE WHILE AT THE CUSTOMER’S HOME CALL: THE TECHNICAL ASSISTANCE LINE: 1-800-253-2870 HAVE YOUR STORE NUMBER READY TO IDENTIFY YOU AS AN AUTHORIZED SERVICER FOR LITERATURE ORDERS: PHONE: 1-800-851-4605 FOR TECHNICAL INFORMATION AND SERVICE PO