Use & care guide

ManualsBrandsWhirlpool ManualsWashersLTE5243DT2

Table Of Contents

rWm

WashereDryer - 240 Volt

Installation Instructions

IMPORTANT:

Read and save

these instructions.

IMPORTANT:

Installer: Leave Installation Instructions

with the homeowner.

Homeowner: Keep Installation Instructions

for future reference.

Save Installation Instructions for local

electrical inspector’s use.

Part No. 3405970 Rev. B

Summary of content (9 pages)

PAGE 1
mm rWm WashereDryer - 240 Volt Installation Instructions IMPORTANT: Read and save these instructions. IMPORTANT: Installer: Leave Installation Instructions with the homeowner. Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use. Part No. 3405970 Rev.
PAGE 2
Before you start... Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to hazards that can kill 1 l 0 or hurl you and others. All safety messages will be preceded by the safety alert symbol and the word “DANGER” or “WARNING”.
PAGE 3
For use where local codes permit use of flexible power supply cord. three-wire receptacle (lo-30R) four-wire receptacle (14-30R) Figure 3 Figure 4 Fire Hazard Use a new UL approved 30 ampere power supply cord. Use a UL approved strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center terminal (silver). Ground wire (green or bare wire) must be connected to green ground connector.
PAGE 4
Exhaust requirements Where local codes permit connecting cabinet- round conductor to the neu 3ral wire of the power supply cable: Where local codes permit connecting cabinetround conductor to the neu 3ral wire: Fire Hazard Use a new UL approved 30 ampere power supply cord. Use a UL approved strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center terminal (silver).
PAGE 5
Maximum length of the exhaust system depends upon the type of vent used, number of elbows and the type of exhaust hood. The maximum length for both rigid and flexible vent is shown in the chart. Now start... with washer/dryer in laundry area. Excessive Weight Hazard Use two or more people to move and install washer/dryer. Failure to do so can result in back or other injury. Truck only from rear to prevent damage.
PAGE 6
Do Not Remove the two rear corner posts located at the back of the washer/dryer. Remove the two corner pieces attached to the lower front of the washer/dryer. Do Not remove the foam shipping pieces between the washer and dryer until the washer/dryer is in place. Numbers correspond to steps. \ rear corner posts 10 n Move foam shipping pieces outward just enough to clear the washer lid. Untape and open the washer lid. The latch under the dryer will hold lid open. 9.
PAGE 7
Move washer/dryer to its permanent location. Remove cardboard/hardboard from under washer/dryer. 23 n Carefully move the washer/dryer into final position. l Tilt the washer/dryer forward, raising back legs 1 inch off the floor so that the rear self-leveling legs will adjust. Gently lower the washer/dryer to the floor. l Check that the washer/dryer is level by placing a carpenter’s level on top of the washer, first side to side, then front to back. - If it is not level, adjust the front legs up or down.
PAGE 8
Recessed and closet installation instructions Recessed and closet hstaflat3on Pnstructjrons This washer/dryer may be installed recessed area or closet. in a The installation spacing is in inches and is minimum allowable. Additional spacing should be considered for ease of installation, servicing and compliance with local codes and ordinances. If closet door is installed, the minimum unobstructed air openings in top and bottom ore required. Louvered doors with equivalent air openings ore acceptable.
PAGE 9
If washer/dryer not operate... does Check the following to be sure that: 1. Electrical supply is connected. 2. House fuse or circuit breaker is intact and tight. 3. Washer lid or dryer door is closed. 4. Round shipping piece has been completely removed 5. Controls are set in a running or ‘ON” position. 6. Dryer start button has been firmly pushed. Part No. 3405970 Rev. B 01998 Whirlpool Corporation When moving the washerldryec.. If you need assistance...