TWOSPEED AUTOMATIC WASHERS Table of Contents ............................... 2 Appliances 3950327 www.whi rl pool.
TABLEOF CONTENTS WASHER PARTS SAFETY ............................................................ AND FEATURES USING YOUR WASHER 3 .................................................. 4 ...................................................... 5 UnderstandingWasher Cycles........................................ 5 Loading ............................................................................. 5 Normal Washer Sounds ................................................... 6 Starting Your Washer ............
WASHERSAFETY Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This symbol alerts you to hazards that can kill or hurt you and others. All willsymbol. be preceded by the safety alert symbol and the word "DANGER" or Thissafety is themessages safety alert "WARNING." These words mean: You will be killed or seriously injured if you don't follow instructions.
PARTSAND FEATURES This manual covers several different models. The washer you have purchased may have some or all of the parts and features listed below. 8 1. Control panel 7. Basket 2. Model and serial number label 8. Tub 3. Liquid fabric softener dispenser t Other features your washer 4. Agitator MAGIC CLEAN* lint filter 5. Lid XTRA ROLL ACTION PLUS* agitator 6.
USINGYOUR WASHER Loading suggestions For these suggested full-sized loads, set the LOAD SIZE selector to the highest load size setting. SUPER CAPACITY When the Cycle Control knob is set to a number and pulled out, the washer fills (to the selected load size) before agitation and timing start. The washer begins agitating immediately after filling; agitation occurs with the washer lid up or down.
Your new washer may make sounds your old one didn't. Because the sounds might be unfamiliar, you may be concerned about them. These sounds are normal. During washing When you select a small load size setting, your washer has a lower water level. This can cause a clicking sound from the upper part of the agitator. Electrical Shock Hazard During drain Plug into a grounded 3 prong outlet.
, (OPTIONAL STEP) Pour measured liquid chlorine bleach into the liquid chlorine bleach dispenser (on some models). Bleach will be diluted automatically during the wash part of the cycle. , Turn the LOAD SIZE selector to the correct setting for your wash load and the type of fabric being washed. • Choose a load size that allows the load to move freely for best fabric care. See "Loading".
11, Pull out the Cycle Control knob to start the washer. Heavy cycle This cycle features high-speed agitation followed by brief periods of low-speed agitation for cleaning sturdy fabrics and heavily soiled loads that need maximum soil removal. Select Super Wash or Regular depending on whether your load is moderately or heavily soiled. For improved cleaning, use twice the amount of detergent recommended for a wash cycle. The Heavy cycle features Extra Rinse as part of the cycle.
Whenusingextradetergentforheavilysoiledclothes,or washingspeciahcare items,youmayfindanextrarinse andspinis needed. 1. PushintheCycleControlknobandturnit clockwiseto anyofthe Rinsesettings 2, PullouttheCycleControlknob.Thewasherfillsto the selectedloadsize,agitates,drains,andspins. NOTE:An EXTRA RINSEoptionis available(onsome models).See"Startingyourwasher." CARINGFORYOUR WASHER Cleaning the exterior Use a soft, damp cloth or sponge to wipe up any spills such as detergent or bleach.
Your washer has a self-cleaning lint filter at the bottom of the basket. Wash and rinse water flow over the filter during agitation, separating the lint from the water. The lint spins out of the system during the spin part of the cycle. If your washer drains into a tub, remove any lint collected in the tub or strainer. Install and store your washer where it will not freeze. Because some water may stay in the hoses, freezing can damage your washer.
TROUBLESHOOTING First try the solutions suggested here and possibly avoid the cost of a service call... Washer won't fill, rinse or agitate Check the following: Is the power cord plugged in? Is the indicator on the Cycle Control knob properly lined up with a cycle? Turn the Cycle Control knob to the right slightly and pull to start.
Washer leaks Check the following: Are the fill hoses tight? Are the fill hose washers properly seated? Is the drain hose clamp properly installed? See the Installation Instructions. Is the sink or drain clogged? Sink and standpipe must be able to handle 17 gallons (64 L) of water per minute. Is water deflecting off the tub ring or the load? Center the tub before starting the washer. The wash load should be balanced and not overloaded. The fill or spray rinses can deflect off the load.
Load is wrinkled Did you unload the washer promptly? Unload the washer as soon as it stops. Garment damage • Did you use the right cycle for the load being washed? Use the Permanent Press cycle or another cycle with low spin speeds (if available) to reduce wrinkling. Did you overload the machine? The wash load must be balanced and not overloaded. Loads should move freely during washing.
For further assistance ASSISTANCE OR SERVICE Before calling for assistance or service, please check "Troubleshooting". It may save you the cost of a service call. If you still need help, follow the instructions below. When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request.
WHIRLPOOL* WASHERWARRANTY ONE-YEAR FULL WARRANTY For one year from the date of purchase, when this washer is operated and maintained according to instructions attached to or furnished with the product, Whirlpool will pay for replacement parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.
