MICROWAVE HOOD COMBINATION INSTALLATION INSTRUCTIONS This product is suitable for use above electric or gas cooking products up to 36" (91.4 cm) wide. These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions. Table of Contents MICROWAVE HOOD COMBINATION SAFETY .....:eceecsseseeereeners 1 INSTALLATION REQUIREMENTS Tools and Parts .......cccccccccceccceeecteeeeeeeee Location Requirements...
INSTALLATION REQUIREMENTS Tools and Parts Check the opening vo where then microwave ovenn wil The location must provide: Tools Needed Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. m= Minimum installation dimensions. See “Installation Dimensions?” illustration. mg Minimum one 2" x 4" (60.8 x 101.6 mm) wood wall stud and minimum 3/8" (9.5 mm) thickness drywall or plaster/lath within cabinet opening.
Installation Dimensions NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See “Electrical Requirements” section. A \ NN é J) B 7o S * Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. 12" (30.5 cm) min. 14" (35.6 cm) max. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Observe all governing codes and ordinances.
INSTALLATION INSTRUCTIONS remove Mounting Plate lew wie ws eyeyE Rolaie Blower Voto! NOTE: To avoid possible damage to the work surface, cover the work surface. The microwave oven is set for recirculation installation. For wall or roof venting, changes must be made to the venting system. 1. Remove any remaining contents from the microwave oven cavity. 2. Remove the mounting plate by peeling off the strips of tape that attach it to the back of the microwave oven, and set the mounting plate aside.
. Rotate blower motor end over end. gPoOnN> Roof Venting Installation Only 6. Repeat Step 1 from “Wall Venting Installation Only.” Repeat Step 2 from “Wall Venting Installation Only.” Repeat Step 3 from “Wall Venting Installation Only.” Repeat Step 4 from “Wall Venting Installation Only.” Rotate blower motor so that exhaust ports face the top of microwave oven, and flat sides of blower motor face back of microwave oven. Lower blower motor back into microwave oven.
Locale Vi Valls SrucCics) NOTE: If no wall studs exist within the cabinet opening, do not install the microwave oven. 1. Using a stud finder, locate the edges of the wall stud(s) within the opening. See illustrations in “Possible Wall Stud Configurations.” 2. Mark the center of each stud, and draw a plumb line down each stud center. See illustrations in “Possible Wall Stud Configurations.
Wall Venting Installation Only Mark Rear Wall The microwave oven must be installed on a minimum of 1 wall stud, preferably 2, using a minimum of 1 lag screw, preferably 2. 1. Centerline Upper cabinet bottom Using measuring tape, find and clearly mark the vertical centerline of the opening. t 4 ¥" (1 cm) 4" (10.2 cm) ! tt. <= A. Centerline 2.
Wall Stud at One Corner Hole (Figure 3) Atlach Mouniing Plate to Wall NOTE: Secure the mounting plate to the wall at both bottom corner holes drilled into the wall studs and/or drywall using either 1/4-20 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag With the support tabs of the mounting plate insert a 1/4-20 x 3" round-head bolt through that fits over the 3/4" (19 mm) hole drilled in “Installation for One Wall Stud at One Corner Holes in Rear Wall” section. screws.
Cut the 1%" (3.8 cm) diameter hole at the circular shaded area “G” on the template. This hole is for the power supply cord. ¥ ee install Gyine em, Pf Vi iCrowove Uven Lyn epg) NOTE: If upper cabinet is metal, the supply cord bushing needs to be installed around the supply cord hole, as shown. i 5. AWARNING B Excessive Weight Hazard Use two or more people to move and install microwave oven. Failure to do so can result in back or other injury.
NOTE: If microwave oven does not need to be adjusted, skip steps 7-9. 7. If adjustment is required, rotate microwave oven downward. Using 2 or more people, lift microwave oven off of mounting plate, and set aside on a protected surface. 8. Loosen mounting plate screws. Adjust mounting plate and retighten screws. 9. Repeat steps 3-6. 2. Connect vent to damper assembly. A B 10.
VENTING DESIGN SPECIFICATIONS This section is intended for architectural designer and builder/ contractor reference only. NOTES: mg Vent materials needed for installation are not provided with microwave hood. We do not recommend using a flexible metal vent. To avoid possible product damage, be sure to vent air outside, unless using recirculation installation. Do not vent exhaust air into concealed spaces, such as spaces within walls or ceilings, attics, crawl spaces or garages.
Recommended Vent Length A 3%" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent should be used. The total length of the vent system including straight vent, elbow(s), transitions and wall or roof caps must not exceed the equivalent of 140 ft (42.7 m) for either type of vent. See “Recommended Standard Fittings” section for equivalent lengths. For best performance, use no more than three 90° elbows.