® REFRIGERATOR USER INSTRUCTIONS THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING, please visit our website at www.whirlpool.com for additional information. If you still need assistance, call us at 1-800-253-1301. In Canada, visit our website at www.whirlpool.ca or call us at 1-800-807-6777. You will need your model and serial number located on the inside wall of the refrigerator compartment.
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions: ■ Plug into a grounded 3 prong outlet. ■ Use nonflammable cleaner. ■ Do not remove ground prong. ■ ■ Do not use an adapter. ■ Do not use an extension cord. ■ Keep flammable materials and vapors, such as gasoline, away from refrigerator. Use two or more people to move and install refrigerator. ■ Disconnect power before servicing.
Location Requirements Electrical Requirements WARNING WARNING Electrical Shock Hazard Explosion Hazard Plug into a grounded 3 prong outlet. Keep flammable materials and vapors, such as gasoline, away from refrigerator. Do not remove ground prong. Failure to do so can result in death, explosion, or fire. To ensure proper ventilation for your refrigerator, allow for a ¹⁄₂" (1.25 cm) space at the top and behind the refrigerator.
Water Pressure 5. Using a cordless drill, drill a ¹⁄₄" hole in the cold water pipe you have selected. A A cold water supply with water pressure of between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.
. Attach the copper tubing to the refrigerator with a “P” clamp. Slide the plastic waterline into the retainer. Refrigerator Doors and Drawer All graphics referenced in the following instructions are included later in this section after “Final Steps.” A B C Remove and Replace Handles To Remove Handles: 1. Grasp the lower part of the handle firmly, slide the handle up and pull the handle straight out from the door. See Plastic Handle graphics 1 and 2. To Replace Handles: 1.
Replace Doors and Hinges 1. Assemble the parts for the top hinge as shown in Top Hinge graphic. Do not tighten the screws completely. 2. Replace the parts for the bottom hinge as shown in Bottom Hinge graphic. Tighten screws. Replace the refrigerator door. NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door gasket magnets to hold the door in place while you are working. 3.
Door Removal & Replacement Top Hinges A B C 1 D A. Hinge Cover Screw B. Top Hinge Cover C. 5/16" Hex-Head Hinge Screws D. Top Hinge Bottom Hinges A B C A. Shim (on some models) B. Bottom Hinge C. Hinge Screws Connections 2 B A A. Tabs B. Wiring Plug Drawer Front Removal Drawer Front Replacement A A.
2. Raise or lower the cabinet. Style 1 - Front and rear leveling REFRIGERATOR USE Using a ³⁄₈" hex driver, turn the roller adjustment screw(s) on each side to raise or lower that side of the refrigerator. NOTE: Having someone push against the top of the refrigerator takes some weight off the adjustment screws and rollers. This makes it easier to turn the screws. It may take several turns of the roller adjustment screw to adjust the tilt of the refrigerator.
Humidity Control Cooling On/Off: ■ Cooling On/Off turns off cooling for both compartments. It does not disconnect power to the refrigerator. ■ Press and hold Cooling On/Off for 3 seconds. The LED will light up to indicate that cooling is Off. Press the button again to turn on the cooling. The LED will turn off. The humidity control feature turns on a heater to help reduce moisture on the door hinge seal. Use in humid environments or when you notice moisture on the door hinge seal.
To Access the User Preferences Menu: 1. Press and hold the Door Alarm touch pad for three seconds. The preference name will appear in the Freezer display and the preference status (F or C) or (ON or OFF) will appear in the Refrigerator display. 2. Use the Freezer (+) or (-) touch pads to scroll through the preference names. When the desired preference name is displayed, press the Refrigerator (+) or (-) touch pads to change the preference status. 3.
Replacing the Water Filter 2. Press a sturdy container against the dispenser lever. IMPORTANT: You do not need to apply a lot of pressure to the lever in order to activate the dispenser. Pressing hard will not make the water or ice dispense faster or in greater quantities. 3. Remove the container to stop dispensing. Dispenser Light NOTES: ■ The dispenser lights are LEDs which should not need to be changed. ■ When you use the dispenser, the lever will automatically turn the light on.
4. There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency. If you need to clean the condenser: ■ Remove the base grille. ■ Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area of the condenser.
The doors will not close completely ■ Door blocked open? Move food packages away from door. ■ Bin or shelf in the way? Push bin or shelf back in the correct position. Ice and Water The ice maker is not producing ice or not enough ice ■ Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open. ■ Kink in the water source line? A kink in the line can reduce water flow. Straighten the water source line.
The water and ice dispenser will not operate properly ■ Refrigerator connected to a water supply and the supply shutoff valve turned on? Connect refrigerator to water supply and turn water shutoff valve fully open. ■ Kink in the water source line? Straighten the water source line. ■ New installation? Flush and fill the water system. See “Water and Ice Dispenser.” ■ Is the water pressure at least 35 psi (241 kPa)? The water pressure to the home determines the flow from the dispenser.
PRODUCT DATA SHEETS Interior Water Filtration System Model 67003523-750 Capacity 750 Gallons (2839 Liters) System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor, Particulate Class I*; and against NSF/ANSI Standard 53 for the reduction of Lead, Mercury, Atrazine, Toxaphene, Cysts, Turbidity, Asbestos and Lindane. This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below.
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY LIMITED WARRANTY For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.
INSTRUCCIONES PARA EL USUARIO DEL REFRIGERADOR ® LE AGRADECEMOS la compra de este producto de alta calidad. Si usted experimenta un problema que no se haya cubierto en SOLUCIÓN DE PROBLEMAS, visite nuestro sitio de internet en www.whirlpool.com para obtener información adicional. Si considera que aún necesita ayuda, llámenos al 1-800-253-1301. En Canadá, visite nuestro sitio de internet en www.whirlpool.ca o llámenos al 1-800-807-6777.
Cómo deshacerse adecuadamente de su refrigerador viejo ADVERTENCIA Antes de tirar su viejo refrigerador o congelador: ■ Saque las puertas. ■ Deje los estantes en su lugar, así los niños no pueden meterse adentro con facilidad. Peligro de Asfixia Remueva las puertas de su refrigerador viejo. No seguir esta instrucción puede ocasionar la muerte o daño al cerebro. IMPORTANTE: El atrapamiento y asfixia de niños no es un problema del pasado.
NOTA: No se recomienda instalar el refrigerador cerca de un horno, radiador u otra fuente de calor. No instale el refrigerador en un lugar donde la temperatura puede ser menor de 55°F (13°C). Requisitos del suministro de agua Reúna las herramientas y piezas necesarias antes de comenzar la instalación. Lea y siga las instrucciones provistas con cualquiera de las herramientas enlistadas aquí.
Conexión del suministro de agua Lea todas las instrucciones antes de comenzar. IMPORTANTE: Si enciende el refrigerador antes de conectar la tubería de agua, ponga la fábrica de hielo en la posición de OFF (Apagado). Conexión al refrigerador Conexión a la línea de agua 1. Desenchufe el refrigerador o desconecte el suministro de energía. 2. CIERRE el suministro principal de agua. ABRA la llave de agua más cercana el tiempo suficiente para que la tubería de agua se vacíe. 3.
Complete la instalación ADVERTENCIA Cómo quitar las puertas y las bisagras IMPORTANTE: ■ Quite todos los alimentos y cualquier recipiente ajustable o de uso general de las puertas. ■ Mantenga las puertas del refrigerador cerradas hasta que esté listo para levantarlas y quitarlas de la carcasa. NOTA: Mientras quita las bisagras siempre disponga de un soporte adicional para la puerta del refrigerador.
Para volver a colocar el frente del cajón Cómo volver a poner las puertas y las bisagras en su lugar 1. Ensamble los componentes de la bisagra superior, como se muestra en la ilustración Bisagra superior. No atornille completamente los tornillos. 2. Vuelva a colocar los componentes de la bisagra inferior, como se muestra en la ilustración Bisagra inferior. Apriete los tornillos. Vuelva a poner en su lugar la puerta del refrigerador.
Cómo quitar la puerta y cambiarla Bisagras superiores A B C 1 D A. Tornillo de la cubierta de la bisagra B. Cubierta de la bisagra superior C. Tornillos de cabeza hexagonal de 5 /16" de la bisagra D. Bisagra superior Bisagras inferiores A B C A. Cuña (en algunos modelos) B. Bisagra inferior C. Tornillos de la bisagra Conexiones 2 B A A. Lengüetas B. Enchufe de cableado Cómo quitar el frente del cajón Cómo volver a colocar el frente del cajón A A.
■ Para bajar, gire el tornillo nivelador hacia la izquierda. Ajuste las puertas Según el modelo, su refrigerador puede tener cuatro rodillos regulables (Estilo 1) o un tornillo nivelador (Estilo 2) ubicado en la base del refrigerador. Si su refrigerador parece poco firme o si usted desea que la puerta se cierre con más facilidad, siga las instrucciones a continuación. 1. Quite la rejilla de la base. Tome la rejilla con firmeza y jálela hacia usted. A B A. Tornillo regulador trasero del rodillo B.
Uso de los controles El centro de control está ubicado en la parte delantera del despachador de agua y hielo. Controles de temperatura Para su conveniencia, los controles de temperatura vienen prefijados de fábrica. Cuando instale el refrigerador por primera vez, asegúrese de que los controles estén todavía fijados en los puntos fijos recomendados, como se muestra.
Door Alarm (Alarma de la puerta) La característica de Door Alarm (Alarma de la puerta) hace sonar una señal cada pocos segundos cuando la puerta del refrigerador ha quedado abierta durante 5 minutos seguidos. La señal sonará hasta que se cierre la puerta o se apague la alarma de la puerta. ■ Presione el botón táctil de Door Alarm para encender o apagar esta característica. La luz indicadora se encenderá cuando esté encendida la característica Door Alarm.
Ritmo de producción de hielo ■ Cómo despachar hielo y agua Deje transcurrir 24 horas para la producción del primer lote de hielo. Deshágase de los tres primeros lotes de hielo producidos. ■ La fábrica de hielo deberá producir aproximadamente entre 8 y 12 lotes de hielo en un período de 24 horas. ■ Para aumentar la producción de hielo, baje la temperatura del congelador y del refrigerador. Vea “Uso de los controles”. Deje pasar 24 horas entre cada ajuste.
Bloqueo del despachador El despachador puede bloquearse para facilitar la limpieza o para evitar que sea activado accidentalmente por niños pequeños o animales domésticos. NOTA: El bloqueo del despachador no interrumpe el flujo eléctrico a la unidad, a la fábrica de hielo o a la luz del despachador. Sólo desactiva todas las funciones del tablero.
4. Una limpieza rutinaria del condensador no es necesaria en ambientes normales de operación en el hogar. Si el ambiente es particularmente grasoso o polvoriento, o si hay bastante tránsito de mascotas en el hogar, el condensador deberá limpiarse cada dos o tres meses para asegurar la máxima eficacia. Si necesita limpiar el condensador: ■ Quite la rejilla de la base.
Parece que el refrigerador es ruidoso El ruido del refrigerador se ha ido reduciendo a lo largo de los años. Debido a esta reducción, es posible que escuche ruidos intermitentes en su nuevo refrigerador que no había notado en el modelo viejo. A continuación se enumeran algunos sonidos normales con explicaciones.
■ ¿Se trabó un cubo de hielo en el brazo eyector de la fábrica de hielo? Saque el hielo del brazo eyector con un utensilio de plástico. ■ ¿Tiene un filtro de agua instalado en el refrigerador? Saque el filtro y ponga a funcionar la fábrica de hielo. Si el volumen de agua aumenta, el filtro puede estar obstruido o haberse instalado incorrectamente. Reemplace el filtro o vuelva a instalarlo correctamente.
HOJA DE DATOS DEL PRODUCTO Sistema interno de filtración de agua Modelo 67003523-750 Capacidad 750 galones (2839 litros) Sistema probado y certificado por NSF International según la norma NSF/ANSI 42 para la reducción de cloro, sabor y olor, de partículas de clase I* y según la norma NSF/ANSI 53 para la reducción de plomo, mercurio, atrazina, toxafeno, quistes, turbidez, asbestos y lindano.
GARANTÍA DE LOS ELECTRODOMÉSTICOS PRINCIPALES DE WHIRLPOOL CORPORATION GARANTÍA LIMITADA Durante un año a partir de la fecha de compra, siempre y cuando se dé a este electrodoméstico principal un uso y mantenimiento de conformidad con las instrucciones adjuntas o provistas con el producto, Whirlpool Corporation o Whirlpool Canada LP (en lo sucesivo denominado “Whirlpool”) se hará cargo del costo de las piezas especificadas de fábrica y del trabajo de reparación para corregir defectos en los materiales o en
INSTRUCTIONS D'UTILISATION DU RÉFRIGÉRATEUR ® Nous vous REMERCIONS d'avoir acheté ce produit de haute qualité. Si vous rencontrez un problème non mentionné dans la section DÉPANNAGE, veuillez visiter notre site Web www.whirlpool.com pour des informations supplémentaires. Si vous avez toujours besoin d'assistance, veuillez nous téléphoner au 1-800-253-1301. Au Canada, visitez notre site Web www.whirlpool.ca ou téléphonez-nous au 1-800-807-6777.
Mise au rebut de votre vieux réfrigérateur AVERTISSEMENT Avant de jeter votre vieux réfrigérateur ou congélateur : ■ Enlever les portes. ■ Laisser les tablettes en place de sorte que les enfants ne puissent pas y pénétrer facilement. Risque de suffoquer Enlever les portes de votre vieux réfrigérateur. Le non-respect de cette instruction peut causer un décès ou des lésions cérébrales. IMPORTANT : L’emprisonnement et l’étouffement des enfants ne sont pas un problème du passé.
REMARQUE : Il est recommandé de ne pas installer le réfrigérateur près d'un four, d'un radiateur ou de toute autre source de chaleur. Ne pas installer le réfrigérateur dans un endroit où la température baissera au-dessous de 55°F (13°C). Spécifications de l’alimentation en eau Rassembler les outils et pièces nécessaires avant de commencer l'installation. Lire et suivre les instructions fournies avec les outils indiqués ici.
Raccordement de la canalisation d'eau Lire toutes les instructions avant de commencer. IMPORTANT : Si on doit utiliser le réfrigérateur avant qu’il soit raccordé à la canalisation d’eau, placer la commande de la machine à glaçons à la position OFF (arrêt). Raccordement à une canalisation d’eau Raccordement au réfrigérateur 1. Retirer le capuchon de plastique de la connexion d’alimentation en eau. Placer l’écrou en laiton et le manchon à compression sur l’extrémité du tube de cuivre. Voir l'illustration.
Achever l’installation AVERTISSEMENT Enlèvement des portes et des charnières IMPORTANT : ■ Retirer les aliments et tout balconnet ou compartiment utilitaire des portes. ■ Laisser les portes du réfrigérateur fermées jusqu’à ce vous soyez prêt à les soulever de la caisse. REMARQUE : Prévoir un support additionnel des portes pendant la réinstallation des charnières. La force d'attraction des aimants des portes ne suffit pas à les maintenir en place.
Réinstallation des portes et des charnières 1. Assembler les pièces de la charnière supérieure. Voir l'illustration de la charnière supérieure. Ne pas complètement serrer les vis. 2. Replacer les pièces de la charnière inférieure. Voir l'illustration de la charnière inférieure. Serrer les vis. Replacer la porte du réfrigérateur. REMARQUE : Prévoir un support additionnel des portes pendant la réinstallation des charnières. La force d'attraction des aimants des portes ne suffit pas à les maintenir en place.
Enlèvement et réinstallation de la porte Charnières supérieures A B C 1 D A. Vis du cache de la charnière B. Cache de la charnière supérieure C. Vis de charnière à tête hexagonale de 5/16" D. Charnière supérieure Charnières inférieures A B C A. Cale (sur certains modèles) B. Charnière inférieure C. Vis de charnière Raccordements 2 B A A. Onglets B. Fiche de branchement Dépose de la façade du tiroir A A.
■ Ajustement des portes Selon votre modèle, le réfrigérateur peut comporter quatre roulettes réglables (Style 1) ou une vis de réglage de l'aplomb (Style 2) situées à la base du réfrigérateur. Si votre réfrigérateur semble instable ou si vous désirez que les portes se ferment plus facilement, suivre les instructions ci-dessous. 1. Retirer la grille de la base. Tenir la grille fermement et tirer vers soi. Pour abaisser, tourner la vis de réglage de l'aplomb dans le sens antihoraire. A B A.
Utilisation des commandes Le centre de commande est situé dans la partie avant du distributeur d'eau et de glaçons. Commandes de température Pour votre commodité, les commandes de température sont préréglées à l’usine. Lors de l’installation initiale du réfrigérateur, s’assurer que les commandes sont encore préréglées aux points de réglage recommandés tel qu’illustré.
Door Alarm (alarme de la porte) La caractéristique Door Alarm fait retentir une sonnerie toutes les quelques secondes lorsque la porte du réfrigérateur a été laissée ouverte continuellement pendant 5 minutes. La sonnerie retentira jusqu'à ce que la porte soit fermée ou que la caractéristique Door Alarm soit désactivée. ■ Appuyer sur la touche Door Alarm pour activer ou désactiver cette caractéristique. Le témoin lumineux est allumé lorsque la caractéristique Door Alarm est activée.
Taux de production de glaçons ■ Accorder 24 heures pour produire le premier lot de glaçons. Jeter les trois premiers lots de glaçons produites. ■ La machine à glaçons devrait produire approximativement 8 à 12 lots de glaçons au cours d’une période de 24 heures. ■ Pour augmenter la production de glaçons, diminuer la température du congélateur et du réfrigérateur. Voir “Utilisation des commandes”. Attendre 24 heures entre les ajustements.
Verrouillage du distributeur Le distributeur peut être verrouillé pour un nettoyage facile ou pour éviter la distribution involontaire par de jeunes enfants ou des animaux de compagnie. REMARQUE : La fonction de verrouillage n’interrompt pas l’alimentation électrique de l’appareil, de la machine à glaçons ou de l’éclairage du distributeur. Elle désactive simplement toutes les fonctions des touches.
4. Le condenseur n'a pas besoin d'être nettoyé souvent dans des conditions de fonctionnement normales. Si l'environnement est particulièrement graisseux, poussiéreux, ou s'il y a des animaux domestiques dans la maison, le condenseur devrait être nettoyé tous les deux ou trois mois pour assurer une efficacité maximale. Si vous avez besoin de nettoyer le condenseur : ■ Retirer la grille de la base.
Le réfrigérateur semble bruyant Le bruit des réfrigérateurs a été réduit au cours des années. Du fait de cette réduction, il est possible d'entendre des bruits intermittents venant de votre nouveau réfrigérateur qui n'avaient pas été décelés avec votre ancien modèle. Voici une liste des sons normaux accompagnés d'explications.
■ La pression de l'eau est-elle inférieure à 35 lb/po² (241 kPa)? La pression de l'eau du domicile détermine l'écoulement d'eau du distributeur. Voir “Spécifications de l'alimentation en eau”. ■ Un filtre à eau est-il installé sur le réfrigérateur? Enlever le filtre et faire fonctionner le distributeur. Si l'écoulement d'eau augmente, le filtre est probablement obstrué ou mal installé. Remplacer le filtre ou le réinstaller correctement.
FEUILLES DE DONNÉES SUR LE PRODUIT Système de filtration d’eau intérieur Modèle 67003523-750 / Capacité : 750 gallons (2839 litres) Système testé et certifié par NSF International en vertu de la norme NSF/ANSI 42 (réduction du goût et de l'odeur du chlore, et particules (classe I*)); et en vertu de la norme NSF/ANSI 53 (réduction de plomb, mercure, atrazine, toxaphène, kystes, turbidité, amiante, et lindane).
GARANTIE DES GROS APPAREILS MÉNAGERS WHIRLPOOL CORPORATION GARANTIE LIMITÉE Pendant un an à compter de la date d'achat, lorsque ce gros appareil ménager est utilisé et entretenu conformément aux instructions jointes à ou fournies avec le produit, Whirlpool Corporation ou Whirlpool Canada LP (ci-après désignées “Whirlpool”) paiera pour les pièces spécifiées par l'usine et la main-d'œuvre pour corriger les vices de matériaux ou de fabrication.