RH4836 Series www.
Yoursafetyandthe safetyof othersis very important. Wehaveprovided manyimportant safetymessages inthismanual and onyourappliance. Always readand obeyatlsafetymessages. Thisisthesafetyalertsymbol. Thissymbol alertsyouto potential hazards thatcankill orhurtyouandothers. Alisafety messages wiiifoliowthesafety alert symbol andeithertheword"DANGER" or"WARNING". These wordsmean: You Ganbe killed or seri0usly injured if you don't f011owinstructions.
Wiresizesmustconformto the requirements of theNafionaU EbctdcaU CodeANSU/NFPA 70= Uatest edition_,or CSAStandards C22.1=94, Canadian EUectricaU Code Part1andC22.2No.0-M91=Uatest edition_ andaHbcaUcodesand ordinances. A U.L°or C.S.A.°listed conduit connectormustbeprovidedateach endofthepowersupplycame(at the rangehoodandatthejunction box). in U.S.only:Forpowercord connected installations, a U.L° listedrangehoodcord=connection IdtMUSTbeused.Cordkithasnot beenevaluatedfor usein Canada.
3ol/4" × 10" (8.3 × 25.4 cm) vent system 3=1/4" × 10" (8,3 x 2&4 cm) e_bow _----6 ft. { 1,8 m)----_ I wall cap I = 50 ft. Maximum length 1 - 90 ° elbow 2 ft, (0.6rn) 8 ft. (2.4 m) straight 1 = wall cap Length of 3=1/4" x 10" (8.3 x 25.4 cm) system Recommended 3=1/4" x 10" (8,3 x 25.4 crn) 90 ° eBbow = 5 ft. (1.5 m) = = = 5ft. 8ft. Oft. (15.2 m) (1.5m) (2.4m) (Om) = 13 ft. (3.9 m) standard fittings 3=1/4" x 10" (8.3 × 25.4 cm) flat eRbow = 12 ft. (3.7 m) 3=1/4" × 10" (8.3 x 25.
®Fromthe diagramsbelow, sebct the diagramfor your instalhtion. Prepare and install the hood Ventedinstallations: Cut the vent system and electrical wiring access hobs as required. Either wiring hob can be used. Non=vented installations: Cut only the one 1=1/4" (3.2 cm) dia. wiring access hob required, if wiring through the top, use Iocadon shown in VERTICAL vent systems. if wiring through the back, use location shown in HORIZONTAL vent system.
keyhole s_ot front installations, one end of the vent connector may need to be trimmed to clear the electrical strain relief. of hood ® Lift the range hood up under cabinet and determine finaU position. Mark on the underside of cabinet the Uocadon of the four keyhob mounting sbts. Set range hood aside on a protected surface. drill pilot Make electrical hobs as shown. Reinstall light lens. Depress both sides of lens, insert tabs into slots and release.
WARNING --To reducetheriskof fireor ebctrbalshock,do notuse thisfanwithanysolidostate speed controldevice, WARNING -- TO REDUCE THE RiSKOFFIRE,ELECTRIC SHOCK,ORiNJURYTO PERSONS, OBSERVE THE FOLLOWING: Usethisunitonlyin themanner intendedbythemanufacturer, if you havequestions,contactthe manufacturer.
3. Give theTeUesaUes Representative the part number needed. Care of range hood Aluminum mesh and a When it's time to reptace your aluminum filter or charcoal fiJter pads: 1. For modeU series RH4836: Order AUuminum no. 4396387. Non-vented Order RH4830 and FHter instaUUations: FHter kit no. 4396388. 2. CaUUWMrUpooU'sTeUesaUes at 1-800-442-9991. Clean he range hood with a mild detergent and soft cloth. Do not use abrasive cleansers or steel 4. The Representative wHUgive you the current price.
if you need assistance or service Call the Whirlpool Customer interaction Center toHofree at 1o800o253o1301. Our consuitants are avaHabie to assist you. When calling: PUease know the purchase date, and _ of your appUiance This information w,HU heUp us better respond to your request.
If you need assistance or service in Canada 1. if the problem is not due to one of the items listed in "Check Operation"t_. Contact the deabr from whom you purchased your appUiance, or call the IngUis Limited Consumer Assistance Centre toll-free, 8:30 a.m.- 6 p.m. (EST), at 1 800-235@665. Direct service BBmSH 2. if you need servicer... Contact your nearest UngUisLimited AppUiance Service branch or designated servicing outlet to service your appUiance. (See Uist bebw.