TKirlpool SO-INCH FREE-STANDING EYE-LEVEL ELECTRIC RANGE Models RJE-960P and RJE-963PP Control Panel Top Light Hood Knockout Upper Oven Model and Serial Number Porcelain Enamel Reflector Bowls with Chrome Trim Plate Automatic Oven Light Switch Fiberglass Heat
. Digital Clock A Minute Timer A Stop Time Knob A Start Knob .
Table of Contents ............ BEFORE USING YOUR RANGE ......... ............. USING THE SURFACE UNIT CONTROLS ................. USING THE OVEN CONTROLS l Baking. .................................... ... ... ... ................ l Broiling ., .... ............... l Variable Broil Feature .. .......... l Resetting the Oven Temperature Control Knob ...... SETTING THE CLOCK TO THE CORRECT TIME OF DAY ........... ... .... USING THE MINUTE TIMER ... USING THE AUTOMATIC MEALTIMER” CLOCK ........... .......
. Using PUSH IN and turn until the setting shows in the window. turn the Oven Knob to BAKE. unit controls The Surface Unit Control Knobs must be pushed in before turning them This helps avoid turning them on accidentally when wiping off the Control Panel. And it helps keep small children from turning them on. You must push in on them.. .then turn until the setting you want shows in the window. The four Surface Unit Controls and Signal Lights are arranged In the same order as the Surface Units.
Broiling: To broil, Selector BROIL. turn the Oven Knob to First-Follow the directions below for placlng the meat at the right distance from the Broil Element. Second-Turn the Oven Selector to “BROIL.” Third-Turn the Oven Temperature Control Knob to “BROIL” or turn it to a lower temperature (see “Variable Broil Feature.” below). Fourth-Put the broiler pan on the oven rack. Fifth-Keep the oven door open about four inches (10 cm). There is a stop in the hinges to hold it there.
< Remove the locking 1 screw; NOTICE position of notches. Resetting the Oven Temperature Control Knob: Does your new oven seem hotter or colder than your old oven? The temperatures in older ovens often shift very gradually, getting hotter or colder without the user really noticing the change. Your new oven is properly adlusted to provide accurate temperatures. but when compared to your old range, the new design may give you different baking results.
To start and stop your oven automatically: 1. Be sure the clock is set to the right time of day. (The start and stop time hands will also show the correct time.) 2. Place the food in the oven. 3. Push in and turn the Start Time Knob clockwise to the time you want the oven to start. 4. Push in and turn the Stop Time Knob clockwise to the time you want the oven to stop. 5. Turn the Oven Temperature Control Knob to the temperature you want to use to cook the food. 6. Set the Oven “TIMED.
Oven rack positions Your upper oven and lower oven each have two racks. Always put the racks where you want them to be before you turn on an oven. To remove a rack. take hold of it on the front edge and pull it out until it stops. Then lift up the front edge and pull again. It will slide past the stops. out of the glides and out of the oven. To put it back. fit the back corners into the guides at each side of the oven and slide it in.
Gasket To replace the oven light, remove glass cover and gasket. remove screws To replace top light, remove three outer screws. To replace the lower oven light bulb: The lower oven light bulb has a glass cover which is held on by a wire holder. This cover must be in place when the oven is being used. 1. Turn off the electric power at the main power supply. 2. Pull out on the wire holder and move it to one side. This will let you remove the glass cover and gasket. 3. Replace the bulb with a 40.
Your continuous Liquids spread on rough surfaces; bead up on smooth surfaces. 10 upper oven How a Continuous Cleaning Oven Works: A standard oven has walls with a smooth porcelain enamel finish. A Continuous Cleaning Oven also has a porcelain enamel finish with one important difference: instead of being smooth. like glass, the walls of a Contrnuous Cleaning Oven are a little rougher.. like the surface of a brick. A fat spatter will form a solid drop on a smooth surface.
3. Slide the foil sheet under the bake element. Make sure it is centered and long enough to start up the sides. 4. When you put the bake element back down. make sure all the feet rest solidly on the foil and that the foil is smoothed out across the bottom of the oven. If the feet on the element are not solidly on the foil. the oven may not bake properly If results aren’t what you expect: Remember. the oven keeps itself presentably clean at normal baking temperatures.
Turn on the vent hood fan or other kitchen vents durtng the cleaning cycle. This will help remove smoke, odor and heat that are normal during the cycle. l If you have a rotisserie. be sure the motor socket cover is closed. Setting the controls to the Self- Cleaning cycle: l 1. Set the Lower Oven Selector Knob to “CLEAN.” 2. Set the Lower Oven Temperature Control Knob to “CLEAN.” 3. The clock and dials for start and stop time should all have the right time of day. 4.
6. The oven will shut off when the preset stop time is reached, but the oven door will stay locked until the oven has cooled. When the Lock Light turns off, turn the Oven Selector Knob and Oven Temperature Control Knob to “OFF.” This turns off the Clean Light. Now, move the Lock Lever back to the left. Do notjorce the Lock Lever. If it doesn’t want to move easily, wait until it does. With the Lock Lever all the way to the left, the oven door can be opened. 7.
Special tips: l If the cleaning cycle doesn‘t get the oven as clean as it should be. the ttme set for cleaning was probably not long enough. Set the cleaning time longer next time. You can set it for more than 3 hours, if you want. l Plan to clean the oven before it gets too heavily soiled. Otherwise, you may notice more smoke than you would expect coming from the oven vent. And, the cleaning cycle has to be longer to clean a very soiled oven. l There WIII be normal “heat odors” during the cleaning cycle.
I ,\ Terminal Removing surface units and reflector bowls: 1 First. be sure the Surface Unit Controls are all “OFF” and that the surface units are cool. 2 See where the surface units plug into the range? Lift each surface unit about an Inch (2 5 cm) at the edge away from the plug-in (receptacle). Pull the unit strarght away from the plug-in. Do not wash surface units; they will burn themselves clean during normal use. 3 L.ift out the reflector bowls To remove surface unit, lift and pull straight out.
Prop up the top with support rod. \‘\ -:: idi Pull to stop. Lift; again. pull Cleaning under the cooktop: To clean the area under the cooktop. lift the front of the cooktop at he center. Ratse the swing-up rod to hold it. (Be sure the tip of the rod is in the notch in the cooktop ) Use warm soapy water and a sponge or cloth. Scouring powders or any other abrasive cleaner may harm porcelain enamel ftnishes and can scratch chrome.
WHAT TO USE HOW TO CLEAN Aluminum Warm, soapy water or soapy broiler pan and steel wool pads grid Control panel Oven racks l Wash with other cooking utensils l Do not place in Self-Cleanlny Oven. Warm. soapy water l Wash. rinse and dry with soft cloth Commercial glass cleaner l Follow directions Lvith cleaner. Warm. soapy water or soapy steel wool pads l Self-Cleaning Oven cycle Upper oven rack guides l Warm, soapy water or plastic scrubbing pad Self-Cleaning Oven cycle Wash.
IF YOO NEED SERVICE OR HELP, WE SUGGEST THESE THREE STEPS: YOU FOLLOW 1. Befcre you call for service : It y(~)iir rai:yG does not st’t’rll to bcl operating pr(>pe~-Iv.check the foilo~c~~~~~ tl(‘!ori’ cail~ng fc~t-SerL’Ice If nothing operates: 8 !b 117~range plugged into an operating outlet or wired into a live circuit :Litt> the i)1op~3 voltage’? (See Installation Instructions.) @ ti,l\_; ~:ou chvclt;ed the main fuse or circuit-breaker box’ If 2.
2.
FSP is a reg~sferecl trademark of Whirlpool Gxporafi~ for quality ports. Look forthis symbol of quality whenever FSP void need a replacement part for your Whlrtpool appliance. 8 FSP replacemen parts will fli right and work right, because they are made to the same exacting specifications wed to butId every new Whir!pti appliance. 0 3KirlpoolCmFoRATlON Benton Harbor, Mkhipn.
