SIDE BY SIDE REFRIGERATOR Use & Care Guide For questions about features, operation/performance, parts, accessories or service, call: 1-800-44-ROPER (1-800-447-6737). In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at... www.roperappliances.com RÉFRIGÉRATEUR CÔTE À CÔTE Guide d’utilisation et d’entretien Au Canada, pour assistance, composez le 1-800-461-5681, pour installation ou service le 1-800-807-6777 ou visitez notre site web à...
TABLE OF CONTENTS TABLE DES MATIÈRES REFRIGERATOR SAFETY .............................................................3 Proper Disposal of Your Old Refrigerator....................................3 SÉCURITÉ DU RÉFRIGÉRATEUR ..............................................25 Mise au rebut de votre vieux réfrigérateur.................................25 INSTALLATION INSTRUCTIONS ..................................................4 Unpacking .....................................................................
REFRIGERATOR SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.
INSTALLATION INSTRUCTIONS Unpacking Location Requirements WARNING WARNING Excessive Weight Hazard Use two or more people to move and install refrigerator. Failure to do so can result in back or other injury. Removing packaging materials ■ Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
Water Pressure Electrical Requirements WARNING A cold water supply with water pressure of between 30 and 120 psi (207-827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, see “Troubleshooting” or call a licensed, qualified plumber. Reverse Osmosis Water Supply Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.
Door Removal TOOLS NEEDED: ¹⁄₄ in. hex-head socket wrench, ⁵⁄₁₆ in. hex-head socket wrench and a flat-blade screwdriver. IMPORTANT: Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect power. Remove food and any adjustable door or utility bins from doors. NOTE: It may only be necessary to remove either the door handle or the doors to get your product through the doorway of your residence.
6. Disconnect wiring: Handle Removal (optional) 1. Apply firm pressure with your hand on the face of trim. Slide top trim up and bottom trim down away from handle. Lift trim pieces off shoulder screws (see Graphic 1). NOTE: Some models include accent pieces between the handle and the handle trim. If your model includes the accents, you will need to carefully remove them with a flat-blade screwdriver before removing the handle screws.
4. Align and replace the top left hinge as shown (see Graphic 4). Tighten screws. WARNING 4. Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount. 5. Replace the base grille. NOTE: Be sure to refasten the Tech Sheet behind the base grille.
Style 3 Connecting to Refrigerator Style 1 1. Unplug refrigerator or disconnect power. 2. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. 3. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent damage to the tubing when the refrigerator is pushed back against the wall. 4. Turn shutoff valve ON. 5. Check for leaks.
2. Use a sturdy container to depress the water dispenser bar until the water begins to flow. Flush the water system by dispensing and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take approximately 6 to 7 minutes and will help clear air from the line. Additional flushing may be required in some households. NOTE: As air is cleared from the system, water may spurt out of the dispenser. 3. Open the freezer door and turn on the ice maker by lowering the wire shutoff arm.
Some models dispense both cubed and crushed ice. Before dispensing ice, select which type of ice you prefer. The button controls are designed for easy use and cleaning. Adjusting Controls If you need to adjust temperatures, adjust the refrigerator temperature first. NOTE: Wait at least 24 hours between adjustments and then recheck the temperatures. Turn the control right (clockwise) to make the compartment colder. Turn the control left (counterclockwise) to make it less cold.
The Dispenser Light Water Filtration System The dispenser area has a light. It can be turned on manually by pressing the ON button (touchpad or rocker switch). On some models: Whenever you use the dispenser, the lever will automatically turn the light on. Changing the Water Filter Cartridge LIGHT OFF (on some models) NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
5. With cartridge cap in the vertical position, push the new filter cartridge into the base grille until it stops. Rotate the cartridge cap clockwise to a horizontal position. Flush the water system (see “Flushing the Water System After Replacing Filter” later in this section). To increase ice production rate: ■ Normal Ice Production: In normal ice production mode, the ice maker should produce approximately 7 to 9 batches of ice in a 24-hour period.
REFRIGERATOR FEATURES Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word “Accessory.” Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the “Accessories” section. Important information to know about glass shelves and covers: Do not clean glass shelves or covers with warm water when they are cold.
Convertible Vegetable/Meat Drawer, Crisper and Covers (on some models) Crisper and Convertible Vegetable Meat Drawers To remove and replace drawers: 1. Slide crisper or meat drawer straight out to the stop. Lift the front of drawer with one hand while supporting the bottom of drawer with other hand and slide the drawer out the rest of the way. 2. Replace the crisper or meat drawer by sliding it back in fully past the drawer stop.
FREEZER FEATURES DOOR FEATURES Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word “Accessory.” Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please call the toll-free number on the cover or in the “Accessories” section. Your model may have some or all of these features.
REFRIGERATOR CARE Cleaning Do not allow the Stainless Steel Cleaner & Polish to come into contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If accidental contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth. To order the cleaner, see the “Accessories” section. 5. There is no need for routine condenser cleaning in normal home operating environments.
Style 2 - Behind Freezer Basket Crisper Lights ■ If necessary, remove the top crisper drawer to access the crisper light shield. Remove the light shield by lifting the ends out of the brackets as shown. ■ Replace the light shield by inserting the ends into the brackets. If necessary, replace the top crisper drawer. ■ Depending on your model, remove the top freezer basket or top freezer basket shelf. Remove light shield by removing the Phillips screw on the top of the shield.
Moving When you are moving your refrigerator to a new home, follow these steps to prepare it for the move. 1. If your refrigerator has an automatic ice maker: ■ Turn off the water supply to the ice maker at least one day ahead of time. ■ Disconnect the water line from the back of the refrigerator. ■ When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting. 2.
Is an ice cube jammed in the ice maker ejector arm? For models with a standard ice storage bin, remove the ice from the ejector arm with a plastic utensil. For models with an ice storage bin on the freezer door, access the ice maker by depressing the ice sensor door on the upper left side of the freezer interior. While depressing the sensor door, lift the ice maker service door and remove the ice from the ejector with a plastic utensil. See “Ice Maker and Storage Bin.
■ Is there a water filter installed on the refrigerator? The water filtration system may have air in the lines, causing water to drip. Additional flushing may help clear air from the lines. Normal dispenser use should flush air from the lines within 24 to 72 hours. ■ Are the controls set correctly for the surrounding conditions? See “Using the Controls.” ■ Was a self-defrost cycle completed? It is normal for droplets to form after the refrigerator self-defrosts.
■ Accessory and repair parts sales. ■ Specialized customer assistance (Spanish speaking, hearing impaired, limited vision, etc.). ■ Referrals to local dealers, repair parts distributors, and service companies. Whirlpool designated service technicians are trained to fulfill the product warranty and provide afterwarranty service, anywhere in the United States. To locate the Whirlpool designated service company in your area, you can also look in your telephone directory Yellow Pages.
PRODUCT DATA SHEETS Base Grille Water Filtration System Model WF-NL300/NL300 capacity 300 Gallons (1136 Liters) Model WF-L500/L500 capacity 500 Gallons (1893 Liters) System tested and certified by NSF International against ANSI/NSF Standard 53 for the reduction of Lead; and against Standard ANSI/NSF 42 for the reduction of Taste and Odor, Chlorine Class I. This system has been tested according to ANSI/NSF 42/53 for the reduction of the substances listed below.
ROPER® REFRIGERATOR WARRANTY ONE-YEAR FULL WARRANTY ON REFRIGERATOR For one year from the date of purchase, when this refrigerator (excluding the water filter) is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor costs to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.
SÉCURITÉ DU RÉFRIGÉRATEUR Votre sécurité et celle des autres est très importante. Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer. Voici le symbole d’alerte de sécurité. Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous et à d’autres.
INSTRUCTIONS D’INSTALLATION Déballage AVERTISSEMENT Emplacement d’installation AVERTISSEMENT Risque du poids excessif Utiliser deux ou plus de personnes pour déplacer et installer le réfrigérateur. Le non-respect de cette instruction peut causer une blessure au dos ou d'autre blessure. Enlèvement des matériaux d’emballage ■ Enlever le ruban adhésif et tout résidu de colle du réfrigérateur avant de le mettre en marche.
Spécifications électriques AVERTISSEMENT REMARQUE : Votre marchand de réfrigérateurs présente une trousse disponible avec un robinet d’arrêt à étrier de ¹⁄₄ po (6,35 mm), un raccord et un tube en cuivre. Avant l’achat, s’assurer que le robinet d’arrêt à étrier est conforme à vos codes locaux de plomberie. Ne pas employer de robinet d’arrêt à étrier de ³⁄₁₆ po (4,76 mm) ou de type à percer, ce qui réduit le débit d’eau et cause une obstruction plus facilement.
Enlèvement des portes OUTILS REQUIS : Clés à douilles à tête hexagonale de ¹⁄₄ po, ⁵⁄₁₆ po, et un tournevis à lame plate. IMPORTANT : Avant de commencer, tourner la commande du réfrigérateur à OFF (arrêt), débrancher le réfrigérateur ou déconnecter la source de courant électrique. Enlever les aliments et tous les compartiments ou contenants utilitaires réglables dans les portes.
6. Déconnecter les fils : Enlèvement des poignées (facultatif) 1. Appliquer une pression forte avec votre main sur la surface de la garniture. Glisser la garniture supérieure vers le haut et la garniture inférieure vers le bas hors de la poignée. Soulever les pièces de la garniture des vis de fixation (voir dessin 1). REMARQUE : Certains modèles incluent des pièces décoratives entre la poignée et la garniture de la poignée.
4. Aligner et replacer la charnière supérieure gauche tel qu'indiqué (voir dessin 4). Serrer les vis. AVERTISSEMENT Risque de choc électrique Reconnecter les deux fils de liaison à la terre. Le non-respect de cette instruction peut causer un décès ou un choc électrique. Style 1 ■ Reconnecter les deux fils de liaison à la terre. ■ Reconnecter la fiche des fils. 3 4 1 3. Utiliser une clé à douille à tête hexagonale pour ajuster les vis de nivellement.
6. Fixer le robinet d’arrêt sur la canalisation d’eau froide avec la bride de tuyau. Vérifier que le raccord du robinet est bien engagé dans le trou de ¹⁄₄ po percé dans la canalisation et que la rondelle d’étanchéité est placée sous la bride de tuyau. Serrer l’écrou de serrage. Serrer soigneusement et uniformément les vis de la bride de tuyau afin que la rondelle forme une jonction étanche. Ne pas serrer excessivement car ceci pourrait provoquer l’écrasement du tube en cuivre. 7.
7. Brancher le réfrigérateur ou reconnecter la source de courant électrique. 8. Vider le système d’eau. Voir la section “Préparation du système d’eau”. REMARQUE : Attendre 24 heures pour produire la première quantité de glaçons. Attendre 3 jours pour que le bac à glaçons se remplisse entièrement. ■ Si votre appareil est équipé d’une machine à glaçons, vous entendrez un bruit de gargouillement lorsque la valve d’eau s’ouvre pour remplir la machine à glaçons pour chaque programme.
Ne pas obstruer l’une ou l’autre de ces ouvertures d’aération avec des aliments tels que boissons gazeuses, céréales, pain, etc. Si les ouvertures d’aération sont obstruées, le débit d’air sera bloqué et le réglage de la température ne fonctionnera pas bien. IMPORTANT : Comme l’air circule entre les deux sections, toutes les odeurs formées dans une section seront transférées à l’autre. Vous devez nettoyer à fond les deux sections pour éliminer les odeurs.
Certains modèles distribuent des glaçons en cubes et de la glace concassée. Avant la distribution de glace, choisir quelle sorte vous préférez. Les boutons de commande sont conçus pour une utilisation et un nettoyage faciles. REMARQUE : L'eau risque de ne pas avoir bon goût si le distributeur n'est pas utilisé périodiquement. Puiser une quantité suffisante d’eau chaque semaine pour maintenir un approvisionnement frais.
Après avoir changé la cartouche de filtre à eau, régler de nouveau le témoin lumineux de l’état du filtre à eau eau en appuyant sur le commutateur 5 fois en l'espace de 10 secondes. Le témoin lumineux passera du rouge au vert lorsque le système est réglé de nouveau. 2. Retirer le couvercle de la cartouche en le glissant hors du bout de la vieille cartouche. Le couvercle glissera vers la gauche ou vers la droite. NE PAS JETER LE COUVERCLE. 2 1 1. Témoin 2. Commutateur de lumière 3.
Entretien du bac d’entreposage de glaçons : Machine à glaçons et bac (sur certains modèles - Accessoire) Mise en marche/arrêt de la machine à glaçons : Le commutateur marche/arrêt pour la machine à glaçons est un bras de commande en broche situé sur le côté de la machine à glaçons. 1. Pour mettre la machine à glaçons en marche, il suffit d’abaisser le bras de commande en broche. REMARQUE : Votre machine à glaçons a un arrêt automatique.
Tablettes du réfrigérateur Votre modèle peut être doté de tablettes en verre ou de clayettes. Le remisage d’aliments semblables ensemble et le réglage des tablettes pour convenir aux différentes hauteurs réduiront le temps d’ouverture de la porte du réfrigérateur, ce qui économisera de l’énergie. Tablettes coulissantes (sur certains modèles) Pour retirer et replacer une tablette dans le cadre en métal : 1. Retirer la tablette vers l’avant jusqu’à la butée.
Les couvercles du bac à légumes ou du tiroir à légumes/viande Pour enlever et replacer les couvercles : 1. Enlever le bac à légumes et le tiroir à viande. Appuyer au centre de l’encart de verre du bac à légumes jusqu’à ce qu’il se soulève au-dessus du cadre en plastique. En tenant fermement le verre du bac à légumes, glisser soigneusement l’encart de verre vers l’avant pour l’enlever. 2. Soulever le cadre du couvercle du bac à légumes et l’enlever.
Casier à vin ou porte-cannettes/ bouteilles (sur certains modèles -Accessoire) Pour retirer et réinstaller le casier à vin (à gauche) ou le porte-cannettes/bouteilles (à droite) : 1. Retirer le casier en le tirant tout droit hors de la tablette. 2. Réinstaller le casier en le glissant entre la tablette et la paroi du réfrigérateur.
2. Réinstaller les tringles en alignant les extrémités des supports avec les attaches de chaque côté de la paroi de la porte. Enclencher fermement le support et la tringle dans les attaches au-dessus de la tablette tel qu’indiqué. ENTRETIEN DU RÉFRIGÉRATEUR Nettoyage Tringles déposées dans la porte AVERTISSEMENT Pour retirer et réinstaller les tringles : 1. Retirer les tringles en les soulevant tout droit à chaque extrémité de la tringle. 2.
Aluminium brossé : Laver avec une éponge propre ou un linge doux et un détergent doux dans de l'eau tiède. Ne pas utiliser de nettoyant fort ou abrasif, ni de nettoyant conçu pour l'acier inoxydable. Sécher à fond avec un linge doux. Fini en acier inoxydable : Laver avec une éponge propre ou un linge doux et un détergent doux dans de l'eau tiède. Ne pas utiliser de nettoyants abrasifs. Sécher à fond avec un linge doux.
Style 2 ■ Enlever le protecteur d’ampoule en saisissant les côtés et en pressant vers le centre tout en tirant le protecteur vers l’avant, tel qu'indiqué. ■ Replacer le protecteur d’ampoule en insérant les languettes dans les fentes sur la paroi interne du congélateur. Pousser le protecteur jusqu’à ce qu’il s’enclenche en position. ■ Placer 2 lb (907 g) de neige carbonique dans le congélateur pour chaque pied cube (28 L) d’espace de congélation.
2. Retirer tous les aliments du réfrigérateur et placer tous les aliments congelés dans de la neige carbonique. 3. Vider le bac à glaçons. 4. Tourner la commande du thermostat (ou la commande du réfrigérateur, selon le modèle) à OFF (arrêt). Voir “Utilisation des commandes”. 5. Débrancher le réfrigérateur. 6. Vider l’eau du plat de dégivrage. 7. Nettoyer, essuyer et sécher à fond. 8.
■ Le commutateur de la machine à glaçons est-il à la position OFF (à droite) (sur certains modèles)? Déplacer le commutateur de la machine à glaçons à la position ON (à gauche). Voir la section “Machine à glaçons et bac/seau d’entreposage”. ■ Le robinet d'arrêt de la canalisation d’eau reliée au réfrigérateur est-il ouvert? Ouvrir le robinet d’eau. Voir la section “Raccordement de la canalisation d’eau”.
Le bac à glaçons est difficile à enlever ■ Est-ce que le seau à glaçons est difficile à enlever (sur certains modèles)? Sur les modèles avec bac à glaçons dans la porte du congélateur, choisir “glaçons”. Avec un verre robuste, abaisser rapidement et dégager le bras de distribution de glace. Lorsque la porte du congélateur est ouverte, abaisser le bouton de dégagement du bac à glaçons et soulever. Voir la section “Machine à glaçons et bac”.
La pièce est-elle humide? Il est normal que l’humidité s’accumule à l’intérieur du réfrigérateur lorsque l’air de la pièce est humide. ■ ■ Les aliments sont-ils bien emballés? Vérifier que tous les aliments sont bien emballés. Essuyer les contenants humides d’aliments avant de les placer au réfrigérateur. ■ Les réglages sont-ils faits correctement pour les conditions ambiantes? Voir la section “Utilisation des commandes”.
FEUILLES DE DONNÉES SUR LE PRODUIT Système de filtration d’eau à la grille de la base Modèle WF-NL300/NL300 Capacité : 300 gallons (1 136 litres) Modèle WF-L500/L500 Capacité : 500 gallons (1 893 litres) Ce produit a été testé et certifié par NSF International en vertu de la norme 53 ANSI/NSF pour la réduction du plomb et en vertu de la norme 42 ANSI/NSF pour la réduction du goût et de l'odeur du chlore (catégorie 1).
GARANTIE DU RÉFRIGÉRATEUR ROPER® GARANTIE COMPLÈTE DE UN AN DU RÉFRIGÉRATEUR Pendant un an à compter de la date d’achat, lorsque ce réfrigérateur (à l’exclusion du filtre à eau) est utilisé et entretenu conformément aux instructions fournies avec le produit, Whirlpool Corporation paiera pour les pièces de rechange FSP® et les frais de main-d'oeuvre pour corriger les vices de matériaux ou de fabrication. Les réparations doivent être effectuées par un établissement de service désigné par Whirlpool.