OPERATION MANUAL SENSOR TUMBLE DRYER Model:SDRY60CE 90 Drying Times (mins) Start (Pause) Off Extra Dry 75 Normal Dry 60 Iron Dry 40 Extra Dry 30 Normal Dry 20 Iron Dry 10 Airing Delicate Plus Sensor Dryer Cottons Synthetics Time Remaining Delay H MIN SDRY60CE 6kg
TABLE OF CONTENTS BEFORE USING THE DRYER PLEASE READ THE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 1 INSTALLATION INSTRUCTIONS IDENTIFICATION OF PARTS INSTALLATION INSTRUCTIONS INVERTED WALL MOUNTING STACKING INSTALLATION FRONT VENTING REAR VENTING INSTALL THE FLEXIBLE HOSE 3 4 5 7 9 9 10 OPERATING INSTRUCTIONS CONTROL PANEL OPERATING INSTRUCTIONS CLEANING AND MAINTENANCE 11 11 14 TROUBLESHOOTING AND SPECIFICATIONS WIRING CIRCUIT SPECIFICATIONS TROUBLESHOOTING GUIDE 16 16 17
IMPORTANT SAFETY INSTRUCTIONS Warning - To reduce the risk of fire, electric shock, or personal injuries, the following basic precautions should be followed: 1 Read all instructions before using this dryer. 2 The interior of the dryer should be cleaned periodically by qualified service personnel. An excessive amount of lint build up in the interior of the dryer could result in inefficient drying and pose a possible fire hazard.
IMPORTANT SAFETY INSTRUCTIONS contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent - this will reduce, but not eliminate, the hazard. 15 Do not dry unwashed items in the tumble dryer. 16 Fabric softeners, or similar products, should be used as specified by the fabric softener instructions.
IDENTIFICATION OF PARTS 90 Off 75 Control panel Sensor Dryer Cottons Time Remaining Iron Dry 40 Top panel Extra Dry 30 Normal Dry 20 10 Extra Dry Normal Dry 60 Drying Times (mins) Start (Pause) Synthetics Iron Dry Airing Delicate Plus Delay H MIN SDRY60CE 6kg Program selector Service label Door switch Door airproof strip Door latch Door Exhaust grill Lint filter Model number and Serial number Power supply cord Back plate Air intake grill Outlet cover Warning Read all instructions
INSTALLATION INSTRUCTIONS Unpacking your dryer Dimensions a=830 mm b=600 mm c=560 mm Weight=30 kg Remove the transport packaging (fig.1) Remove the tape on the door (fig.2), the wall mounting kit and the inverted panel film attached to the inside of the drum (fig.3) before starting the dryer. fig.1 fig.2 fig.
INSTALLATION INSTRUCTIONS Free standing The dryer stands on the floor and can easily be moved into position. Ensure that it is placed on a level floor. Also ensure there is at least 50 mm air clearance between the back of the dryer and the wall to allow fresh air flow for efficient operation even using the front venting option.
INSTALLATION INSTRUCTIONS 2.Fix the wall hanging brackets to the wall securely (eg. into the stud). If the studs are too far apart, fit a timber slat to the studs then mount the brackets onto the slat. The distance between each is 553 mm as per diagram (Fig.1). Fig.1 553 mm Wood screw Warning: Ensure that the screw and nut of the Wall Hanging Brackets are tightened during installation, if required. Regularly check all the screws and nuts and tighten, if required. Do not overtighten. 3.
INSTALLATION INSTRUCTIONS 5.With assistance, mount dryer on wall brackets. See Fig.4. Fig.4 6. A second control panel film with inverted symbols is supplied. To fit this film, pull off the knob and then remove the old film. Peel the release paper from the back of inverted film, then place new control panel film on the surface so that the writing is the correct way around.
INSTALLATION INSTRUCTIONS 2. Install the dryer with stacking kit on the top of the front load washing machine (Fig.3). Drill two holes on both sides of washer with 2.9mm diameter drill. Detailed drill position as shown on the stacking kit. Make sure the included screws are used. Fix the stacking kit on the top cover of washing machine, as shown on Fig.4.
INSTALLATION INSTRUCTIONS Change the venting mode There are three venting options: Front venting The exhaust grill has a range of positions, which allows you to select the optimum exhaust air angle. Simply hold the grill and rotate it until you reach the desired position.
INSTALLATION INSTRUCTIONS INSTALL THE FLEXIBLE HOSE(optional Flexible hose) Connect the narrow end of the connector to the dryer duct pipe mouth at the back of the dryer. Then connect the flexible hose to the wide end of the connector. Use the clip to fasten connection point between the flexible hose and connector (fasten clip with a screwdriver). Extend the flexible hose through the duct hole, make sure the flexible hose is not twisted to allow the air to be vented outside.
CONTROL PANEL B A E 90 Drying Times (mins) Start (Pause) Off Extra Dry 75 Normal Dry 60 Iron Dry 40 Extra Dry 30 Normal Dry 20 10 Sensor Dryer Cottons Synthetics Time Remaining Delay Iron Dry Airing D C E Delicate Plus H MIN SDRY60CE 6kg A - Start/Pause button After selecting your desired drying program, press this button to start the dryer. To pause the dryer while in operation, press this button again.
OPERATING INSTRUCTIONS 3. Selecting programme Turn the program knob to set your desired drying program. a. Sensor Programs When sensor program is selected, dryness of the load will be sensed and dryer will automatically turn itself off while the clothes have dried to the dryness level selected. Programme C otton D rying level E xtra D ry* Multi-layered, thick laundry such as: terry towels, dishcloths and dry towels, bed linen, underwear, terry towelling bath robes.
OPERATING INSTRUCTIONS 6. Program completion If the display screen display “0.09”, the program comes into the cool phase. After the program is complete, the dryer will stop tumbling and the display screen will display “End”. Open the door and remove the laundry. If the laundry is not removed, the dryer will automatically commence an "anti-crease" protection cycle to keep your laundry from settling in one position and creasing. This cycle will last an hour unless the door is opened.
CLEANING AND MAINTENANCE WARNING! Unplug the power cord prior to any cleaning Cleaning the surface Wipe off any dust or dirt. Note: Do not use excessive water, a damp cloth is fine. Do not use solvent. Do not use spray cleaners when cleaning the interior. Do not use harsh or abrasive cleaners. Cleaning the filter screen To ensure good ventilation during drying, the filter screen must be cleaned before or after each use. 1. Remove the filter Gently pull out the filter screen towards yourself. 2.
CLEANING AND MAINTENANCE Cleaning the door airproof strip Remove the lint with a soft brush or a wet cloth. Be careful not to damage the airproof strip. Remove any remaining lint from the lint screen on the door at the same time. Note: The door airproof strip must be cleaned before or after each use, or the dryer may be aleak from the door in the operation. Cleaning the lint in the exhaust conduit 1. Remove the outlet cover or the exhaust grill in the trunk. 2. Take off the filter. 3.
WIRING CIRCUIT Door switch L N Sensor PCB Thermostat Capacitor M ~ Motor Heater Thermal cut-out SPECIFICATIONS ITEM TYPE SDRY60CE (220-240)V~ · 50Hz Power supply 10 Maximum operating current (A) Rated load (kg) 6 Drying program 15 2100 Maximum power (W) 830x560x600 Dimensions (HxDxW) mm Weight (kg) 30 Waterproof degree IPX4 16
TROUBLESHOOTING GUIDE If a fault occurs, before contacting Whirlpool customer service, make the following checks to try and remedy the problem: Cause Explanation / Suggestion The product may not have been plugged in, or turned on Make sure the power cord is plugged in and machine is turned on Door is not closed properly Ensure that the loading door is properly closed Programme may not have been set Check the programme has been selected Start/Pause button may not have been pressed Ensure Start/Paus
Whirlpool Customer Service Before contacting Whirlpool customer service: 1. Try to remedy the problem yourself (see “Troubleshooting Guide”). 2. Restart the programme to check whether the problem solved itself. 3. If the dryer machine continues to function incorrectly, call Whirlpool customer service. Specify: The nature of the problem. The dryer machine model. Serial number. Service Model:SDRY60CE Serial No.: The Whirlpool customer service sticker can be found inside the door. Your full address.