30" Freestanding Sealed Burner Gas Range Installation Instructions

Product Damage
The ignitor must remain in its shield when
removing bar broil burner.
Failure to do so could break ignitor.
F
n After the burners have been
converted to Natural gas usage, complete
Steps 16-17, Panel C and Step 22, Panel D.
Adjusting for proper flame
Product Damage
l Electric ignitors are used to light the oven
and broil burners. Do Not insert any
object into the openings of the shield
surrounding the ignitor coil.
l Do Not clean this area.
Failure to follow these instructions could
result in product damage.
A w Cooktop burners: Adjust the air
shutters for proper flame by sliding the air
shutter to close or open the shutter as
needed. See Panel D, Steps 19-22. Natural
gas has no yellow tip to flame.
B w Oven burner: Loosen screw and
adjust the air shutter as needed. Tighten
screw. See Panel D, Steps 23-25.
C
n Broil burner:
1, Remove the two screws fastening the front
of broil burner to oven. Pull the broil burner
forward. Loosen the lock screw on the air
shutter located at the rear of the broil
burner.
2. Adjust air shutter as needed. The flame
should be l/2” long with inner cone of bluish-
green and outer mantle of dark blue. The
flame also should be clean and soft in
character with no blowing or lifting of flame,
Tighten the lock screw. See Panel D, Steps
26-27.
Part No. 36-3 14445-02-O/4363404
0 1994 Whirlpool Corporation
D H Replace storaae drawer, oven
bottom, oven racks acd oven door. Reinstall
maintop and burner grates, burner caps and
burner bases. See Panel D, Step 22.
If range does not
operate...
l Check that the circuit breaker is not
tripped or the house fuse blown.
l Check that power supply cord is plugged
into wall receptacle.
l Check that the gas supply is turned on.
NOTE:
Refer to Use and Care Guide for operating
instructions and cleaning instructions.
Personal Injury/Product Damage Hazard
Do Not step, lean or sit on the range
drawer or door.
Failure to follow these instructions could
result in personal injury and/or product
damage.
For cleaning and
mahtenance...
If removing the range is necessary for
cleaning and maintenance, remove storage
drawer. Shut off gas supply to range.
Disconnect gas and electrical supply.
If gas or electrical supply is inaccessible, lift
range slightly at front and pull range away
from wall. Pull range out only as far as
necessary to disconnect gas and electrical
lines.
Remove range to complete cleaning or
maintenance.
Move range back into operating position.
Level range. Connect gas line to range and
check for leaks. Replace storage drawer.
w
id1 01
C3FCRWKt.
Prepared by Whirlpool Corporation, Benton Harbor, Michigan 49022
Plug power supply cord into outlet.
Make sure that rear leveling leg(s) are
engaged in anti-tip bracket(s).
If you need
assistance...
The Whirlpool Consumer Assistance Center
will answer any questions about operating or
maintaining your range not covered in the
Installation Instructions. The Whirlpool
Consumer Assistance Center is open 24 hours
a day, 7 days a week. Just dial l-(800)-253-
1301 - the call is free.
When you call, you will need the range
model number and serial number. Both
numbers can be found on the serial/rating
plate located under the maintop.
If you need
servfce...
In the event that your Whirlpool appliance
should need service, call the dealer from
whom you purchased the appliance or a
Whirlpool-authorized service company. A
Whirlpool-authorized service company is
listed in the Yellow Pages under “Appliances
- Household - Major - Service and
Repair.”
You can also obtain the service company’s
name and telephone number by dialing,
free, within the continental United States, the
Whirlpool Consumer Assistance Center
telephone number, l-(800)-253- 1301. A
special operator will tell you the name and
number of your nearest Whirlpool-authorized
service company.
Maintain the quality built into your Whirlpool
appliance - call a Whirlpool-authorized
service company.
Printed on recycled paper.
10% post consumer waste/
50% recovered materials.
Printed in U.S.A.