CALLA II SERIES WHIRLPOOL AND BATH Operating and Installation Instructions For Calla II Whirlpool and Bath INTRODUCTION Thank you for selecting our Porcher product. To ensure that your installation proceeds smoothly, read these instructions carefully before you begin. Also, review the recommended tools and materials section. Carefully unpack and examine your new plumbing fixture.
IMPORTANT SAFETY PRECAUTIONS NO UNATTENDED CHILDREN To reduce the risk of injury, do not permit children to use the bath unless they are closely supervised at all times. NO SMALL OBJECTS Keep small objects away from the whirlpool. Never drop or insert any object into any opening. Objects may be drawn into the circulation system and cause system to malfunction. Do not operate this bath without the guard over the suction fitting. Do not use attachments not recommended by the manufacturer.
HEATER OPERATING PROCEDURES The heater once installed is totally automatic. The heater will maintain the temperature of the water in the bath, or increase the temperature at about two to four degrees Fahrenheit per hour. THERMOSTAT The thermostat requires no adjustment and will automatically maintain the water temperature at 104 degrees Fahrenheit. If bath water is to warm, simply adjust by adding cold water.
DIMENSIONING DIAGRAMS Note: dimensions are nominal and may vary within the range of manufacturing tolerances. 70" [177.8] 60" [152.4] IN [CM] 39" [99.1] 9 3/4" [24.8] 34 3/4" [88.3] 26" [66.0] 18" [45.7] 35" [88.9] 4 1/4" [10.8] C/L Overflow 2" [5.1] 24 1/2" [62.2] 70" [177.8] 60" [152.4] IN [CM] 39" [99.1] 9 3/4" [24.8] 34 3/4" [88.3] 26" [66.0] 18" [45.7] 4 1/4" [10.8] C/L Overflow 35" [88.9] 2" [5.1] 24 1/2" [62.
REPLACEMENT USE When replacing an original bath, ensure to shut off the water supply and disconnect electrical power before removing. Disconnect water supply lines and drain fittings. Original supplies and fittings should be replaced on installation. INSTALLATION PROCEDURES Typical installation includes electrical power connection. Installation of house drain, floor riser, hot and cold water supply lines, shutoff vales, and fittings. Installations may require wall preparation or support framing.
Typical Pier Type Installation 22 1/2" [57.
INSTALLING BATH FOR WATERTIGHT CONNECTIONS USE TEFLON SEALANT TAPE ON PIPE THREADS STEP 1. Install 1 ½” (3.8cm) diameter house drain and ½” (1.3cm) diameter floor riser. Install hot and cold water supply lines and shutoff valves. Ensure when installing house drain that it is centered with bath drain, (when bath is placed in position), and is accessible for service through access panel. Ensure you have matched all proper dimensions. See diagram below. 8" [20.3] 1" [2.5] C/L Supply Lines 1 3/4" [4.
CAUTION: Baths are extremely heavy. For personal safety, always use extra personal for installation. STEP 2. Carefully position bath in framing, the feet should be shimmed accordingly, so that he rim of the bath contacts the leveling stringers, or pier, but supports no weight. Any finished material, such as tile or wallboard, must be self-supporting if it contacts the rim of the bath. Mount drain and overflow fittings to bath and connect assembly and house drain with tee and hand tighten EZ-nut.
STEP 4. Carefully remove construction debris from bath. Clean surfaces using soft cloth with warm water. Water-test the bath and check for leaks. INSTALLING ELECTRICAL All wiring must be performed by a licensed electrician in accordance with all local codes and the national electrical code. WARNING- When using electrical products, basic precautions should always be observed. Always disconnect the bath before servicing. Ensure installation is to permit access for service.
STEP 2. Activate whirlpool system in accordance with operating instructions for two minutes. STEP 3. Drain and refill whirlpool with cool water and circulate for additional five minutes. STEP 4. Drain whirlpool completely. FIXTURE LIMITED WARRANTY If inspection of this Porcher plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, Porcher will repair or, at its option, exchange the product for a similar model.