TQ 751 (ICE) K X/HA TQ 751 (GR) K GH/HA Français Mode d’emploi TABLE DE CUISSON Sommaire Mode d’emploi,1 Avertissements,4 Assistance,8 Description de l’appareil,10 Installation,24 Mise en marche et utilisation,28 Précautions et conseils,28 Nettoyage et entretien,29 Anomalies et remèdes,29 Italiano Español Istruzioni per l’uso PIANO Sommario Manual de instrucciones ENCIMERA Sumario Manual de instrucciones,1 Advertencias,4 Asistencia,8 Descripción del aparato,10 Instalación,30 Puesta en funcionamie
Deutsch Bedienungsanleitung KOCHMULDE Inhaltsverzeichnis Bedienungsanleitung,2 Hinweise,5 Kundendienst,9 Beschreibung Ihres Gerätes,11 Installation,42 Inbetriebsetzung und Gebrauch,46 Vorsichtsmaßregeln und Hinweise,46 Reinigung und Pflege,47 Störungen und Abhilfe,47 Nederlands Gebruiksaanwijzing KOOKPLAAT Inhoud Gebruiksaanwijzing,2 Belangrijk,6 Service,9 Beschrijving van het apparaat,11 Het installeren,49 Starten en gebruik,53 Voorzorgsmaatregelen en advies,53 Onderhoud en verzorging,54 Storingen en
Avvertenze ATTENZIONE: Questo apparecchio e le sue parti accessibili diventano molto caldi durante l’uso. Bisogna fare attenzione ed evitare di toccare gli elementi riscaldanti. Tenere lontani i bambini inferiori agli 8 anni se non continuamente sorvegliati.
CAUTION: In case of hotplate glass breakage: - shut immediately off all burners and any electrical heating element and isolate the appliance from the power supply - do not touch the appliance surface. Avertissements ATTENTION : Cet appareil ainsi que ses parties accessibles deviennent très chauds pendant leur fonctionnement. Il faut faire attention à ne pas toucher les éléments chauffants. Ne pas faire approcher les enfants de moins de 8 ans à moins qu’ils ne soient sous surveillance constante.
cuando los quemadores o la placa eléctrica todavía están calientes. Nunca utilize equipamento de limpeza a vapor ou de alta pressão para limpar o aparelho. El aparato no se debe poner en funcionamiento a través de un temporizador externo o de un sistema de mando a distancia. Elimine os líquidos presentes na tampa antes de abri-la. Não feche a tampa de vidro (se presente) se os queimadores ou a chapa eléctrica ainda estiverem quentes.
Verwenden Sie zur Reinigung des Kochfeldes keine Dampf- oder Hochdruckreinigungsgeräte. Trocknen Sie eventuell auf der Herdabdeckung befindliche Flüssigkeiten, bevor Sie sie aufklappen. Schließen Sie die Glasabdeckung (falls vorhanden) nicht, wenn die Gasbrenner oder die Elektroplatte noch heiß sind. Dieses Gerät kann nicht mit einem externen Timer oder einem getrennten Fernsteuerungssystem betrieben werden. ZUR BEACHTUNG: Die Verwendung ungeeigneter Schutzvorrichtungen kann Unfälle verursachen.
işlemleri, denetimsiz olarak çocuklar tarafından gerçekleştirilmemelidir. DİKKAT: Gres yağları ve yağlar ile korumasız küçük bir fırın bırakmak, tehlikeli olabilir ve bir yangına neden olabilir. Bir alevi/yangını su ile söndürmeye çalışmak ASLA gerekmez, ancak cihazı kapatmak ve örneğin bir kapak veya ateşe dayanıklı bir kapak ile alevin üzerini örtmek gerekir. DİKKAT: Yangın riski: pişirme yüzeyleri üzerinde nesneler bırakmayınız.
This information is found on the data plate located on the appliance and/or on the packaging. Assistenza Comunicare: • il tipo di anomalia • il modello della macchina (Mod.) • il numero di serie (S/N) Queste ultime informazioni si trovano sulla targhetta caratteristiche posta sull’apparecchio. Non ricorrete mai a tecnici non autorizzati e rifiutate sempre l’installazione di pezzi di ricambio non originali. Assistance Indiquez-lui : • le type d’anomalie • le modèle de votre appareil (Mod.
Kundendienst Geben Sie bitte Folgendes an: • die genaue Beschreibung des Fehlers • das Gerätemodell (Mod.) • die Modellnummer (S/N). Letztere Informationen finden Sie auf dem Typenschild, das sich auf dem Gerät und/oder der Verpackung befindet. Service U moet doorgeven: • het type storing • het model apparaat (Mod.) • het serienummer (S/N) Deze informatie bevindt zich op het typeplaatje links onderin het koelgedeelte. Teknik Servis şağıdaki bilgileri bildiriniz: • arıza tipi • cihazın modeli (Mod.
Descrizione dell’apparecchio Description de l’appareil Vista d’insieme Vue d’ensemble • BRUCIATORI GAS sono di diverse dimensioni e potenze. Scegliete quello più adatto al diametro del recipiente da utilizzare. • Manopole di comando dei BRUCIATORI GAS per la regolazione della fiamma. • Candela di accensione dei BRUCIATORI GAS permette l’accensione automatica del bruciatore prescelto. • DISPOSITIVO DI SICUREZZA in caso di spegnimento accidentale della fiamma, interrompe l’uscita del gas.
Descrição do aparelho Beschrijving van het apparaat Vista de conjunto Algemeen aanzicht • Os QUEIMADORES são de diferentes tamanhos e potências. Escolha o mais adequado ao diâmetro do recipiente a ser utilizado. • Selectores de comando dos QUEIMADORES A GÁS para a regulação da chama. • Vela para acender os QUEIMADORES A GÁS permite o acendimento automático do queimador escolhido. • DISPOSITIVO DE SEGURANÇA no caso em que a chama se apague acidentalmente, interrompe a saída do gás.
Posizionamento ! Gli imballaggi non sono giocattoli per bambini e vanno eliminati secondo le norme per la raccolta differenziata (vedi Precauzioni e consigli). ! L’installazione va effettuata secondo queste istruzioni e da personale professionalmente qualificato. Una errata installazione può causare danni a persone, animali o cose. ! Questo apparecchio può essere installato e funzionare solo in locali permanentemente ventilati secondo le prescrizioni delle Norme Nazionali in vigore.
• Nel caso in cui il piano non sia installato su di un forno incasso, è necessario inserire un pannello di legno come isolamento. Esso dovrà essere posizionato ad una distanza minima di 20 mm. dalla parte inferiore del piano stesso. Aerazione Per garantire una buona aerazione è necessario eliminare la parete posteriore del vano. È preferibile installare il forno in modo che appoggi su due listelli in legno oppure su un piano continuo che abbia un’apertura di almeno 45 x 560 mm (vedi figure). 560 mm .
IT • Regolazione aria primaria dei bruciatori I bruciatori non necessitano di nessuna regolazione dell’aria primaria. • Regolazione minimi 1. Portare il rubinetto sulla posizione di minimo; 2. Togliere la manopola ed agire sulla vite di regolazione posta all’interno o di fianco all’astina del rubinetto fino ad ottenere una piccola fiamma regolare. 3. Verificare che ruotando rapidamente la manopola dalla posizione di massimo a quella di minimo non si abbiano spegnimenti dei bruciatori. 4.
Tabella caratteristiche bruciatori e ugelli Tabella 1 IT Gas Liquido Bruciatore Diametro Potenza termica By-pass Ugello 1/100 1/100 (mm) kW (p.c.s.*) (mm) (mm) Nomin. Ridot. Gas Naturale Portata* g/h *** ** Ugello Portata* 1/100 l/h (mm) Rapido Ridotto (RR) 100 2.60 0.70 39 80 189 186 110(Y) 248 Semi Rapido (S) 75 1.65 0.40 28 64 120 118 96(Z) 157 Ausiliario (A) 55 1.00 0.40 28 50 73 71 79(6) 95 Mini WOK (MW) 110 3.50 1.
IT Avvio e utilizzo ! Su ciascuna manopola è indicata la posizione del bruciatore gas corrispondente. Bruciatori gas Il bruciatore prescelto può essere regolato dalla manopola corrispondente come segue: ● Spento Massimo Minimo Per accendere uno dei bruciatori, avvicinare allo stesso una fiamma o un accenditore, premere a fondo e ruotare la manopola corrispondente in senso antiorario fino alla posizione di massima potenza.
Risparmiare e rispettare l’ambiente • Cucinare gli alimenti in pentole chiuse con coperchi idonei e usare meno acqua possibile. Cucinare senza coperchio aumenterà notevolmente il consumo in termini di energia. • Usare pentole e padelle piatte. • Se si stanno cucinando alimenti con un tempo di cottura più lungo, consigliamo di usare una pentola a pressione, che è due volte più rapida e consente di salvare un terzo di energia.
! Before operating your new appliance please read this instruction booklet carefully. It contains important information for safe use, installation and care of the appliance. ! Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance. Fitting the appliance The following precautions must be taken when installing the hob: • Kitchen cabinets adjacent to the appliance and taller than the top of the hob must be at least 200 mm from the edge of the hob.
• Where the hob is not installed over a built-in oven, a wooden panel must be installed as insulation. This must be placed at a minimum distance of 20 mm from the lower part of the hob. Ventilation To ensure adequate ventilation, the back panel of the cabinet must be removed. It is advisable to install the oven so that it rests on two strips of wood, or on a completely flat surface with an opening of at least 45 x 560 mm (see diagrams). 560 mm . 45 m m.
GB • Setting the burners to minimum 1. Turn the tap to the low flame position; 2. Remove the knob and adjust the adjustment screw, which is positioned in or next to the tap pin, until the flame is small but steady. 3. Having adjusted the flame to the required low setting, while the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame does not go out. 4. Some appliances have a safety device (thermocouple) fitted.
Burner and nozzle specifications GB Table 1 Liquid Gas Burner Diameter (mm) Thermal Power kW (p.c.s.*) Nomin. Reduc. By-pass Nozzle 1/100 1/100 (mm) (mm) Natural Gas Flow* g/h *** ** Nozzle 1/100 (mm) Flow* l/h Reduced Rapid (RR) 100 2.60 0.70 39 80 189 186 110(Y) 248 Semi Rapid (S) 75 1.65 0.40 28 64 120 118 96(Z) 157 Auxiliary (A) 55 1.00 0.40 28 50 73 71 79(6) 95 Mini WOK (MW) 110 3.50 1.
GB Start-up and use ! The position of the corresponding gas burner is shown on every knob. Gas burners Each burner can be adjusted to one of the following settings using the corresponding control knob: ● Off Maximum Minimum To light one of the burners, hold a lit match or lighter near the burner and, at the same time, press down and turn the corresponding knob anti-clockwise to the maximum setting.
• If you are cooking something that takes a long time, it’s worth using a pressure cooker, which is twice as fast and saves a third of the energy. Troubleshooting Maintenance and care It may happen that the appliance does not function properly or at all. Before calling the service centre for assistance, check if anything can be done. First, check to see that there are no interruptions in the gas and electrical supplies, and, in particular, that the gas valves for the mains are open.
Conditions réglementaires d’installation (Pour la France) Le raccordement gaz devra être fait par un technicien qui assurera la bonne alimentation en gaz et le meilleur réglage de la combustion des brûleurs. Ces opérations d’installation, quoique simples, sont délicates et primordiales pour que votre table de cuisson vous rende le meilleur service. L’installation doit être effectuée conformément aux textes réglementaires et règles de l’art en vigueur et règlement sanitaire départemental.
Devant • la prise est bien compatible avec la fiche de l’appareil. Si ce n’est pas le cas, remplacez la prise ou la fiche, n’utilisez ni rallonges ni prises multiples. FR ! Après installation de l’appareil, le câble électrique et la prise de courant doivent être facilement accessibles BE ! Le câble ne doit être ni plié ni excessivement écrasé. Position du crochet pour top H=40mm ! Il doit être contrôlé périodiquement et ne peut être remplacé que par un technicien agréé (voir Assistance).
FR BE LU NL Vérification de l’étanchéité ! Une fois l’installation terminée, vérifier l’étanchéité de tous les raccords en utilisant une solution savonneuse et jamais une flamme. Adaptation aux différents types de gaz (pour la France et la Belgique) Pour adapter la table à un type de gaz autre que celui pour lequel elle a été prévue (indiqué sur l’étiquette fixée sous la table ou sur l’emballage), il faut changer les injecteurs des brûleurs en procédant comme suit : 1.
Caractéristiques des brûleurs et des injecteurs Tableau 1 (Pour la France et la Belgique) Brûleur FR Gaz Liquidés Diamètre (mm) Puissance thermique kW (p.c.s.*) Nominal Réduit By-pass Injecteur 1/100 1/100 (mm) (mm) Gaz Naturel Débit* g/h Butane Propane BE Injecteur Débit* Puissance Débit* thermique 1/100 l/h l/h kW (p.c.s.*) (mm) G20 Rapide Réduit (RR) 100 2.60 0.70 39 80 189 186 110(Y) 248 2.60 288 Semi Rapide (S) 75 1.65 0.40 28 64 120 118 96(Z) 157 1.
FR BE LU Mise en marche et utilisation ! La position du brûleur gaz correspondante est indiquée sur chaque manette. Brûleurs à gaz Chaque manette permet de régler le brûleur sélectionné comme suit : ● Eteint NL Maximum Minimum Pour allumer un brûleur, approchez une flamme ou un allume-gaz, appuyez à fond et tournez la manette correspondante dans le sens inverse des aiguilles d’une montre pour sélectionner la position de puissance maximale.
casseroles ouvertes augmente considérablement la consommation d’énergie. • Utilisez exclusivement des casseroles et poêles à fond plat. • Si vous cuisinez un aliment qui nécessite beaucoup de temps, il est préférable d’utiliser un autocuiseur qui est deux fois plus rapide et économise un tiers de l’énergie. Entretien robinets gaz Il peut arriver qu’au bout d’un certain temps, un robinet se bloque ou tourne difficilement. Il faut alors le remplacer.
Instalación ! Lea atentamente las instrucciones: contienen importante información sobre la instalación, el uso y la seguridad. Colocación ! Los embalajes no son juguetes para niños y se deben eliminar respetando las normas para la recolección de residuos (ver Precauciones y consejos). ! La instalación se debe realizar siguiendo estas instrucciones y por personal profesionalmente calificado. Una instalación incorrecta puede producir daños a personas, animales o cosas.
Adelante • la tensión de alimentación eléctrica esté comprendida dentro de los valores indicados en la placa de características; • la toma sea compatible con el enchufe del aparato. Si no es así, sustituya la toma o el enchufe; no utilice prolongaciones ni conexiones múltiples. ! Una vez instalado el aparato, el cable eléctrico y la toma de corriente deben ser fácilmente accesibles. Posición del gancho para superficies H=40mm ! El cable no debe sufrir pliegues ni compresiones.
ES En el caso del quemador Mini WOK, para aflojar la tobera utilizar una llave abierta de 7mm (veri figura). PLACA DE CARACTERÍSTICAS Conexiones eléctricas Este aparato es conforme con las siguientes Normas Comunitarias: - 2006/95/CE del 12/12/06 (Baja Tensión) y posteriores modificaciones - 2004/108/CE del 15/12/04 (Compatibilidad Electromagnética) y posteriores modificaciones - 93/68/CEE del 22/07/93 y posteriores modificaciones.
Características de los quemadores e inyectores Tabla 1 ES Gas Liquido Diametro Potencia térmica By-pass Pico 1/100 1/100 (mm) kW (p.c.s.*) (mm) (mm) Nomin. Riduc. Quemador Gas Natural Capacidad* g/h *** ** Pico Capacidad* 1/100 l/h (mm) Ràpido Reducido (RR) 100 2.60 0.70 39 80 189 186 110(Y) 248 Semi Ràpido (S) 75 1.65 0.40 28 64 120 118 96(Z) 157 Auxiliar (A) 55 1.00 0.40 28 50 73 71 79(6) 95 Mini WOK (MW) 110 3.50 1.
ES Puesta en funcionamiento y uso ! En cada mando está indicada la posición del quemador a gas correspondiente. Quemadores a gas El quemador elegido se puede regular con el mando correspondiente de la siguiente manera: ● Apagado Máximo Mínimo Para encender uno de los quemadores, acerque al mismo una llama o un encendedor, pulse a fondo y gire el mando correspondiente en sentido antihorario hasta la posición de máxima potencia.
Ahorrar y respetar el medioambiente • Cocine los alimentos en ollas o sartenes cerrados con tapas que ajusten bien y usen la menor cantidad de agua posible. Cocinar sin la tapa, aumentará enormemente el consumo de energía. • Utilice ollas y sartenes completamente planos. • Si usted está cocinando algo que toma mucho tiempo, vale la pena usar una olla a presión, que es dos veces más rápido y ahorra un tercio de la energía.
Instalação ! Leia com atenção as instruções: há informações importantes sobre a instalação, a utilização e a segurança. Posicionamento ! As embalagens não são brinquedos para as crianças e devem ser eliminadas em conformidade com as regras de colecta diferenciada (veja em Precauções e Conselhos). ! A instalação deve ser realizada segundo estas instruções e por pessoal profissional qualificado. Uma instalação errada pode causar danos a pessoas, animais ou objectos.
Frente ! Depois de ter instalado o aparelho, o acesso ao cabo eléctrico e à tomada da corrente deve ser fácil. Posição do gancho para H=40mm Atrás ! Utilize os ganchos fornecidos dentro da “embalagem dos acessórios”. • Se o plano de cozedura não for instalado sobre um forno de encaixar, é necessário inserir um painel de madeira como isolamento. O mesmo deverá ser posicionado a uma distância mínima de 20 mm da parte inferior do plano.
PT 1. Tire as grades do plano e solte os queimadores do lugar. 2. Desparafusar os bicos utilizando uma chave a tubo de 7mm, e substituílos com aqueles apropriados para o novo tipo de gás (ver tabela 1 “Características dos queimadores e dos bicos”).
Características dos queimadores e bicos Tabla 1 PT Gás Liquefeito Bruciatore Diâmetro Poténcia térmica By-pass Bico 1/100 1/100 (mm) kW (p.c.s.*) (mm) (mm) Nomin. Ridot. Gás Natural Capacidad* g/h *** ** Bico Capacidad* 1/100 l/h (mm) Ràpido Reduzido (RR) 100 2.60 0.70 39 80 189 186 110(Y) 248 Semi Rápido (S) 75 1.65 0.40 28 64 120 118 96(Z) 157 Auxiliar (A) 55 1.00 0.40 28 50 73 71 79(6) 95 Mini WOK (MW) 110 3.50 1.
PT Início e utilização ! Em cada selector está indicada a posição do queimador de gás correspondente. Queimadores a gás O queimador escolhido pode ser regulado mediante o respectivo botão da seguinte maneira : ● Apagado Máximo Mínimo Para acender o queimador aproxime do mesmo a chama de um isqueiro, fósforo ou acendedor automático, pressione e faça girar o selector escolhido no sentido anti-horário até a posição de máxima potência.
Economia e respeito do meio ambiente • Cozinhar os seus alimentos em panelas ou caçarolas fechadas com tampas bem ajustadas e usar o mínimo de água possível. Cozinhar com a tampa aberta aumentará aumentará ortemente o consumo de energia. • Usar exclusivamente panelas e caçarolas planas. • Se estiver a cozinhar algo que demora muito tempo, é melhor usar uma panela de pressão, que é dua vezes mais rápido e poupa um terço da energia.
! Die Kochmulden sind werkseitig für den Betrieb mit (siehe Typenschild und Gaseinstellungsschild des Gerätes):Erdgas Kategorie II2E+3+ eingestellt. Aufstellung ! Verpackungsmaterial ist kein Spielzeug für Kinder. Es ist entsprechend den Vorschriften zur getrennten Müllsammlung zu entsorgen (siehe Vorsichtsmaßregeln und Hinweise). ! Die Installation ist gemäß den vorliegenden Anweisungen und von Fachpersonal durchzuführen.
Haken-Befestigungsschema Position der Haken für Arbeitsplatten H=20mm Vorschriften entsprechender Schalter mit einer Mindestöffnung der Kontakte von 3 mm zwischenzuschalten. (Der Erdleiter darf vom Schalter nicht unterbrochen werden.) Das Versorgungskabel muss so verlegt werden, dass es an keiner Stelle einer Temperatur ausgesetzt wird, die 50°C über der Raumtemperatur liegt.
BE Anschluss mittels Inox-Schläuchen mit hermetischen Wänden Bei dem Anschlussstück für den Gaseingang handelt es sich um einen zylindrischen 1/2 Gas-Gewindezapfen. Der Anschluss bzw. das Verlegen dieser Schläuche muss so erfolgen, dass sie bei größter Ausdehnung eine Länge von 2000 mm nicht überschreiten. Stellen Sie nach erfolgtem Anschluss bitte sicher, dass der Inox-Schlauch nicht mit beweglichen Teilen in Berührung kommt oder an irgendeiner Stelle eingedrückt wird.
Merkmale der Brenner und Düsen BE Tabelle 1 Flüssiggas Brenner Durchmesser (mm) Wärmeleistung By-pass kW (p.c.s.*) 1/100 (mm) Nominal Reduz. 100 2.60 0.70 39 Mittelstarker Brenner (S) 75 1.65 0.40 Hilfsbrenner (A) 55 1.00 Mini Wok (MW) 110 3.50 Reduzierter Starkbrenner (RR) Menge* g/h Düse 1/100 (mm) Menge* l/h Wärme- Menge* leistung l/h kW (p.c.s.*) Butan Propan 80 189 186 110(Y) 248 2.60 288 28 64 120 118 96(Z) 157 1.65 183 0.40 28 50 73 71 79(6) 95 1.
BE Inbetriebsetzung und Gebrauch ! Auf jedem Reglerknopf ist gekennzeichnet, welcher Gasflamme er entspricht. Gasbrenner Der gewählte Brenner kann mittels des entsprechenden Reglerknopfes auf folgende Einstellungen gedreht werden: ● AUS Maximum Minimum Zum Anzünden einer Gasflamme führen Sie ein brennendes Streichholz oder einen Gasanzünder an den Brenner, drücken den entsprechenden Reglerknopf fest ein, und drehen diesen dann gegen den Uhrzeigersinn auf Höchstleistung.
Verpflichtung, dass Elektrohaushaltsgeräte gesondert entsorgt werden müssen. Endverbraucher können sich an Abfallämter der Gemeinden wenden, um mehr Informationen über die korrekte Entsorgung ihrer Elektrohaushaltsgeräte zu erhalten. Energie sparen und Umwelt schonen • Kochen Sie Ihre Nahrung in Töpfen und Pfannen mit passend geschlossenen Deckeln und verwenden Sie möglichst wenig Wasser. Ohne Deckel zu kochen führt zu einem erheblichen Energieverbrauch. • Verwenden Sie möglichst flache Töpfe und Pfannen.
ZUR BEACHTUNG BE 48
Het installeren LPG-flessen mogen dus niet worden geïnstalleerd of bewaard in vertrekken die lager liggen dan de vloer (kelders, enz.). Het is beter alleen de in gebruik zijnde fles in het vertrek te bewaren, zodanig geplaatst dat hij niet in rechtstreeks contact staat met warmtebronnen (oven, open haard, kachel, enz.) die hem tot temperaturen van meer dan 50°C zouden kunnen brengen. ! Bewaar dit boekje zorgvuldig voor eventuele verdere raadpleging.
Voor NL • de spanning zich bevindt tussen de waarden die staan aangegeven op het typeplaatje; • het stopcontact en de stekker overeenkomen. Als dat niet zo is, dient u ofwel de stekker ofwel het stopcontact te vervangen; gebruik geen verlengsnoeren of dubbelstekkers. BE ! Wanneer het apparaat geïnstalleerd is moeten het snoer en het stopcontact gemakkelijk te bereiken zijn. Stand haak voor keukenblad H=40mm Achter ! De kabel mag niet worden gebogen of samengedrukt.
Controleren gasdichtheid ! Nadat het installeren heeft plaats gevonden moet de perfecte gasdichtheid van alle verbindingsstukken worden gecontroleerd met een zeepoplossing en nooit met een vlam. Aanpassen aan de verschillende soorten gas (voor België) Voor het aanpassen van de kookplaat aan een ander soort gas dan waarvoor hij is bestemd (aangegeven op het typeplaatje aan de onderkant van de kookplaat of op de verpakking), moeten de straalpijpjes van de branders op de volgende wijze worden vervangen: 1.
NL Kenmerken van de branders en de straalpijpjes Table 1 (Voor Belgie) BE Gaspit Vloeibaar gas Doorsnee (mm) Thermisch vermogen kW (p.c.s.*) Nominaal Gereduc. By-pass Straal. 1/100 1/100 (mm) (mm) Natuurlijk gas Bereik* g/h Butane Propanea Straal. 1/100 (mm) Bereik* Thermisch Bereik* vermogen l/h l/h kW (p.c.s.*) G20 G25 Gereduceerd snel (RR) 100 2.60 0.70 39 80 189 186 110(Y) 248 2.60 288 Half-snel (S) 75 1.65 0.40 28 64 120 118 96(Z) 157 1.
Starten en gebruik ! Op iedere knop staat aangegeven waar de gasbrander zich precies bevindt. Gasbranders De gekozen brander kan met de betreffende knop als volgt worden geregeld: ● Uit Maximum Minimum Om een van de branders aan te steken dient u er een vlam of aansteker bij te houden, de knop stevig in te drukken en tegen de klok in te draaien tot u het maximum vermogen heeft bereikt.
NL BE Onderhoud en verzorging Storingen en oplossingen De elektrische stroom afsluiten Het kan gebeuren dat het kookvlak niet (afdoende) functioneert. Voordat u de servicedienst belt dient u te controleren of u het euvel zelf kunt oplossen. Verifieer om te beginnen of er een correcte stroom- en gastoevoer is, en in het bijzonder of de hoofdgasleiding open staat. Sluit altijd eerst de stroom af voordat u tot enige handeling overgaat.
! Her gerektiğinde başvurulabilmesi için bu el kitapçığının muhafaza edilmesi önemlidir. Cihazın satılması, başkasına verilmesi ya da taşınması durumunda yeni kullanıcının işleyiş ve ilişkin uyarılar hakkında bilgi edinmesi için el kitapçığının cihazla birlikte verildiğinden emin olunuz. ! Talimatları dikkatli bir şekilde okuyunuz: kurulum, kullanım ve emniyet hakkında önemli bilgiler içermektedir.
TR Gaz bağlantısı ! “Aksesuar paketi” nde bulunan kancaları kullanınız. • Set üstü ocağın ankastre fırın üzerine monte edilmemesi durumunda, izolasyon amacıyla bir ahşap levhanın takılması gerekmektedir. Bu levha tezgahın alt kısmından en az 20 mm. mesafeye yerleştirilmelidir. Havalandırma İyi bir havalandırma sağlanması için yuvanın arka duvarının çıkarılması gerekir.
• Minimum ayarlaması 1. Gaz vanasını minimum konumuna getiriniz; 2. Düğmeyi söküp vana milinin iç tarafında ya da yanında bulunan ayar vidasına küçük ve düzenli bir alev elde edene kadar müdahale ediniz. TR 3. Düğmeyi maksimum pozisyondan minimum pozisyona döndürünce brülörlerin sönmediğinden emin olunuz. 4. Emniyet aygıtı olan cihazlarda (ısı pili), brülörler minimum konumdayken bu aygıtın çalışmaması durumunda, ayar vidasına müdahale ederek minimumları yükseltiniz. 5.
TR Brülör ve memelerin özellikleri Çizelge 1 Sıvı gaz Ocak Çap (mm) Doğal gaz Termik güç By-pass Meme Tasima gücü* Meme Tasima 1/100 1/100 1/100 gücü* g/saat (mm) (mm) (mm) l/saat Nomin. Reduc. *** ** kW (p.c.s.*) Azaltılmış hızlı (RR) 100 2.60 0.70 39 80 189 186 110(Y) 248 Yarı hızlı (S) 75 1.65 0.40 28 64 120 118 96(Z) 157 Yardımcı (A) 55 1.00 0.40 28 50 73 71 79(6) 95 Mini WOK (MW) 110 3.50 1.
Başlatma ve kullanım ! Her bir düğme üzerinde kumanda ettiği gaz brülörünün konumu belirtilmiştir. Gaz brülörleri Seçilmiş olan brülör, ilgili düğme vasıtasıyla aşağıdaki konumlara ayarlanabilir: ● Kapalı Maksimum Minimum Ocakların birini yakmak için bir çakmak ya da yakıcı yaklastırınız, basılı tutarak ilgili dügmeyi maksimum pozisyonuna getirene kadar saatin ters yönünde döndürünüz.
195129200.00 12/2014 - XEROX FABRIANO TR Servis ve bakım Gaz vanalarının bakımı Zamanla bir vananın kilitlenmesi yada zor döndürülmesi durumu ortaya çıkabilir; böyle bir durumda değiştirilmesi gerekecektir. Elektrik akımının devre dışı bırakılması Herhangi bir işlem yapmadan önce cihazın elektrik şebekesine bağlantısını kesiniz. ! Bu işlem üretici firma tarafından yetkilendirilmiş bir teknisyen tarafından yapılmalıdır.