30" (76.2 CM) RANGE HOOD For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301 or visit our website at www.whirlpool.com in Canada, call 1-800-807-8777 or visit our website at www.whirlpool.ca HOTTIE D’ASPIRATION DE 30" (76,2 CM) Au Canada. pour assistance, installation ou service. composer le 1-800-807-6777 ou visitor note site Web & www.whirlpool.
TABLE OF CONTENTS RANGE HOOD SAFETY .. INSTALLATION REQUIREMENTS. Tools and Parts. Location Requirements Venting System . Electrical Requirements INSTALLATION INSTRUCTIONS. RANGE HOOD USE. Range Hood Controls RANGE HOOD CAR Cleaning WIRING DIAGRAM ASSISTANCE OR SERVICE. in the U.S.A. TABLE DES MATTRESSES SECURITY DE LA HOTTIE DE SINECURE EXIGENCES L¥INSTALLATION Cu tillage ef Exigences d’emplacement.
State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer, WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm IMPORTANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Use this unit only in the manner intended by the manufacturer, i you have questions, contact the man
INSTALLATION REQUIREMENTS Gather the required tools and parts before starting installation. Read and follow the instructions provided Wotan soups with any tools listed here, Wire Grips £2 Philips screwdriver, Tools needed 20 Gallbladder. <7 screwdriver Drill with: 14”. 13 mime, 24 Pencil (3 om} bits SH 3 (131mm) Fs ang TH #7 Caulking gun and weatherproof coking compound 5 Jigsaw or keyhole saw Parts supplied Flyleaves parts from package. Check that all parts are included. #818 x 5% J {4.
Installation Clearances minimum distance from electric cooking surface 24° (61 nm) minion distance from gas cooking surface 50" 76.2 om) suggested maximum above the cooking surface 18° (45.7 omy minimum clearance upper cabinet 1o counter top L 40" (76.2 om) minimum cabinet opening width L 12° (30.8 omy cabinet depth S46 (97.4 om) base cabinet height moon Venting Methods NOTES: ® Flexible vent is not recommended. Flexible vent crates both back pressure and air turbulence that greatly reduce performance.
Calculating Vent System Length To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system Vent System Vent Piece 457 elbow 2.5108 m) gi 80° elbow Sfti1s5m 7° (17.8 cry wall cap aft {0m} P Example vent system 90° stow Wall cap {1.8m} zis elbow =5# (1.5m) 1 wall cap = 0H {0m} 8 ft 12.4 m) straight Stern length = 13H pom) Maximum Recommended Length 7° {17.8 om) Round Vent = 80 Hf {15.2 m) ~ Observe all governing codes and ordinances.
INSTALLATION INSTRUCTIONS 3. Install Brackets NOTES: @ Depending on your model, determine which venting method to use: roof or wall, ® [tis recommended that the vent system be installed before the range hood is Installed. Go to “Venting System” in the “Installation Requirements” section if you need assistance. ® Before making cutouts, make sure there is proper clearance within the ceiling or wall for the vent system. 1. Disconnect Power EE TUTTI 2 Electrical Shock Hazard Disconnect power before servicing.
5. Mark Hole Locations 6. Mark and Cut Vent Opening Lift the range hood into place and insert the mounting bracket tabs through the slots in the back of the range hood. Hold the range hood firmly in place with one hand and bend each mounting tab (A) upward approximately 90° Mark the hole af the power supply knockout (8). Mark the 4 vent hole locations {C} on the top of the range hood, OPTIONAL: Mark the hole in each mounting tab. Remove the range hood and set if aside, 7% {17.
8. Prepare Range Hood Vents and Mounting Tabs install Strain Relief Install a UL Listed Approved (18 mm) strain relief (A). Mounting Tabs Start a #8-18 x 54" (4.2 x 16 mm) truss-head screw into the mounting fab (0) on each side of tha range hood as shown in the inset. Insert the screws approximately 2 turns into the mounting tab holes. 7" (17.8 cm} Round Vent Installations Remove both top knockouts (8 and CG). 8. Attach Vent Damper or Transition 7" {17.
12. Make Electrical Connection Option 1 Direct Wire installations a Uses UL Listed Approved wire connector and connect the 3 white wires (A) together. ® Use a UL Listed Approved wire connector and connect the 2 black wires (B) together. aL Fire Hazard Electrically ground the blower. Use copper wire. Connect ground wire to green ground screw in terminal box. Failure to do so can result in death, fire, or electrical shock.
RANGE HOOD CARE IMPORTANT: Clean the hood and grease filters frequently according to the following instructions. Replace the grease filter before operating hood, Exterior Surfaces IMPORTANT: Do not use soap-filled scouring pads, abrasive clues 5, cookie polishing creme, cites! wool gritty washcloths, ar paper towels. To avoid carnage to the stainless steel, do not use cleaners that contain chlorine.
ASSISTANCE OR SERVICE If you need service Please refer to the warranty page in this manual. If you need replacement parts If you need to order replacement parts, we recommend that you use ably factory specified parts. Factory specified parts will fit right and work right because they are made with the same precision Used to build every new appliance. To locate factory specified replacement parts in your area, call the following customer assistance telephone number or your nearest designated service center.
ATTACH YOUR RECEIPT HERE, PROOF OF PURCHASE roman eon tat fe at when you call the MAJOR APPLIANCE Him ae nd phone mes LIMITED WARRANTY | 200 ied baritone no pompom = Proof of purchase including dealer or retailer name and address IF YOU NEED SERVICE: [a] Lae 1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be addressed without service.