30" (76.2 CM) AND 36" (91.4 CMR RANGE HOOD Hons crt Use ficus nisei For questions about features, operation/performance, parts, accessories of service, call or visit our website at www.whilpool.com In Canada, call 1-800-807-8777 or visit our website at www, whirlpool HOTTIE D’ASPIRATION DE 30" (76,2 CM) ET 36" (91,4 co instructions ofinstoliofion of Guides of Au Canada, pour assistance, Installation ou service, composer le 1-800-807-6777 ou visitor note site Web & www.
TABLE OF CONTENTS RANGE HOOD SAFETY .. INSTALLATION REQUIREMENTS. Tools and Parts... Location Requirements Venting Requirement: Electrical Requirements INSTALLATION INSTRUCTIONS. Prepare Location... Install Range Hood... Make Electrical Connection . Complete Installation RANGE HOOD USE. Range Hood Controls RANGE HOOD CAR Cleaning. WIRING DIAGRAM ASSISTANCE OR SERVICE. In the U.S.
IMPORTANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OH INJURY TO PERSONS, OBSERVE THE FOLLOWING: # Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. # Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
INSTALLATION REQUIREMENTS cols caned Pres Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed Drill 14" (3.0 om) drill bit Ya" {3.0 mm drill bit for pilot holes Pencil Wire stripper or utility knife Tape measure of ruler Caulking gun and weatherproof caulking compound Flat-blade screwdriver Phillips screwdriver Barber or keyhole saw Metal snips Compass of 8° {20.
Installation Clearances A, 18" (45.7 cm) min. clearance upper cabinet to counter top BL 18" (45.7 om} to 24" (67.0 cm) suggested man. bottom of range hood to cooking surface ©.30° (76.2 cin) min. cabinet opening width for 30° (76.2 cn) models and 36" (91.4 em) min. cabinet with for 36” 91.4 m) models. D. 13° (33.0 cm) cabinet depth E. 35" (91.4 cm) base cabinet height w Do not germinate the vent system in an attic or other enclosed area Do not use a 4" {10.2 om) laundry-type wall cap, Use a 7° {17.
Calculating Vent System Length To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system. 7" {17.8 cm) Round Vent System Vent Piece Round 45° elbow 251 08m S0° elbow 5.01 [7° (17.8 cry wall cap 001 JA" x10" B3emx2540mp 45H to 7" (17.8 cm} (1.4m) 3a" x 107188 cmx 25.4 cm) B.01ft to 77 (17.8 cm) 80° elbow [Example vent system 74 (17.8 om) bound 20° elbow Wall cap | J et(tEm 06m) Maximum Recommended Length = 50 ft (15.2 m) 1-90° elbow =5.0ft (1.
INSTALLATION INSTRUCTIONS NOTE: It is recommended that the vent system be installed before hood is installed. Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent. 1. Disconnect power. 2. Depending on your model. determine which venting method to use: roof or wall. 3. Select a flat surface for assembling the range hood. Place covering over that surface. 4. Lit the range hood and set it upside down onto covered surface 5.
4. Use saber or keyhole saw to cut the circular vent opening. Th, 7 7 {18.4 orm} diam. machine! drools “From wall, not cabinet frame Install Vent System 1. Install vent through the vent opening in upper cabinet or wall, Complete venting system according to the selected venting method. See “Venting Requirements” section. 2. Use caulking to seal exterior wall or roof opening around the cap. 1.
2. Remove the screw from the terminal box cover. Remove terminal box cover and set aside. Boe nasal Terminal box cover B. Screw 3. Remove the power supply knockout from the top or rear of the vent hood {depending on the incoming location of your home power supply cable) and install a UL listed or CSA approved 4" strain relief. A Power supply knockout 4. Using 2 or more people, lift the hood into final position.
FF noggin Eom Bon Gs sib ong! ARCH RES TER 1. Install the 75W {max.} Incandescent light bulb. See 3. Check the operation of the range hood fan and light. See “Replacing the Incandescent Light Bulb” section. “Range Hood Use” section. 2. Replace grease filter if removed. See the “Range Hood Care” if range hood does not operate, check to see whether a section. circuit breaker has tripped or a household fuse has blown. Disconnect power and check wiring connections.
RANGE HOOD CARE So IMPORTANT: Clean the hood and grease filters frequently according to the following instructions. Replace grease filter before operating hood. Exterior Surfaces: IMPORTANT: Do not use soap-filled scouring pads, abrasive cleaners, Cookie Polishing Crane, steel wool, gritty washcloths or paper towels. To avoid damage to the stainless steel, do not use cleaners that contain chlorine. Cleaning Method: m Rub in direction of grain to avoid scratching or damaging the surface.
ASSISTANCE OR SERVICE When calling for assistance or device, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond ta your request. If you need replacement parts If you need to order replacement parts, we recommend that you use only factory specified parts. Factory specified parts will fit right and work right because they are made with the same precision used to build every new appliance.
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY LIMITED WARRANTY For one year from the date of purchase. when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship, Service must be provided by a Whirlpool designated service company.
SÉCURITÉ DE LA HOTTE DE CUISINIÈRE Votre sécurité et celle des autres est trais importante. Nous donnas de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer.
AVERTISSEMENT : POUR RÉDUIRE LE RISQUE D’INCENDIE, HOC électrique OU DOMMAGES CORPORELS, RESPECTER LES INSTRUCTIONS SUIVANTES ® Utiliser cot appareil uniquement dans les applications envisagées par le fabricant. Pour toute question, contacter le fabricant, # Avant entreprendre un travail d’entretien ou de nettoyage, Interrompre Alimentation de la hotte au niveau du tableau de disjoncteurs, of verrouiller le tableau de disjoncteurs pour empêcher tout rétablissement accidentel de Alimentation du circuit.
EXIGENCES D'INSTALLATION Chis ef pid Rassembler les outils et pièces nécessaires avant d'entreprendre Installation. Lire et observer les instructions fournies avec chacun des outils de la liste ci-dessous.
Distances de dégagement a respecter A, Dégagement min. de 18" (45,7 cm) entre fe placard supérieur et Ie plan de travail 8.18" (45,7 em) 4 24° (61,0 om) distance maximale suggérée du bus de fa yole & fa surface te cuisson C.30° (78,2 am) de large tir de cabinet min. pot les modes de 30" (76.2 cim) et 36" (91,4 om) de largeur lits. de placard pour Jes matie les de 36” (81,4 cm). D.
Calcul de fa longueur du circuit d'évacuation Pour calculer la longueur effective du circuit o évacuation nécessaire, additionner les longueurs équivalents {en pieds ou métrés) de tous les composants utilisés dans le système, Système d'évacuation avec conduits ronds de 7" (17,8 cm} Composant Rond Coude 0,8m) LJ [ Coude Bouche de décharge murale Opt de 7" {17.8 (83cm x 254 (17.8 om) {1.4 Raccord coud & 90° de 314” x 10" (8,3 om x 25.
INSTRUCTIONS ID’INSTALLATION scarifier REMARQUE : Il est recommandé d'installer le système évacuation avant de procéder a installation de la hotte. Avant d'exécuter les découpages, vérifier la disponibilité d'un dégagement suffisant dans le plafond ou le mur pour le conduit d'évacuation 1. Déconnecter la source de courant électricienne. 2. Selon le modelé, déterminer la méthane d'évacuation & utiliser : décharge a travers Je mur ou le toit. 3. Sélectionner une surface plane pour l'assemblage de la hotte.
Découpage d’ouvertures pour un conduit d’évacuation rond de 7° (17,8 cm} Pour le découpage d'ouvertures pour conduit rend sur la face inférieur du fond ou du sommet du placard © 1. Tracer un axe central sur la face inférieurs du sommet du placard. 2. Tracer une ligne de 5" (12.7 cm) en partant du mur arriéra sur 1a face inférieure du sommet ou du fond du placard. 3. Utiliser un compas ou un gabarit circulaire pour tracer un cercle avec un diamètre de 14" (0,64 om) supérieur 4 celui du conduit d'évacuation.
8. 22 Retirer la plagie de montage du conduit rond de 7" (17,8 crm) fixé avec des vis & l’intérieur de la hotte, A. Prague de montage de conduit rond de 7" (17,8 cm) B Vis installer une plaque de partage de clapet anti-reflux rond de 77 {17,8 cm). La fixer a la hotte 4 l'aide des vis fournies. REMARQUE : Un clapet anti reflux rond est disponible comme accessoire. Pour commander des pièces, voir la section “Accessoires”. A Clapet anti-roulis rand de 7 (17.8 om) fuir la section “Accessoires”) B.
Hissage de chou électrique Déconnecter la source de courant électrique avant Entretien. Replacer pinces et panneaux avant de faire la remise en marche. Le non-respect de ces instructions peut causer un décès ou un chie diélectrique. 1. Reconnecter la source de courant électrique. Go A. Conducteurs blancs E. Ensemble d’accessoires B. Conducteurs noirs câble d’alimentation du oo domicile ou cordon ©, Connecteur de tifs a tis amalgamation UL) E Serre-câble homologué UL D.
UTILISATION DE LA HOTTE La hotte de cuisinière est congrue pour extraire fumée, vapeurs de cuisson et odeurs de la zone de la table de cuisson. Pour obtenir les meilleurs résultats, mettre le ventilateur de la hotte en marche avant d’entreprendre une cuisson, et laisser le ventilateur fonctionner pendant plusieurs minutes après 'achèvement d'une cuisson pour pouvoir évacuer de la cuisine toute trace d’odeur de cuisson, vapeur ou fumés, Les commandes de Ia hotte sont situées sur le sommet de la note, B a A.
Remplacement de 'ampoule a incandescence Éteindre la hotte et laisser 'ampoule refroidir. 1. Déconnecter la source de courant électrique. 2. Exercer une pression sur le cabochon en plastique de protection pour pouvoir le retirer de la hotte, A Dolly de lampourde B. Cabochon 4 5.
ASSISTANCE OU SERVICE Lors d'un appel pour assistance ou service, veuillez connaître la date d’archal, le numéro de modelé ef le numéro de série complets de Appareil. Ces renseignements nous aideront & mie répondre a votre demande. Si vous avez besoin de pièces de rechange Bi vous avez besoin de commander des pièces de rechange, nous vous recommandons d’ employer uniquement les piges spécificatrices par Fusion.
GARANTIE DES GROS APPAREILS MÉNAGERS WHIRLPOOL CORPORATION GARANTIE LIMITÉE Pendant un an a compter de la date d'achat, lorsque ce gros appareil] ménager est utilisé et entretenu conformément aux instructions Jointes a ou fournies avec le produit, Whirlpool Corporation ou Whirlpool Canada LP {ci-après désignées "Whirlpool”} paiera pour les pièces spécifies par Usine et la pour corriger les vices de matériaux ou de fabrication. Le service doit être fourni par une compagnie de service désignée par Whirlpool.